Quotescottybfg I'm going to say it might be firmware related, maybe you selected the wrong resistance for #1. Here is my fw, some weeks ago it was working Marlin of course #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 #define TEMP_SENSOR_2 -1 #define TEMP_SENSOR_3 0 #define TEMP_SENSOR_BED 1 The firmware should be fine... (it's a standard _chinese_ Volcano with an NTC thermistor). __ Quoby davidmonten - General Mendel Topics
Hi everyone I'm mounting two E3D extruders but when I read the temp it's not the same: it reads 24°C on the #2 (actual room temp) and 41°C on the #1 (both cool) ...and 19°C if I disconnect the #1 I tried to connect another thermistor and it reads 41°c too. note: Before to achieve this the temp on the #1 was 0°C and I've found that one of the small PTFE sleeves protecting the wires near the sensby davidmonten - General Mendel Topics
problema risolto cambiando firmware.by davidmonten - Elettronica e meccanica
Problemi di comunicazione con l'host (Repetier), tanto per cominciare non mi legge il tempsensor e mi da anche un errore di start. Ho aperto un topic in merito, ti lascio il link perchè a ripetere tutto ci vorrebbe un po'by davidmonten - Elettronica e meccanica
Sto avendo qualche problema con una megatronics3. Continuerò a sbattermici ma sto cominciando a prendere in considerazione delle alternative e volevo chiedere a voi consigli. La scheda andrebbe montata su una leaprog creatr dual che ha tutta l'elettronica a 24V. Cercando sui soliti siti cinesi ho trovato la SmotieBoard e la Robin. Qualcuno le conosce? Le consigliereste? Altri modelli, magari conby davidmonten - Elettronica e meccanica
Quote Comincia a mettere solo un hotend senza bed... E vediamo cosa dice. Metti su T0 E non misurare la resistenza sul connettore quando è attaccata, ma misura la tensione ai capi! Ho letto solo ora la tua risposta. Cosa ho fatto nel frattempo: - ho messo il termistore dentro la sua sede assieme a uno o due mm di cavi isolati col teflon. Adesso misurando la resistenza con il tester risulta isby davidmonten - GCODE, Software e Firmware
La leapfrog ha tutta l'elettronica a 24V. Verifica che la Ramps supporti quel voltaggio, mi pare che vada a 12V, sicuramente devi usare i DRV8825 da 1/32, non gli A4988 da 1/16 (non erogano abbastanza corrente).by davidmonten - GCODE, Software e Firmware
si, è lo stesso pinout che ho io (src/boards/703.h). Il sensore funziona, se lo tengo tra le dita la resistenza scende (letta col tester), è solo una questione di corto che devo isolare anche se non capisco come dal momento che il teflon sembra coprire tutto il cavo fino ad arrivare al "cavallo" del sensore...oltre non va. Resta il fatto che il fw non lo riconosce e repetier resta a 0. Vediamoby davidmonten - GCODE, Software e Firmware
I fili der sensore sono dentro del teflon e sembrano ben isolati...sembrano! Se lo tiro fuori dall'heater block il valore torna corretto (148 su 200k...diciamo che è corretto), se stringo la vite di ritenzione torna a 0, cioè va in corto. Provo a collegarlo alla scheda fuori dall'heater (mentre legge 148 su 200k) ma repetier legge 0° per il primo estrusore e 100° per il secondo (tondi e stabiliby davidmonten - GCODE, Software e Firmware
Grazie Mago Volevo fare il test perchè Repetier non mi legge il termistore (temp 0 con MINTEMP 5); Scheda Megatronics3, estrusore e3dv6 clone collegato ai pin T0 e T1 (doppio estrusore, stesso problema); nel fw ho impostato il valore 5 (100K thermistor - ATC Semitec 104GT-2) ma a sto punto mi sorge qualche dubbio... come posso verificarlo? se misuro la resistenza del sensore su scala 200ohm iby davidmonten - GCODE, Software e Firmware
Salve a tutti sto smanettando con MK, se lo compilo normalmente finisce la compilazione e lo carica pure. Prima di dare fuoco alle polveri volevo fare un test ma se abilito #define FIRMWARE_TEST non compila dandomi il seguente messaggio d'errore: sketch\src\fwtest\firmware_test.cpp: In function 'void FirmwareTest()': sketch\src\fwtest\firmware_test.cpp:352:16: error: 'prepare_move' was not dby davidmonten - GCODE, Software e Firmware
Salve a tutti per via di un guasto alla scheda leapfrog mi trovo a doverla sostituire. vorrei montare una megatronics. ho letto un bel po', ho scaricato il firmware per la scheda dal wiki, il firmware originale per la machina dal sito leapfrog, un firmware custom sviluppato da outbound che però non era stato testato sulla macchina. Tenendo tra parentesi le questioni relative ai parametri comeby davidmonten - GCODE, Software e Firmware
WOW! I've swapped fpos_t with filepos_t in all the files to avoid libraries conflict and it compiles! Anyway it gives me some errors about ultralcd.cpp, something (classes?) that has been redefined. But now it's compiled I've just to invert Y and Z motor pins It's a little satisfation.by davidmonten - General
Thank you very much for your help I'll be supershort. same errors when compiling; I've not changed the motor pins, I've just open and compiled. I've made a second attempt after a libreries update but I've got the same error. I do not have such a good coder skills (coders may kill me for this istance xD) so I'll try to understand what errors message means trying to debug it (like a butcher woulby davidmonten - General
Goooooooodmorning Vietnaaam! I'm David and I'm a not-so-happy-but-still-happy possessor of a Leapfrog Creatr and I'm looking for some help replacing the board. I've had a look around but I don't know if this is the right section to post. Feel free to move the topic or edit the title Before to write here I've searched on the forum for similar topics looking for "megaronics" and "creatr". Here iby davidmonten - General
How may I set an endstop as an optical endstop?by davidmonten - General