Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 29 of 29
Hi Dust,
5d means 5 dimensional where revolving and rotational axis will be there. And I want to add to marlin firmware with respect to arduino and ramps.
by
swaroop
-
General
Hi to all
I want to make 5d printing with marlin firmware and ramps 1.4 board. can anyone help with this
Thanks advance
by
swaroop
-
General
Hi dc42,
Thanks dc42.
by
swaroop
-
Duet
We are building a printer to print inside a cup(petri dish)... so the change in extruder can lead to the nozzle hitting the brim of the cup
by
swaroop
-
General
i am trying to make it in the firmware so that its easier for operation... along with the tool change command if we could incorporate this, it would be really helpful for further tweeks
by
swaroop
-
General
I built a Prusa with a dual extruder where tool change happens with the help of servo.
the sequence of tool change that is currently happening;
...Z lift by 10mm ...servo changes tool ...X axis and Z axis(10mm) moves offset simultaneously
this is the normal operation
The sequence of movement that I require is;
...Z lift by 10mm ...servo changes tool ...X axis should move and then ...Zaxis sh
by
swaroop
-
General
Hi dc42,
I am new to duet board. and i want to know where is the Pins_Duet.h is located and also what changes i have to make in sys folder? please help me in detailed?
by
swaroop
-
Duet
Hi to all,
I have Duet board 0.6 and I want to add fan controlled. I can use expansion header pins in duet board 0.6?
by
swaroop
-
Duet
Hi o_lampe
Thanks for advice but I want a Marlin firmware for ceramic 3D printer.
Thanks
Swaroop
by
swaroop
-
General
Hi O_lampe ,
Its actually pnuematic driven of ceramic extruder which had clay in that.
Thanks
Swaroop
by
swaroop
-
General
hi guys,
I want a Marlin firmware for Ceramic Extruder in Cartesian 3D printer. Please help me
Thanks
Swaroop
by
swaroop
-
General
ohh.. !! Thank you
by
swaroop
-
General
Hi O_lampe,
Thanks for the suggestion but if i keep thermistor at hotter side where i can put the heat sink and fan? Please help in this!!
Thanks
Swaroop
by
swaroop
-
General
Hi Tleneel,
I placed peltier module as a cooling bed but when temperature given -4degree centigrade it is not responding and when i give high temperature its going low temperature. I want the temperature to be control or is there any where to invert the logic of mosfet like when the board is ON the D10 pins should give 12v
thanks
Swaroop
by
swaroop
-
General
hi to all,
I want to use cooling bed instead of heated bed. I have a peltier to do but i have to control through marlin and ramps. please help me in this.
Thanks Swaroop
by
swaroop
-
General
Hi Dj,
Thanks for the info.
by
swaroop
-
General
hi Dj,
I am using Arduino mega 2560 mated with Ramps Board so when i connected multimeter to the pins in ramps board where i want to get different output with different inputs. there its giving 0v
Thanks
Swaroop
by
swaroop
-
General
Hi Dj,
I tried with different pins but still the issue is there. i want to get a different voltages when i give different inputs
Thanks
Swaroop
by
swaroop
-
General
Hi Dj,
Thanks for reply. but if i use M42 g code it is not responding like M42 P45 S150 if i give like this it is giving 5v supply to 45 pin. i want as a voltage regulator where i can regulate the pressure by regulating voltage if i give analog input it has to give analog output. please help me
Thanks
Swaroop
by
swaroop
-
General
Hi to all,
I want to connect pressure regulator (0-5v) to Ramps Board and i want to regulate through G codes. please help
Thanks ®ards
Swaroop
by
swaroop
-
General
hi to all,
I want a customised g code button in pronterface so that if i press it has to go on increase by given value. please help me in getting this.
Thanks
Swaroop
by
swaroop
-
General
For Ramps, we have used Arduino Uno to detect the loss of power. When the power is not there, it will send the signal to the RAMPS and it will pause immediately. But, here we are having UPS back up. So, the printer will go to Pause mode, heaters will be switched off.
When the power comes, Uno will send the signal to RAMPS, it will resume the printer. (Heaters will be switched on and it will go
by
swaroop
-
Developers
hi to all,
I have a 3d printer with marlin rc7 and ramps 1.4. in my area am having regular power cuts like hours. I want "auto resume" option so that if power loss i don't worry about the printed part. please help me in getting out of this.
thanks
swaroop
by
swaroop
-
Developers
Hi Robert,
Thanks for the suggestions. As per the previous instructions, my optical end stop was connected to X min and tt worked perfectly. I used X min pins, accordingly I changed it in "pins_RAMPS.h".
Also, in "Configuration_adv.h" we have to un comment the following line:
#define FILAMENT_CHANGE_FEATURE
by
swaroop
-
General
Hi Robert,
Thanks for the suggestions. It worked perfectly. I used X min pins, accordingly I changed it in "pins_RAMPS.h".
Also, in "Configuration_adv.h" we have to un comment the following line:
#define FILAMENT_CHANGE_FEATURE
by
swaroop
-
General
Hi, Please help me in getting out from that problem. As i am using optical sensor and ramps 1.4 board i connected the optical sensor to X_ MAX pins which are the unused pins. I want what are the things i have to configure in marlin firmware. Please help me in coding
by
swaroop
-
General
Sir,
I want to add optical sensor to my ramps 1.4 board and i want to enable filament runout sensor. please help me in this.
Thanks
by
swaroop
-
RAMPS Electronics
