am no expert and know even less about the inner working of repetier. But am wondering if what you describing is an issue off switch debounce, on the end stops when homing.by jinx - Reprappers
think about others here who may have a similar issue in the future if people start deleting post because they found a solution how would this help others' we could end up answering/solving the same issue over and over.by jinx - Reprappers
aint there a command that's needed at the end of the g code to shut the bed off. I use a ramp and that never turns off until I tell it tooby jinx - General
or two bowden! am planning on this setup with a couple e3d v6 clones from ebay, not expecting a speed increase , but I am expecting to reclaim some z height on prints, just need to mod a carriage like thisby jinx - General Mendel Topics
hi QuoteVREF's are set at X=0.550v, Y=0.621v, Z=0.542v, E0=0.575v. those seem a little high compared to the 0.40 most set, "WHEN EVER I CHANGE THE POT SETTING TURN THE POWER OFF to the ramps. then adjust. in the marlin firmware: find this line Quote#define DEFAULT_AXIS_STEPS_PER_UNIT {101.82,101.44,2611.20,640} // default steps per unit should be around line #482 " could be you needby jinx - General Mendel Topics
something not right, a Jhead will print for hours at least 4 "enough to print that part." before issues of heat creep. QuoteThe filament passing through the extruder is getting hot and clogging. if filament getting hot in the peek on start up or within 20 min of starting then I check the thermistor and setting. check the retraction setting in your slicer program.by jinx - General Mendel Topics
hi, I went through a similar issue with a new ramps+mega but i used Pololu instead and it worked.by jinx - General
first option be use rafts and support , maybe next use the latest slic3r split the model in half " if the print lifts, it leave gab in the side of the head" downside to the split,by jinx - Reprappers
I use sketchup 8, another plugin I find useful is "solid inspector" very handy. then I export an stl file to netfabb to check. with netfabb you can convert and export 3ds. files which then can be imported into sketchup.by jinx - General
am not sure if this is any use for the discussion but it make an interesting read on modifier meshes with slic3r not tried it myself yet so cant say to much about it.by jinx - General
WHY is this tit IPnot blockedby jinx - General
hi why not go for the mk3 aluminium heat bed, flip it over and print directly on it " using a bit kapton tape for PLAby jinx - General Mendel Topics
while running my printer using pronteface and I open IE9 the printer will pause for like 30 sec, just wondering if other are noticing this.by jinx - General
Quotelepes PLA will obstruct your v5 hotend frecuently that not right, I print with both the v5 and v4 with PLA at 200C no problems at all, you leave it standing for ten minutes then you MAY get a jam.by jinx - General
could this be a diode issue?, our both diodes soldered on the rampsby jinx - General Mendel Topics
what you using to slice the object,, slic3r will allow you to break a set of parts up ,nettfab may as well but i never used it for thatby jinx - General
CONGRATS on your first commission , happy printingby jinx - General
my apologies pushthebolder I lead you on a merry dance with the pins.h file just flashed my ramps without setting pins.h " first time without"..by jinx - General
QuoteNever had to change pins.h for my i3 with RAMPS 1.4, just the Configuration.h thanks for clearing that up steve, i built i2 always manual adjusted the pins.h thought that was the norm,, we live and learnby jinx - General
m302 will allow cold extrusion i thinkby jinx - General
how you getting onby jinx - General
well am waiting for DUST to dust off his crystal ballby jinx - General
QuoteWTF... 1) ignore jinx. he is leading you completely astray. so you sayin we dont need to make the relevant changes to pins.h about which mega in use or which ramps set up to use. is that right Dustby jinx - General
could we make extruder fan come from D9 " is the print cooling fan by defalt now we on to the hard stuff back to the config.h fileby jinx - General
scroll dwn to line 465 "* Arduino Mega pin assignment" and change it so it looks like Quote/**************************************************************************************** * Arduino Mega pin assignment * ****************************************************************************************/ #if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBby jinx - General
ok step back download it again, in download you see Marlin-marlin " extract that file to desktop once in the desktop open the marlin-marlin > marlin , you should see all the files scrol dwn till you see the marlin next to the Arduino symbol click that " fingers crossedby jinx - General
its not you i just downloaded it and opened all i get is the marlin file like you and nothing elseby jinx - General