Show all posts by user
"Does not run correctly, it does not move to the destination point." is not very precise. If I need a chance to find a problem on a system I do not have I need more data. What commands get issued and what moves get executed? Which distances did it make in reality in which direction? Only with soch data I can make up a theory to compare with code.
by
repetier
-
Repetier
I meant the firmware. Homepage should now work reliable.
by
repetier
-
Repetier
Read my post!
RAW1 is your bed. Update to latest version and you will get RAW0 for your extruder.
by
repetier
-
Repetier
RAW1 is for your bed since you have 1 extruder. RAW0 is for extruder but I just saw that only for > 1 extruders the raw values got output. I have fixed that for the next update.
@ are the PWM output levels. B@ is for bed.
by
repetier
-
Repetier
Yes, since Host 1.5.0 and Server 0.65 this works very good.
by
repetier
-
Repetier
I see. Only tested 1 and 4 extruder, not 2 where you get your error. Is now also fixed.
by
repetier
-
Repetier
It was a missing exception for a new feature. Should now also compile for you in the new version.
by
repetier
-
Repetier
What I see is that you are using Marlin not Repetier so you can forget anything I said. Maybe just wrong wiring. Can happen if only one coil gets current in motor. Otherwise try a marlin forum if it is firmware related.
by
repetier
-
Repetier
Adding a submenu to a submenu is the same as in the main menu. Define a line referencing it and add it and increase entry count by 1 (the count lines).
The new submenu has similar code like e.g. quick menu. Just copy the logic.
Remark: New version now uses changeable translations. So all menu entries having translateable entries have now _T appended. The old version with directly included text
by
repetier
-
Repetier
Check eeprom values for steps/acceleration etc.
With 499°C the firmware should mark the sensor as defect and prevent extruding if you haven't changed the defect values to wide outside the range.
With M302 S1 you can enable cold extrusion so you can test at room temperature or just by faking a sensor with 100kohm resistor.
by
repetier
-
Repetier
"check commands send" = Read log what gets send to your printer. If it is a plain move the reason is in firmware/hardware and since all hosts do the same I think it is. But then this is the wrong forum.
by
repetier
-
Repetier
Check commands send! I guess it sends correct commands and firmware/printer hardware causes this. Why is not really clear to me except if you have autoleveling enabled. There if you have big skew moving one axis will always move the others a bit.
by
repetier
-
Repetier
Please redownload again. I think I have fixed the problem.
by
repetier
-
Repetier
It is not the selected color you see, that is only the frame around it. You search for extruder color in printer preferences. Set color for extruder 1.
by
repetier
-
Repetier
Wizards are pages where you can listen to next/previous and ok events. So you have to decide how you want to do it. Simplest is to have 4 pages - one for each point and for each "ok" action you do
popMenu(false);
pushMenu(&ui_wiz_jamwaitheat, true);
to switch between pages and also move to next point.
mtype is menuType whcih is set to 5 = WIzard page. Defines how th
by
repetier
-
Repetier
I mean if response to M105 changes format (again) it may be unparsable for a host version and then it can not control if temp. is reached. That hopefully never happens, but I have no influence on firmware developers and what they do. And the host would ignore things like stabilize time and temp. corridor which you could set in firmware. I personally set these always to 1s so no problem for me, bu
by
repetier
-
Repetier
On the other side if firmware changes temp. response it does suddenly not work any more and you loose all settings for temperature handling like how long you want to be inside a corridor.
I see this would be nice to improve speed of response everywhere, but it is by no means an error but defined behavior.
by
repetier
-
Repetier
Some commands block the printer communication for a while. These are normally at the start of your gcode for heating up extruder and bed. These only return when target temperature is within some bounds for a time set in firmware. These are M109 and M190. Until then no more communication occurs.
by
repetier
-
Repetier
Are you talking about the blue line to the left? I thought your extruder is not stopping when you print.
by
repetier
-
Repetier
Yes, but what was th e E position before that command. -100, -65, 882 ? It is not defined so random results can be expected. Especially if it is the second print.
by
repetier
-
Repetier
You see percentage of the PWM output reported by firmware. So 100 is always on, 50 is 50% on. In firmware you limit these values with paramers having " max pwm" in it's name, depending on firmware.
by
repetier
-
Repetier
Not sure what you want to say, but befor
G1 E10 F160 ; estruder 10mm for pressure nozzle
you also need
G92 E0
or it is not clear from what position you want to go to E10
by
repetier
-
Repetier
Do you see COM3 in printer settings if you open port selector? That means the port is there and working (assuming it belongs to your printer).
Leave protocol on autodetect and then try different baud rates until it succeeds.
If you could select com and get a error message you have most probably a different software using the same port. Could be repetier-server if you configured it to use the pri
by
repetier
-
Repetier
Yes, that is in deed a problem with CuraENgine. You send all stls as commandline and thus curaengine starts with T0 always. For slic3r we could solve that problem in 1.5.6. Only problem here is the limit of 3 extruder for slic3r in the host. Need to upgrade this now slic3r can handle it.
by
repetier
-
Repetier
Die Zeitberechnungen sind immer Schätzungen und beim Druck wird von der Zeit die berechnete Zeit abgegezogen und die differenz ist die Restdruckzeit. Daher korrigiert die sich zum ende hin immer, so das sie immer passt.
Host rechnet 100% Geschwindigkeit + Aufschlag aus druckereinstellungen.
Server nimmt Beschleunigungen, buffergröße Heizgeschwindigkeit aus der Konfiguration (bei repetier-firmwa
by
repetier
-
Software
There is a bug making server ignore commands followed with ; without a space before it, like you wrote for bed off command. So add a space there.
We are also planning to release 0.65 today where the bug has been fixed.
by
repetier
-
Repetier
Set case light pin to that output pin and enable case light.
by
repetier
-
Repetier
No, I now chmod the curaengine executable.
by
repetier
-
Repetier
0.92 has a feature called heater decoupling. That will shut down all heaters if extruder does not heat up while powered.
You also can set min/max temperature inside temp area. If temp outside is measured it is taken as short/missing thermistor killing temperature also.
You should also enable watchdog so firmware resets if the the temperature manager does not get called regularly.
There is no a
by
repetier
-
Repetier
You can rerun any time. Superuser is not required. It uses sudo to gain root privileges when required. Requires sudo to work!
Please redownload 1.5.6 - I have added a chmod to make it executable.
by
repetier
-
Repetier