Show all posts by user
Page 1 of 2
Pages: 12
Results 1 — 30 of 45
Hi
I have a problem and I think its a miscalculating of the temperature from the thermistor readings and the thermistor table. I have done some testing of my thermistor and different thermistor tables. With this board and the test program on the bottom of the site I have good readings at room temperature but with teacup I have readings of T:4.0 and when I heat the extruder to 60 degree my therm
by
atztek
-
Firmware - experimental, borrowed, and future
Na das ist ja interssant, ich habe gerade das test programm mit der thermistor tabell mit den orginal werten von Wolfgang aufgespielt und bekomme ganz gute zahlen ( die schwanken etwas um die zimmertemperatur). So mein verdacht liegt jetzt auf der Firmware. Werde mal verschieden Versionen testen.
Tschüss Jörg
by
atztek
-
Altes Forum
Wolfgang danke für den gedanken einfach mein Temperatur Sensor Board nachzubauen. Hab es getan mit hilfe von drei Drähten und einer Lüsterklemme. Ergebnis ist das es die gleichen zahlen wie mein orginalboard produziert. Damit weiss ich zumindest das mein board funktioniert. Der wiederstand meines thermistors ist 111800 ohm bei 21 grad celsius und soll ein beta von 4036 haben laut Wolfgang (hab s
by
atztek
-
Altes Forum
Danke Wolfgang war mir nicht sicher wie genau die sind also das board nochmal auseinander nehmen oder eine andere tabelle benutzen.
Jörg
by
atztek
-
Altes Forum
Ich glaube ich habe ein problem. Nach einigem rumprobieren mit meiner gen2 elektronik habe ich festgestellt das ich den falschen wiederstand in meinem temp sensor board eingelötet hatte. Nach beheben dieses fehlers habe ich die thermistor tabelle von stoffel eingespielt und mit teacup über ein terminal programm ein paar werte abgelesen. Bei raumtemperatur zeigt mir mein board T:4.5 an und wenn ic
by
atztek
-
Altes Forum
I now have a temp reading of T 0.0 , this let me thinking of having not the right temp table so i changed the config.h to DEFINE_TEMP_SENSOR(extruder, TT_THERMISTOR, 0,1)
what gives me a temp reading of T : 534.0
thats very odd to me because its so high and so accurat with no after point numbers.
so what should i do? I will download the last master branch as zip and look for some differenc
by
atztek
-
Firmware - experimental, borrowed, and future
Hi Triffid
I Have made the changes to ThermistorTable.h like you indicated.
Here is my old ThermistorTable.h
And now with the changes it compiles and get uploaded see
Thank you very much
p.s. now i need to test it a little
by
atztek
-
Firmware - experimental, borrowed, and future
Danke Stoffel
Aber könntest du mir sagen wie der thermistor heisst oder einen link zu der thermistor tabellle geben.
Danke
by
atztek
-
Altes Forum
Hi Xfire
Ist der richtige COM 1-4 eingestellt im Host programm und die richtige baud rate?
Sieht wie ein kommunikations fehler aus aber ich kenn mich nicht sehr gut mit dem host aus.
Cu Jörg
p.s. @ Stoffel15 kannst du mir vielleicht deinen thermistor table geben. Ich habe den von teacup probiert und den für EPCOS 100K Thermistor (B57560G1104F) aus dem wiki aber ich bekomme nur 0.75 C bei zimm
by
atztek
-
Altes Forum
Hi
I have downloaded a newer version of teacup in zip format.
As I tried to upload the firmware to my reprap, I had an error. Here is the pic and my confic.h(altered for my machien).
Can you help me and tell me what is wrong in my confic.h.
I use an 328 arduino and gen 2 electronic.
Thank you
by
atztek
-
Firmware - experimental, borrowed, and future
Thank you very much its work now. Now I have to figure out how to build a adjustible z flag so I can home z with different build plats and tapes. BTW wich pin is pin 0 for the thermistor, I gus its analog pin 0 and not digital pin 0.
Thanks Jörg
by
atztek
-
Firmware - experimental, borrowed, and future
I have tried to change the direction of z in home.c no success but as i changed back and blocked the endstop light while tipping in the comand it goes in the right direction and when i unblock the endstop it goes immeditly in the other direction. Next I tried to to uncomment Use_internal_pullups in confic.h but no change in the behavior. All with the g161 z comand.
So how do i invert the signal o
by
atztek
-
Firmware - experimental, borrowed, and future
Traumflug the g1 and g0 commands are working like expected (they go up when i type g1 z10 f1000 or z10 or go z10) and they go downward when I type z0 or g1 z0 or g0 z0. So only g161 dosent work like expected.
Jörg
by
atztek
-
Firmware - experimental, borrowed, and future
When i type g161 z in my terminal. the z axis go in the positive direction but i have no max endstop and when i type 162 z nothing happens. I will wait for a version that will incorporat the endstop branch.
