HI, Sorry, some more details Printer Malyan m150. My home settings: #define X_HOME_DIR -1 #define Y_HOME_DIR -1 #define Z_HOME_DIR -1 // Travel limits after homing (units are in mm) #define X_MIN_POS 0 #define Y_MIN_POS 0 #define Z_MIN_POS 0 #define X_MAX_POS 200 #define Y_MAX_POS 200 #define Z_MAX_POS 150 And, here you can see my homeby karcio - Firmware - Marlin
Hi Guys I don't know how to set home point. My command g28 finish in this position ttyUSB3 PC> m114 SENDING:M114 X:64.00 Y:159.00 Z:15.00 E:0.00 Count X: 6018 Y:15013 Z:5929 my configuration.h looks like #define MANUAL_X_HOME_POS 100 #define MANUAL_Y_HOME_POS 100 #define MANUAL_Z_HOME_POS 15by karcio - Firmware - Marlin
Hi guys, using Marlin 1.1.0-RC7 firmware with Z-probe, as all working fine from beginning I notice that points where my probe doing autolevel is not where I want to. I would like to change them. Not sure where should I look in my firmware. I've found this section, my probe checking 9 points not sure if I looking in right part of the code Configuration.h #define AUTO_BED_LEVELING_GRID #by karcio - Firmware - Marlin
Hi Guys, Today I went back to stock E steps (93) and my print looks better, much better. But with 93 steps when I sent command to move extr 100mm my filament move about 65 mm. When I use 150.1 steps and when I send command to move extr 100 - my filament move 100mm Not sure what I suppose to do now. Leave it as it is or find another reason.by karcio - Printing
Hi Guys, Trying to print in PLA xyzCalibration_cube, but as you can see on picture and video I have some problems. I think my Z steps are calibrated correct because if I move z-axis for 100 mm and I check length with caliper it is exactly 100 mm. (maybe not exactly 100mm but close) Printer Malyan M150 For print I use: 0.2 mm infill 30% extrusion 1.1 extruder temp 200 bed temp 60 cooling fanby karcio - Printing
Hi Guys Last couple days fighting with my Z-probe (LJ18A3-8-Z/BX) and 3mm borosilicate glass. Look like those two things does not work together Probe is working on my stock aluminium bed, but I would like to use glass. Printing mostly PLA/TPU. I was trying to put some metal tape between (https://www.woodies.ie/thermawrap-50m-x-50mm-foil-tape-1064013) bed and glass. For now, last try is putby karcio - General
Hi Dust Thank You for clarification - now all clearby karcio - Firmware - Marlin
Hi Trying to set Z_PROBE_OFFSET_FROM_EXTRUDER but every time I change this in code then compile. In LCD > Control > Motion > Z Offset: does not change, FIRMWARE_NAME:Marlin 1.1.0-RC7 Not sure what am I doing wrongby karcio - Firmware - Marlin
HI, Trying to add z-probe to Malyan M150. Using FIRMWARE_NAME:Marlin 1.1.0-RC7 When I change settings about bed levelling and z-probe I can compile without any issues, but when i uncomment: #define SDSUPPORT I can see verification error ... /home/karcio/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino9/bin/avrdude -C/home/karcio/.arduino15/packages/arduino/tools/avrdude/6.3.0-arduino9by karcio - Firmware - Marlin
Hi, finally found how to upload firmware. Just need to do this -Power off printer. -Press center button on panel. -Power up printer, please keep center button pressed. -Release center button. -Look up COM port from windows device manager. Type below command into windows console: avrdude.exe -v -p atmega1284p -c arduino -P com4 -b 57600 -V -U flash:w:marlin.hex -Reboot printer if necessary.by karcio - Firmware - Marlin
I was trying all speeds - still the same Could you please explain how to use avrisp or upload firmware directly? Do I need to use those?by karcio - Firmware - Marlin
Hi So, I've check chip on my mainboard - ATMEGA 1284P AU1524 in Arduino my config looks: Board: Sanguino Processor: ATmega 1284 or ATmega1284P (16Mhz) Compile success, but upload does not Using Port : /dev/ttyUSB0 Using Programmer : arduino Overriding Baud Rate : 115200 avrdude: stk500_recv(): programmer is not responding avrdude: sby karcio - Firmware - Marlin
Ok, small update I was able to compile last merlin firmware with my changes, just one question. For this I have do add mainboard to board manager I had to select my mainboard in configuration.h #define BOARD_MELZI in Arduino I select board as Sanguinom not sure what select as programmer I was trying few and finally I got avrdude: stk500_recv(): programmer is not responding avrdude: stkby karcio - Firmware - Marlin
QuoteRoberts_Clif I use OctoPrint with a raspberry Pi and can send G & M codes to the printer. If you have a way to send these codes you may try to send M503 ; Print current settings This may give you all the values @Roberts_Clif Yes, I have the way to send gcode using Pronterface. Thank you very much for help.by karcio - Firmware - Marlin
QuoteRoberts_Clif Do you know the configuration settings, Or can you read them from your current firmware. Yeah, this is problem, stock firmware came with printer, so I have no any configuration saved. I can't backup I guess I think I can use gcode to read firmware,steps, etc from printer, not sure if I can read anything else from printer. Also not sure if I can check mainboard name from printby karcio - Firmware - Marlin
Hi Guys I have Malyan M150 with stock firmware. So far I was happy with that but I've bought autolevel sensor and for this feature I need new fw. Could you please answer my questions? can I download latest fw from github or should I find dedicated fw for my printer? is it enough to edit just two files Configuration.h and Configuration_adv.h ? can I use latest arduino ide (fedora 28) for compby karcio - Firmware - Marlin
Hi Guys, I'm sure I need to install skeinforge in my Arch, but so far I'm not sure what package I need to install. Using pronterface + slic3r. I was trying find skeinforge_craft.py inmy system but looks like is not there. My default path for this is: slice command: python skeinforge/skeinforge_application/skeinforge_utilities/skeinforge_craft.py $s Slicer options command: python skeinforge/sby karcio - Skeinforge