Hi Mike I did RepRap of acrylic, using acrylic 3 mm, 6 mm and 9.5 mm, all works good. I think 5 mm instead 1/4" (6.35mm) not good idea, better to glue acrylic 3 mm parts in 2 layers. Some parts from Tech Zone Remix have issues: standard NEMA 17 motor Z-axis is not included between the two 8 mm rod, to resolve this problem I redesign some parts. Alexeyby AlexeyShokarev - General Mendel Topics
Wade, davmj thank you! I resolve the problem. The firmware was configured to use the variable resister to set the value by default. I tried to adjust the current stepper motor by variable resistor, but this does not solve the problem. To resolve the problem I did the following: 1) Too sharp notch in the flow bolt, leading to clogging of the bolt notch chips ABS after printing one or two smalby AlexeyShokarev - General Mendel Topics
AlexeyShokarev Wrote: ------------------------------------------------------- > Сейчас бьюсь с экструдером > - использовал Wades Geared Nema17 > Extruder, проблема в следующем: > при начальном запуске нить > ABS формируется (10 - 20 см > диной), но затем > практически сразу подача > прекращается. Разборка > показывает, что при 235 > градусах подающий вал > экструby AlexeyShokarev - Russia RepRap User Group
Wade, I think you're absolutely right. First I used standard extruder nozzle from M6 rod and extruder stops after 30-40 second of work because of melting the plastic rod in extruder, to resolve this problem I installed fan from computer videocard, but problem not been solved completely. After I was used Geared extruder nozzle, the problem with melting the plastic rod in extruder was solved. Myby AlexeyShokarev - General Mendel Topics
I use Wade's Geared Nema 17 Extruder (http://www.reprap.org/wiki/Geared_Nema17_Extruder) with Geared extruder nozzle (http://www.reprap.org/wiki/Geared_extruder_nozzle), RepRap host software and white ABS. I changed the temperature to 235, all other settings standard for RepRap host software. The result can be found in the attached file. I think I need to change some settings by extruder, but dby AlexeyShokarev - General Mendel Topics
Ну если 2-4 недели ждать нехочется, прямая дорога в любой нормальный магазин электроинструмента, там продается пластиковая нить для газонокосилок в бухте, в нашем магазине DWT например есть 2; 2,4; 3 мм, подобрать температуру экструдера и можно печатать.by AlexeyShokarev - Russia RepRap User Group
As far as I know, you need change E_STEPS_PER_MM in motherboard firmware (file configuration.h): 0.706 if use 5mm splined shaft with no gearbox 2,2 for Adrian Geared extruder with standard stepping motor 2,02 for Wades Geared extruder with standard stepping motor In new firmware I see 2 parameters (probably, for 2 extruders): #define E0_STEPS_PER_MM 2.2 // NEMA 17 59/11 geared extruder 8mby AlexeyShokarev - General Mendel Topics
Собрал RepRap Mendel модификацию LaserCut от TechZone только не из фанеры, а из акрила. Получается недорого - комплект деталей из акрила обходится в сумму около 8000 тенге (грубо 1600 рублей), резку акрила делает любая серьезная рекламная студия (у нас расценки 100 тенге/погонный метр (20 рублей) плюс стоимость материала), потом постобработка для которой достаточно обычной электродрели. Для фрезеby AlexeyShokarev - Russia RepRap User Group
А зачем создавать проблему из ничего? Если нужно немного - закажите с ebay (поиск по слову RepRap), ABS там сейчас предлагается, доставка из США не более 2 недель. Если поболее требуется - могу порекомендовать заказать в New Image Plastics (http://www.plasticweldingrod.com/) (минимум 4,4 кг, меньше не отгружают, ABS, HDPE и еще порядка 10-15 видов пластика, любой цвет и форма прутка на заказ, плаby AlexeyShokarev - Russia RepRap User Group