That board only has 512kb of flash so the firmware won't fitby jay_s - Firmware - experimental, borrowed, and future
have you got this fixed? which drivers are you using?by jay_s - Firmware - mainstream and related support
you would have to cut down features from the firmware as it won't fit on an STM32F1by jay_s - Firmware - experimental, borrowed, and future
@karabas SPIby jay_s - Firmware - experimental, borrowed, and future
Is it open source? If so, where can we find the firmware fork etc?by jay_s - Developers
Its listed on the wiki. Teamgloomy.github.ioby jay_s - Firmware - experimental, borrowed, and future
Its servo0 I thinkby jay_s - Firmware - experimental, borrowed, and future
It only receives data during a printby jay_s - Firmware - experimental, borrowed, and future
Just use the servo. You can use either the name or pi number to refer to it as both are supportedby jay_s - Firmware - experimental, borrowed, and future
in that case, it has to be a pin that starts with 0 or 2. 1.26 won't work as it can't driver interruptsby jay_s - Firmware - experimental, borrowed, and future
What filament sensor are you trying to add?by jay_s - Firmware - experimental, borrowed, and future
I should also point out that it's now managed by gloomyandy.by jay_s - Firmware - experimental, borrowed, and future
It does exist.by jay_s - Firmware - experimental, borrowed, and future
@diman77 There won't be a further 3.1.1 release. 3.2 RC1 should be released in a few days time. I would suggest moving to that as its fairly stableby jay_s - Firmware - experimental, borrowed, and future
Do your heated bed wires run anywhere near the raspberry pi cable? It's probably interference from those Best to join the discord channel as it's easier to support on there.by jay_s - Firmware - experimental, borrowed, and future
The M5 board is supported as of 3.2 Beta 2, allowing up to 11 drivers to be used.by jay_s - Firmware - experimental, borrowed, and future
@ghent360 The source has been released at RRF 3.2 beta 1 has also been released atby jay_s - Firmware - experimental, borrowed, and future
You can't yet as it hasn't been released. It will be, it just needs further work firstby jay_s - Firmware - experimental, borrowed, and future
That's great news. Glad you got sortedby jay_s - Firmware - experimental, borrowed, and future
Yes, it should work as wifi works. You'll need to perform the hardware modification as detailed here Most of the settings are the same, you just don't need to include 8266wifi.espDataReadyPin or 8266wifi.espResetPin in your board.txt file Prepare the wiring (e.g. resistors etc) as per hereby jay_s - Firmware - experimental, borrowed, and future
You probably used pronterface or octoprint to send the M587 command in which case, the password will have been converted to uppercase. From the wiki... If you are using pronteface, it will convert all text to upper case, in which case, if you wanted to use “PassWord”, you would write P”P’a’s’sW’o’r’d” with the ‘ indicating the following letter should be lower caseby jay_s - Firmware - experimental, borrowed, and future
Not at the moment. The whole firmware for the ESP would require porting. I'm not aware of any plans for this to be done for the Duet range of boards eitherby jay_s - Firmware - experimental, borrowed, and future
The expansion board is not currently supported I'm afraidby jay_s - Firmware - experimental, borrowed, and future
I would go for something higher like 1by jay_s - Firmware - experimental, borrowed, and future
You could increase the blip time. That's the B value.by jay_s - Firmware - experimental, borrowed, and future
spegelius good to hear another user with it working on the MKS Sbase. What are your loading times like on the first load of DWC? And you won't be able to use the MKS tft Wifi-module as thats an ESP-01 and doesn't have enough pins etc. The NodeMCU or Wemos Mini are the recommended typeby jay_s - Firmware - experimental, borrowed, and future
A new thread has been created for the gloomyandy variant of RRF. From now on, please direct all queries to that thread as this one will only be used for sdavi's version. Support for gloomyandy's version can also be obtained through discordby jay_s - Firmware - experimental, borrowed, and future
are you going to do the same for the 3.1 branch (the current release) and the 3.2 branch (the next release)?by jay_s - Firmware - experimental, borrowed, and future
Join us on discord it'll be easier to be able to troubleshoot with youby jay_s - Firmware - experimental, borrowed, and future
well you've got something wrong somewhere are your board.txt file is not being loaded. Can you show the contents of your sd card?by jay_s - Firmware - experimental, borrowed, and future