Show all posts by user

Re: RepRapFirmware 3.0 port for LPC1768/9 based boards - 4 years ago

Quotekostasbmw hi just received the lpc board for my skr 1.4 for the rep rap conversion and i m looking for a tutorial of how to...... thanks

by weed2all - Firmware - experimental, borrowed, and future

Re: RepRapFirmware 3.0 port for LPC1768/9 based boards - 4 years ago

so for setting up the uart of tmc2208 i need to put the jumper on uart as when use with marlin and add this line "stepper.numSmartDrivers = 4" to board.txt

by weed2all - Firmware - experimental, borrowed, and future

Re: RepRapFirmware 3.0 port for LPC1768/9 based boards - 4 years ago

thank you for your fast response...it was actualy my fault...i wire everything but somehow i forget to add the 2200r resistor between ground and reset pin and thats why didnt work...i gone thru wireing everything again and seen that 2200r resistor was left out of wiring...boomer now is working as it should actualy no stepper drivers were installed just because i was only testing before wire ever

by weed2all - Firmware - experimental, borrowed, and future

Re: RepRapFirmware 3.0 port for LPC1768/9 based boards - 4 years ago

Quotegloomyandy Please post... * A picture of your board and WiFi module so we can see how you have it set up. * The contents of your board.txt file * The output from M122 P200 Have you flashed the WiFi firmware to your WiFi module? What stepper driver modules are you using, they are currently all reporting errors. thank you for your fast response...it was actualy my fault...i wire everything b

by weed2all - Firmware - experimental, borrowed, and future

Re: RepRapFirmware 3.0 port for LPC1768/9 based boards - 4 years ago

hi guys, i must do something wrong because i cant connect to my wifi...im using yat to setup my wifi network, but i cant figure out why it cant connect,i send M552 S0, after that i send M587 S"wifi ssid"P"password" and it disconnect from yat. i folow the intruction from gloomyandy github, i wire my nodemcu v2 to skr1.3 folowind the instruction, i create the sd card files as per instructions, i ad

by weed2all - Firmware - experimental, borrowed, and future

Re: Arduino DUE + RADDS + TMC2208 UART - 5 years ago

Hi...so what is the current state of this?

by weed2all - Firmware - Marlin

Re: Trouble configuring 3d touch z probe - 6 years ago

You have to connect the 2 pins of 3d touch to GND and Sig on Zmin...

by weed2all - Firmware - Marlin

Re: Arduino IDE search all of sketch - 6 years ago

You have all other files in src folder under marlin...

by weed2all - Firmware - Marlin

Re: Trouble configuring 3d touch z probe - 6 years ago

See this post...

by weed2all - Firmware - Marlin

Re: Trouble configuring 3d touch z probe - 6 years ago

Let me see

by weed2all - Firmware - Marlin

Re: Arduino DUE + RADDS + TMC2208 UART - 6 years ago

This is the pins_RADDS.h Where should I put the pins for tx and rx? Should I create a new line for each axis with #define X_TX_PIN ... #define X_RX_PIN ... Where ... Is the pin number that I want to use?

by weed2all - Firmware - Marlin

Re: Arduino DUE + RADDS + TMC2208 UART - 6 years ago

Ok...so where do i need to change the pins...in marlin 2.0, under pins_RADDS.h? I will use the available pins from max endstop,or from lcd connector that is on radds...because i don't planing to use lcd...or if i will use lcd...i have the aux1 pins available as well..that aux1 pins on radds is for adding the extra extruders with the expansion board v2 or v3 so my question is that i have to activ

by weed2all - Firmware - Marlin

Arduino DUE + RADDS + TMC2208 UART - 6 years ago

Hi all...im new here and I bought a RADDS Shield for arduino DUE and a couple of tmc2208 from waterrot...my question is how can I use the tmc2208 drivers in uart mode...i will use on X Y Z axis and for 2 extruder I will use lv8729 or a4988 drivers.. I'm searching on Google few days now to try to find an answer but I didn't find anything

by weed2all - Firmware - Marlin