Show all posts by user
Page 1 of 2
Pages: 12
Results 1 — 30 of 34
This is the Repetier log as I am starting to try and run something to see what happens
7:58:20 PM: Unknown option bed_shape
7:58:20 PM: Unknown option dont_support_bridges
7:58:20 PM: Unknown option wipe
7:58:20 PM: Unknown option xy_size_compensation
7:58:20 PM: Unknown option support_material_contact_distance
7:58:20 PM: Unknown option external_fill_pattern
7:58:20 PM: Arg
by
DMPurdy
-
Reprappers
I did follow the guide, nothing is happening other than it connects to the printer via communication now. It still does not heat extruder or bed. Do I now need to load something else to activate that?
by
DMPurdy
-
Reprappers
It says done uploading after I closed it and saved and then reopened Arduino
by
DMPurdy
-
Reprappers
Okay I found the port now, I also had a bunch of sketches saved so I took the first one and renamed it INO
by
DMPurdy
-
Reprappers
Okay, I see what you are saying but I don't have anything that says ino other than blink.ino I also do not know what port to choose as I only have these bluetooth and iMac ones? I think there was a 1421 before but I have no idea wtf happened to that one.
by
DMPurdy
-
Reprappers
Here is what is happening. Now it didn't error out but said timeout avrdude...
by
DMPurdy
-
Reprappers
So I redownloaded the Marlin and Arduino and am at the point to hit the upload and when I do it just says "error compiling" on the Marlin Ramps Epcos i38-2
by
DMPurdy
-
Reprappers
I have the Marlin downloaded but not sure if it is synced with IDE? what is the IDE exactly? Sorry I am very new to this... If someone can just guide me into the the first few steps of loading software and setting up board I would be very grateful.
by
DMPurdy
-
Reprappers
Hello Hello anyone out there
by
DMPurdy
-
Reprappers
t just says connecting or if I hit send it says printer not online
by
DMPurdy
-
Reprappers
I also checked the D2 auxillary as you asked and it is in fact getting 12 volts..
by
DMPurdy
-
Reprappers
It just says connecting or if I hit send it says printer not online
by
DMPurdy
-
Reprappers
Ill check the 12v but how do you send m119 on pronterface exactly?
by
DMPurdy
-
Reprappers
Well the unit powers on but does not heat the bed or extruder. I have checked my wiring over and over and was sent a new ramp board with no success. I looked everything over with baud rate and so forth but am I missing a step in entering a startup code? I am not sure about the " " or how exactly changes are to be made or entered. The temperature control is non responsive and I have gotten nothing
by
DMPurdy
-
Reprappers
I have Prusa I3 Folger Tech aluminum model and I have tried to figure out wtf I am doing wrong and just cannot. If someone could PM me who is knowledgable on the Arduino and Marlin software or Printrun and help me with a few questions on logging commands to begin with I would greatly appreciate it.
by
DMPurdy
-
Reprappers
what videos? I still cannot get my printer to work or the heat bed or thermistor to get hot or do anything
by
DMPurdy
-
Prusa i3 and variants
Any ideas? It only shows progress to about 9/10 of the bar and does nothing else....grrrr had this for a month and still cannot get the damn thing to work or load
by
DMPurdy
-
Reprappers
I get an unknown firmware waiting for printer error at the very bottom of Repetier host mac screen.
I will try and go over it here and explain all the errors/ inactivity better. I apologize for being too vague.
by
DMPurdy
-
Firmware - mainstream and related support
I don't have the lcd control panel. I had the arduino box come up but it seems like whatever I enter in it says an error at the bottom. I ran the Marlin software but wasn't sure if I needed to configure the ramps or how to access that. On the main printer interface it shows it is connected to the printer via usb and I am able to input the codes but nothing happens when it says it is printing or t
by
DMPurdy
-
Firmware - mainstream and related support
Okay I have downloaded the software for my Prusa I3 kit on mac but have no clue how to even start it up? I know that the printer powers on and I attempted to print but the heat bed does not warm up nor the extruder. I am thinking I missed some step somewhere setting up software? Any help or suggestions would be greatly appreciated.
by
DMPurdy
-
Firmware - mainstream and related support
It is a digital meter, there is an ohm reading and also the audible signal path, which I also checked and it did produce sound as an open circuit. I have rechecked the wiring multiple times now and it is correct. The heat bed is not working.
by
DMPurdy
-
Prusa i3 and variants
I think I have a bad heat bed or board, I have double and triple checked my wiring and still not heating at all....
by
DMPurdy
-
Prusa i3 and variants
Are the LEDs supposed to be flashing on the electronic boards? My red and green are constantly flashing.
by
DMPurdy
-
Reprappers
Are the LEDs supposed to be flashing on the electronic boards? My red and green are constantly flashing on the Folger Tech I3 Prusa?
by
DMPurdy
-
Reprappers
Thanks I will give it a try...Also, is the the glass piece supposed to be secured down to the heat bed or just loose? It seems like it may slide around.
by
DMPurdy
-
Prusa i3 and variants
How did you put the tensioner on? I didn't see anything on how to do that in the instructions.I am having trouble with my bed not heating. It is the first time I have started it and tried anything so not sure what I am missing.
by
DMPurdy
-
Prusa i3 and variants
Can I ask you about how you built the first part? I have the aluminum 2020 i3 and thought i was missing the halves that cover the two bearings but support told me they do not use them on the newer model. So wtf I can't find a clear diagram or pdf that shows the 2020 aluminum build? In step 3 it shows using the bearing covers. Sorry for imposing on your post but hoping I can get started on this.
by
DMPurdy
-
Prusa i3 and variants
Page 1 of 2
Pages: 12