Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 9 of 9
Hello guys,
I am using a Prusa I3 Single Nozzle Printer with an Ramps 1.4 (Prusa MK 2S clone).
The firmware I am using is the Prusa I3 Mk 2S Ver 3.1.0 optimized from Slippyr4:
Slippyr4 Github
I added a thermistor on my board on Pin 15 -> Temp_1_PIN.
The thermistor is connected to the internals of my power supply. I want to read the power supply temperature, if the temp is higher than a tre
by
Foxen
-
Firmware - mainstream and related support
Hello,
I am using a Prusa I3 and I am using Kisslicer and Slic3r for my prints.
I am printing PLA 1,75 mm with a jhead nozzle.
I try to print large prints, for example the blossoming lamp from thingiverse.
The lamp took about 9 hours ... or so ... some users reported they have print that in 4 and a half hour.
Is it somehow possible to get my prints even faster ?? I have set my perimeter to 80
by
Foxen
-
General
Hello Guys, I try to print a Mario figure with support but unfortunately ... it will make the support everywhere,
is it somehow possible to force the support only under the arms ??? not @ the center like in the picture ?
I am using Slic3r.
Picture is attached
This is the Mario, I try to print from Thingiverse: Mario
by
Foxen
-
General
Hello, I have built up an Prusa I3 with nearly perfect X and Y Axis,
They are all well calibrated.
I tried now Kisslicer, Slic3r and Cura. and printed a Test plug, with every Slicer.
In every of these 3 Slicer the hole is 0,5 mm too small, outside Dimensions are great.
I know it is due too Arc Compensation.
But why does someone have good holes and bad holes ... Is it also related to the Noz
by
Foxen
-
General Mendel Topics
so if this is the formula I have 200*16/0,8 = 4000
I am using M5 rod for z axis but 4000 is too fast for marlin :/
what should i do ?
by
Foxen
-
Repetier
Hi same Problem here with calibration but it worked with that!
Calibration Guide NICE!
by
Foxen
-
General Mendel Topics
Good evening,
I managed to get my printer run today calibrated everything and I am quite happy now.
I am running Ramps 1.4 and the Sprinter Firmware.
I also bought an LCD Display from ReprapDiscount
Now I want to get it running.
But on the Official site, they get them running on the Marlin firmware.
So now my question:
Can I use the same code that is provided on the website for the Marlin F
by
Foxen
-
General Mendel Topics
Good evening I bought the Ramps Ultimate package from reprapdiscount.
now I want to wire my stepper motor to the Ramps board.
I followed the guide here: Guide
My connectors should look like this
but unfortunately my connectors looks like this:
So Blue and Red are interchanged, does it make any differents ?
Or should i wire it like on the first picture ?
(The wires were preasembled in
by
Foxen
-
General Mendel Topics
Good evening guys,
I want to built an Prusa i3 Printer equiped with a prusa Nozzle,
I want to use this Extruder :
Gregs Wade Extruder
Now there are 3 Stl versions of it:
The:
* groovemount
* jhead mount
* reprap-fab.org
Which one will fit ? for the Prusa Nozzle ?
Cause on the official site there is the following statement:
Developer Batch #0 units are shipped with Wade extruder comp
by
Foxen
-
General Mendel Topics