Jörg
by
atztek
-
Firmware - experimental, borrowed, and future
Hi
Are the endstops supported in the current firmware, because I have attached my z min endstop to my machine but I can not home with g28 or reprap host software the axis stops when the soft endstops in the firmware are reached. The signal is on the pin d4 on my arduino duemilanova and its high when the endstop is triggered but the software is not stopping. I use currently the firmware triffid-T
by
atztek
-
Firmware - experimental, borrowed, and future
Elk um zu prüfen ob das lose usb kabel schuld ist an dem aussetzer, einfach mal das usb kabel mitten im druck also 1. lage rausziehen und sehen ob sich dein mendel gleich verhält. Was passiert wenn du das kabel wieder einsteckst könnte auch aufschulssreich sein.
Jörg
by
atztek
-
Altes Forum
Ich hatte mir dummerweise vor ein oder zwei jahren die elektronik bei dem ursprünglichen reprap foundation aus amerika gekauft bevor ich ein funktionierenden roboter hatte. Und in der gen2 elektronik gibt es bloss 3 stepper boards daher meine ursprüngliche anfrage. Beim Grrf habe ich jetzt ein polulo board bestellt für den extruder. Hätte ich damals gewartet mit dem kauf der elektronik bis mein m
by
atztek
-
Altes Forum
Hi
Ich hatte ein paar probleme weil ich die maximale feedrate zu hoch eingestellt hatte in der firmware. Mit meinem terminal program Funktionierte die achse zwar aber bei dem reprap host stotterte der motor dan auserdem musste ich die maximale feedrate im reprap host kleiner einstellen als in der firmware. Weiss auch nicht wieso. Maximale feedrate 3000 mm/min in firmware und 1500 im host sonst
by
atztek
-
Altes Forum
I have read a little more on the wiki and see now I have to use the pwm pin 9,10 or 11 because there signal will only be amplified by the board so ignore my post above.
Jörg
by
atztek
-
Firmware - experimental, borrowed, and future
Hi all
I have a PWM Driver board 1.1 here. Have the pin to drive the pwm board output to be a special pwm pin or can i use every analog pin on my duemilanove board. And which pin you recommend for extruder heater driver over the PWM board.
I hope you understand what I ask for, because english is not my natural language .
Jörg
by
atztek
-
Firmware - experimental, borrowed, and future
Hi Wolfgang
Ich benutze nur das breakout board der gen2 elektronik mit dem arduino drauf und hab dan step und dir leitungen mit den stepper boards verbunden bis jetzt und konnte die mit dem reprap host programm anspechen und meine motoren arbeiten wie erwartet. Also brauche ich bei dem polulo board auch nur Null, Step und dir mit dem breakout board zu verbinden und die pins am polulo für das mic
by
atztek
-
Altes Forum
Hab mir mal ein board bei grrf bestellt nachdem ich mir mal die schematische schaltung und deren erklärung reingezogen habe. Müsste eigendlich an mein duemilanove arduino anschliesbar sein. Danke für den tip dachte immer man bräuchte noch zusätzliche elektro bauteile um die boards benutzen zu können.
Danke Jörg
by
atztek
-
Altes Forum
Hi alle
Kann mir da jemand helfen? Hat von euch jemand zufällig soetwas rumzuliegen, Kann auch ungelötet aber bitte mit allen teilen zum selberlöten sein. Wie viel wollt ihr dafür haben?
Danke Jörg
by
atztek
-
Altes Forum
Ich würde mich da mit 1 motor gerne beteiligen wohne in Berlin. Kann man so einen Motor irgendwie als brief schicken. Wenn nicht schick ihn mir unversichert.
Wie machen wir das mit der bezahlung?
Tschüss Jörg
by
atztek
-
Altes Forum
Thank you Triffid Hunter
Now it works in the terminal. Now I need only a working host program Because the reprap host will not connect to teacup (I know why and I too find the behavior of the programer silly that make it extra incompatible ).
I work on a windows machine, by the way so will try repsnapper and replicatorg .
By Jörg
by
atztek
-
Firmware - experimental, borrowed, and future
Hi
I´m have build my repstrap mechanic and try now to make my electronic and software play nice together. I have a Arduino duemilanove connected to a generation 2 stepper controller 1.2 and a nema 17 hooked up to this. I have verified the electronic works with an example code from here Example code . I have verified 2 pin combinations that work but when i upload teacup to my arduino i can only
by
atztek
-
Firmware - experimental, borrowed, and future
For your information, i now see that my packet is on the way to me. It was shiped 2 weeks after purchase.
by
atztek
-
For Sale
Hi kimberly
I think it must be Jörg May or atztek1. Because i dont know what paypal is using but the delivery adress is showing the name Jörg May.
If you have more question dont hesitate to ask.
Thank you
Cu atztek1
by
atztek
-
For Sale
Hi kimberly
I had bought 2 kits from you on ebay (the "Basic Laser Cut Version for RepRap Mendel Printed Parts" and "RepRap Laser cut Thick Sheet Set "). I had bought them on 1 of may and have not recived a message to confirm the shipment so i dont know is the packet on its way or not. Please tell me when i can expect my parts.
Cu Atztek
by
atztek
-
For Sale
Page 1 of 2
Pages: 12