I have been hoping to do this so that I can make use of my steppers with lead screws built in but mine have m8-8 acme thread so I have no need for a coupler or any of that but I had not been able to do that until I found this thread thank you very muchby broncosis - General
servo free auto bed leveling for a prusa here guys this is what I have come up with for my auto bed leveling with out a servo for the few of us with out a rampsby broncosis - General Mendel Topics
Ludara. Are your switches normally open or normally closed I noticed issues with my normally open switches once I changed them to normally closed things seemed to work better I am pretty sure The logic has some issues with setups that are not quite normalby broncosis - General Mendel Topics
well after much struggling I have this working on a sanginololu with no servo the real issuse is the math for the offset and the bed locations as it turns out if you go beyond any of your soft limits there is trouble after re reading this thread again for third time I found it on page 3 I hope this helps someone else thank you everyone for all your posts and re read this thread as you woby broncosis - General Mendel Topics
check into Van-Isle-Rapid-Prototyping and the revolutionprinters peopleby broncosis - Canada, Vancouver RepRap User Group
so when I enable bed leveling the only home switch that works properly in my y switch x and z both move away from the home in switch almost like as though they are not even hooked up so after relocating and changing my n/o switches to n/c I have reasonable behavoir how ever if I run g28 then g29 it seem to be forgeting that the probe and the hotend are offset and trys to run off the end onby broncosis - General Mendel Topics
alright guys I am having a wierd ting happen I am atempting a semi manual auto leveling with a jig and a switch much like the kossel on my prusa I am using a sangionlolu with a 1284p in it but once I enable auto leveling my z moves up when ever I home it rather than down as I would like anyone have any ideas when I run a g29 my z just moves up at each location I may have found my issuse hoby broncosis - General Mendel Topics
I ran mine at 19v for a little seemed to be ok but I went back to 12v as the atx power supply was more versitileby broncosis - Sanguino(lolu)
I did this with a simple 2n2222a transistor here is the post I made about it in my local group if you need more info just send me a pmby broncosis - Sanguino(lolu)
they why trust any 2 bricks in a wallby broncosis - General
hey I am looking to find a couple of steppers my z axis seems to skip a few here and there hoping some better motors will workby broncosis - Canada, Fraser Valley B.C. RUG
No just the electronicsby broncosis - Canada, Edmonton RepRap User Group
ok everything is here I am going to try and get a few thing going asap guys sorry about the wait I wasn't planning on stuff taking this long to get here I am jumping on it nowby broncosis - Canada, Fraser Valley B.C. RUG
I wont be able to make it but on a side note I got the last of the stuff to start assembing parts for you guysby broncosis - Canada, Fraser Valley B.C. RUG
um the place I found metric stuff at in abby was the parts desk at avenue equipment but sabre or radier or fastenal can get it for youby broncosis - Canada, Fraser Valley B.C. RUG
I ordered it online Rp is a pain to get to during the week for me I work almost 12 hours a day and I commute in the the company van but it should be here anytimeby broncosis - Canada, Fraser Valley B.C. RUG
well I will do as much testing as I can I have a pursa waiting for electronics too so I will be able to do a little testing but if your in a rush I can smack a untested one up once the solder paste gets hereby broncosis - Canada, Fraser Valley B.C. RUG
hey guys sorry I wont be there but I have good news most of the parts are here just waiting on a few alegro's and my solder pasteby broncosis - Canada, Fraser Valley B.C. RUG
Do you have your electronics yet I have a bulk buy going In the Fraser valley rug I could ship you one when they are readyby broncosis - Canada, Edmonton RepRap User Group
Hey guys I am going you have a extra couple of sanguinololu boards So if any of you guys on the fence want in last call I order the last of the parts Or if you know anyone put the word outby broncosis - Canada, Fraser Valley B.C. RUG
That's a shame I could have saved you the 20 in in shipping and a little on bulk purchasingby broncosis - Canada, Toronto RepRap User Group
Hey I am putting some together I can do the assembly as well but if you just want parts I can do thatby broncosis - Canada, Toronto RepRap User Group
I used to drive one. one of them is still parked out frontby broncosis - Canada, Vancouver RepRap User Group
Well I still have a couple of boards Not spoken forby broncosis - Calgary
I won't be there guys stuff came upby broncosis - Canada, Fraser Valley B.C. RUG
hey have a look at electronics I can help keep the cost down a littleby broncosis - Canada, Vancouver RepRap User Group
I could maybe but what about a2a printer they are in canada and they show more stock than ultimachineby broncosis - Canada, Fraser Valley B.C. RUG
electronicsby broncosis - Canada, Toronto RepRap User Group
I am not in Toronto but I am running a bulk buy on Electronics Sanguinololu boards assembled or kits And step sticks Just check the Fraser valley rug for details I am on my phone or I would post a link Shipping is extra but I can work that out on a person by personby broncosis - Canada, Toronto RepRap User Group
Ok guys just a heads up the bare boards shipped and should be here Soon so I want get the sanguinololu boards sold So far I have 8 of 10 step sticks spoken for And only 3 of 10 sanguinololu boards Plus A couple of extra partsby broncosis - Canada, Fraser Valley B.C. RUG