Show all posts by user
Page 1 of 3
Pages: 123
Results 1 — 30 of 70
i make the software with linux.
and i control the smootieboard under win7 with pronteface ftdi works but also usb.
with usb you have less commands no sd card and no commands like LS /SD/ .
start pronterface now plug in the usb you will see a window pop up with sd card info close this now connect whit prontefase and its online.
reset and sd card in the software is not working with me.
by
michel pet
-
New Zealand RepRap User Group
ok its working.
the problem is the windows software.
i installed Linux and did the same thing and it works.
by
michel pet
-
New Zealand RepRap User Group
i cant upload the file firus problem my pc is clean test it.
led 9 and 1 are burning.
when i run a g code several leds burn.
when i check the voltage of the step and dir and enable the step and the dir are hy and low the enable sty low.
the con fig file is standard.
i cant find the enable setup in the code the ports are ok.
sorry fore my bad english.
and thanks fore now.
by
michel pet
-
New Zealand RepRap User Group
led 9 and 1 are burning.
motors are not online but when i turn 1 motor led 1 gets on and the leds from q8 and q9 licht up.
when i run a g code several leds go on and of.
an with a multi meter i can get the step and dir but the enable is still 0 the step en dir are 3,3 Hy and 0 low so the work ok and the enable is constant 0
sorry fore my bad english.
and thanks fore now.
by
michel pet
-
New Zealand RepRap User Group
i have 3,3 volt at the step and the Dir but the enable is not coming online.
i dont understand this.
by
michel pet
-
New Zealand RepRap User Group
i can reed the tempeture now in pronterface but only in the text after M105 the tempeture has no auto update.
the motor will not turn at all the problem good be the end stop`s?? in the con-fig file there is no option to set them off.
there is no diverseness in power when the 24 volt is on or off it looks like the drives ar not coming online.
by
michel pet
-
New Zealand RepRap User Group
vbb and 5 volt on power now.
the software looks to work ok see lots of leds work when i load a code.
1 motor at the m1 port fore testing.
head bed and head not posible fore now i hope soon.
the motor will not move at al with g gode running leds go on and of so it looks like the code is working.
this is the config file i hope the pins are ok.
alpha_step_pin 2.0
by
michel pet
-
New Zealand RepRap User Group
ok i think i have it running ok now.
in pronto face i can load a code en run it i see several led burning.
i cant see the temperature from the head and the bed.
in the config the head and bed are ok.
a test whit M105 something like that it gives ok and nothing more.
i like a little more info wat to see en wat not.
by
michel pet
-
New Zealand RepRap User Group
i am testing the software under win7 64 bit.
i have the 01.1 software but when i run the win.install it runs but not ok end the rest will not work ok than to.
Wat do i wrong??.
by
michel pet
-
New Zealand RepRap User Group
i am going to test this controller to i like to no how the power supply is working is it usb or do we need the 5 volt input to control the Bord an program the Bord.
by
michel pet
-
New Zealand RepRap User Group
zit er teflon in de kop verwerkt??
zo ja haal dat er dan maar uit en meet de door voer maar eens op ik vermoet dat aan het heten deel het gat een stuk kleiner is geworden.
als dit het geval is een nieuw stuk teflon er in plaatsen.
teflon zet uit als het heet wordt en kan geen kant op om dat het ingesloten zit en alleen naar binnen kan en je materiaal loopt dan vast.
by
michel pet
-
Dutch User Group - Archive
cnczone.nl daar is veel info te vinden en loopt erg lekker daar dus wie info zoekt of vragen heeft zie link.
by
michel pet
-
Dutch User Group - Archive
bigger mosfet and not on the ramps itself is the best way.
i have made this and set the port fore the fet to 1 of the servo ponts and it works ok.
[4.media.hyves-static.net]
by
michel pet
-
RAMPS Electronics
use the power plug no diode an it works ok.
i use a step down from 24 volt to 9 volt now its not to hot on the arduino.
lcd and sd work ok.
i run the set on 24 volt and 12 volt fore the bed but with a separate fet so the Bord gets no 12 volt 30 amps.
by
michel pet
-
RAMPS Electronics
it is pwm controlled.
by
michel pet
-
General
i need to tape it under here.
by
michel pet
-
General
Wat kind of tape wood be the best fore the head bed.
i want to stick it under a alu bed
by
michel pet
-
General
this is the schema .
a have made a test print and it works fine.
a have set the pin from the head bed to pin 5 this is a servo pin and ik works .
by
michel pet
-
General
15 and 20amp is to much fore the ramps so i think we need make it separated of the ramps Bord.
pin7 pwm is not used on the ramps i think.
like this id.
by
michel pet
-
General
12V to the input pin its not possible in my setup i test the wires and no problems.
i think thunderstorms did it.
by
michel pet
-
RAMPS Electronics
Page 1 of 3
Pages: 123