Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 21 of 21
With the firmware-wifi 3.1.1-6 on the command M122 the web interface restarts, while the printer itself works fine. Perhaps the output of the command is too large.
In the browser console I see that the answer is "buff: 255"
by
bcmob
-
Firmware - experimental, borrowed, and future
Two days I print with a physically disabled TFT and everything is fine. There were two long prints over 4 hours and all the rules.
I’ll test it again, if everything is fine I’ll try to connect the TFT but I’ll take the power separately. Or I’ll increase the polling interval "M408 S4" in the screen.
firmware-wifi.bin RRF3.1.1
by
bcmob
-
Firmware - experimental, borrowed, and future
When printing after 1 hour 43 minutes, printing suddenly stopped and the printer rebooted.
firmware-wifi.bin RRF3.1.1 SKR1.3 TMC2209 ESP8266 TFT24
Status immediately after reboot
M122
=== Diagnostics ===
RepRapFirmware for LPC176x based Boards (biquskr_1.3) version 3.1.1 running on LPC176x at 100Mhz
Used output buffers: 3 of 16 (13 max)
=== RTOS ===
Static ram: 3876
Dynamic Memory (RTOS Heap 5)
by
bcmob
-
Firmware - experimental, borrowed, and future
Thanks for the low voltage idea.
The ESP turned out to be nothing to do with, even its complete shutdown did not help.
Turning off the TFT screen helped. I will think how to fix the problem.
It is surprising that on older versions there is no such problem. Looks like the controller is loaded there later and the screen is already running by then. )
by
bcmob
-
Firmware - experimental, borrowed, and future
https://youtu.be/W25N7L_A1dY
M122
=== Diagnostics ===
RepRapFirmware for LPC176x based Boards (biquskr_1.3) version 3.1.1 running on LPC176x at 100Mhz
Used output buffers: 3 of 16 (10 max)
=== RTOS ===
Static ram: 3876
Dynamic Memory (RTOS Heap 5): 2648 free, 2624 never used
Exception stack ram used: 352
Never used ram: 332
Tasks: NETWORK(ready,632) HEAT(blocked,1360) MAIN(running,1460) IDLE(re
by
bcmob
-
Firmware - experimental, borrowed, and future
All right
Newest Versions
SKR 1.3, ESP8266, tmс2209
During these 2 minutes, the hot-end fan starts and stops constantly. It is connected to HE1. Also, if you connect to the computer, the device "serial" then appears then disappears. Then everything starts and works fine
by
bcmob
-
Firmware - experimental, borrowed, and future
When using "firmware-wifi.bin" versions 3.01 RС11 and older, the printer strates for 15 seconds. Starting from version 3.01 RС12 and newer, the printer for two minutes in a cyclic reboot and then normally starts and everything works. What could be the problem?
by
bcmob
-
Firmware - experimental, borrowed, and future
Quotejay_s
Does it look any different to the standard touch interface?
The standard touch interface does not work through the AUX as there is no confirmation of commands and works differently unlike the MARLIN standard
by
bcmob
-
Firmware - experimental, borrowed, and future
Here is my modification of the firmware for the TFT screen.
Connect to AUX.
Tested for BIQU TFT24_V1.1. So it should work on the other TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1, MKS 32
github.com
by
bcmob
-
Firmware - experimental, borrowed, and future
In this case, a huge request to implement full-fledged work through AUX, so that you can use cheap BIQU TFT24 / TFT32, MKS-TFT panels for control. Now through AUX we get the answer only in json on the M408.
Here is the patch that sdavi did Option for aux serial to output responses with compatibility mode for RRF2
by
bcmob
-
Firmware - experimental, borrowed, and future
I launched on SKR1.3 https://github.com/gloomyandy/RepRapFirmware/releases/tag/LPC_RRFv3.01RC5 firmware.bin with TMC2209 drivers and screen 12864. It seems that everything works. But I still need wifi through esp8266. In the firmware firmware-wifi.bin screen 12864 does not work. What should I do? Is it possible to simultaneously run "tmc uart", wifi and the screen?
by
bcmob
-
Firmware - experimental, borrowed, and future