Show all posts by user

Re: Mechanika - 16 years ago

Az szerintem nincs. Egyedul az STL fajlokat tudod letolteni, amit be tudsz olvasni utana barmilyen CAD szoftverbe. Legalabbis CATIA-ba igen, mert en azt hasznalom. De varj, most jut eszembe, hogy valamelyik orult arc azt jatszotta, hogy STEP-be atkonvertalta az egesz gepet, mindjart utananezek...

by Satuna - Hungary RepRap User Group

Re: Szoftver - 16 years ago

Ok kosz, majd figyelek. Most a hetvegen nem lesz idom, de hetfon nekiallok. Adam

by Satuna - Hungary RepRap User Group

Re: Szoftver - 16 years ago

YES!!! Ez nagyon jo, hogy leirtad, azt hiszem ertem a kepek nelkul is, ahogy lesz ra idom, megcsinalom. (Valszeg csak hetfon.) Nekem pont erre a Subclipse-re lenne szuksegem, mert a fejlesztoi vezriokat emiatt nem tudom kovetni, igy a host-om eleg regi. Hackelni meg nem tudom, mert ahhoz nincs tudasom...

by Satuna - Hungary RepRap User Group

Re: Szoftver - 16 years ago

Laxi, Linuxon vagy XP-n?

by Satuna - Hungary RepRap User Group

Szoftver - 16 years ago

host controller temak

by Satuna - Hungary RepRap User Group

Mechanika - 16 years ago

Mechanikai temak

by Satuna - Hungary RepRap User Group

Re: Anyagok - 16 years ago

Yes, ez jo hir! Amit tudnia kell: 1. bioanyag legyen (szoba johet: Polikaprolaktan - a CAPA egy markanevu polikaprolaktan, amit a Solvay Polymers forgalmazott), politejsav, esetleg ABS) 2. minel alacsonyabb olvadaspontu: Polikaprolaktan (75 fok), Politejsav (160 fok). ez fontos, hogy az extruder hoterhelese minel kisebb legyen. 3. minel kisebb legyen a zsugorodasa. En polikaprolaktant hasznalok,

by Satuna - Hungary RepRap User Group

Re: Valaki? - 16 years ago

Laxi, Zsir, igazad van! Kosz! Hajra Arduino! Kivancsi vagyok ra! Rendelek en is egy Arduinot es akkor kicsit osszhangban leszunk... Adam

by Satuna - Hungary RepRap User Group

Re: Valaki? - 16 years ago

Jo reggelt Laxi, Java tokeletes :-)) Az egesz szoftver java alapu, . En nezegettem mar a felepiteset, de nem ertek hozza, igy nem tudom hackelni. Pedig neha nagyon jol jonne egy-ket dolgot kivenni vagy hozzaadni a vezerleshez. Az egesz tulajdonkeppen egy .jar fajlt tartalmaz es ezen belul vannak a kisebb modulok, de ha letoltod, akkor latni fogod: A 0.8.3. verzio van fent eddig, ha kell ujabb,

by Satuna - Hungary RepRap User Group

Re: Valaki? - 16 years ago

A link hasznos, koszi! Ha talalsz valami anyagot, akkor az nagyon sokat segitene mindenkinek. Szuleim (is) a muanyagiparban dolgoznak es van extruder hozzaferesem, a 3mm atm-ju extruderszerszam mar kesz. Ha lenne anyag egybol le tudnak gyartani a szalat... Smooth-cast arakat nem tudok, mert en csak hasznaltam oket, nem vettem :-)) Itt kint reszben ez a munkam volt. "Kb 30 perc utan mar egy kics

by Satuna - Hungary RepRap User Group

Re: EMC2 Based Repstrap - 16 years ago

Ok, got it now. Do not you think it would be easier to use original electronics to run steppers? Or do you need more then 2A for coils?

by Satuna - EMC2

Re: Valaki? - 16 years ago

Szia Laxi, Ezt a szilikont nem ismerem, Biresin-t mar hasznaltam, de pont G-27-et nem. Amit most hasznalok az valami olasz szilikon (a nevet nem tudom), es ugy nem zsugorodik, ha az ontes utan kozvetlenul nyomas ala helyezem (2-3 bar). Most neztem meg a Sika katalogusban a G-27 ertekeit, de zsugorodast nem ir sajnos mas anyagagra sem... Egyebkent milyen hosszu a beomlod? Van eleg anyagutanpotlas

by Satuna - Hungary RepRap User Group

Re: EMC2 Based Repstrap - 16 years ago

Hi, Good idea, I am interested! It could help a lot for people who are into subtractive prototyping to get into additive prototyping too. BTW, why is there a need to write any implementations if the Arduino is already capable to read g-code? Adam

by Satuna - EMC2

Re: Valaki? - 16 years ago

Laxi, Regelni fent a "Log In" menu alatt tudsz. En is Ian-tol rendeltem cimen. Szerintem maj 26 utan tudsz tole rendelni, csak kicsit most gondolom el van havazva... Rudat is tudsz rendelni, 7 kg az egesz, eleg olcson elpostazza neked Ian. PUR-t szilikonba ontod? Ha igen, milyen szilikonba? Complete mechanical Kit-hez elvileg van egy PDF leiras, hogy mi van benne. Opsz, most neztem meg az o

by Satuna - Hungary RepRap User Group

Re: Valaki? - 16 years ago

Szia Laxi, Semmi gond, a lenyeg, hogy halad :-)) Eddig ugy tunik, hogy ketten vagyunk magyarok, akik ilyenben gondolkoznak, de remelhetoleg majd bovul a kor a kozeljovoben. En kb. fel eve kezdtem el epiteni a gepemet es kb. 2 honapja fejeztem be. Azota tesztelgetem, javitgatom, probalgatom. Akkoriban a PIC alapu elektronika volt a "meno", en is ezt epitetem, az Arduinohoz egy-ket honapja keszu

by Satuna - Hungary RepRap User Group

Re: Repraping on XP and Ubuntu - 16 years ago

Bruce, Software worked finally, I made a mistake not copying it into the proper directory :-(( Anyway, v0.8.3. does not support short speed, I suppose. Please, correct me if I am wrong. I have just controlled the jar file and yours is different, contains short speed and nozzle wipe too. Now, printing goes well finally... Huh... Thanks for the host update! BTW why is it not uploaded onto sourc

by Satuna - RepRap Host

Re: Which Software for Arduino electronics - 16 years ago

Ian, Any photos or drawings of what is happening on your tray? Adam

by Satuna - RepRap Host

Re: Valaki? - 16 years ago

Szia Laxi, RepRap-ot akarsz egybol epiteni vagy RepStrap-et? Melyik elektronikat valasztottad? Udv. Adam

by Satuna - Hungary RepRap User Group

Setting curve speed - 16 years ago

Hi, I am having difficulties with setting the appropriate curve speed. Tweaking manual says: Set the preference: Extruder0_ShortSpeed (0.8). Well, I do not find this in the preference list. Neither on Linux neither on XP. Angle speed length and factor are set properly but curve speed is still very low and material dump up. Could anyone tell me where I find this parameter for curve speed? Than

by Satuna - RepRap Host

Re: Software Issues - 16 years ago

I am 1.2 mm away from my tray at the moment. I am not an expert but I would say 7 mm is a lot. My experience is that the closer I am the more preciese results I get dimensianally. Mind, not to get too close otherwise you mess up your deposited filament. I do not know what others use, 1.2 works well on my setup... Adam

by Satuna - RepRap Host

Re: Repraping on XP and Ubuntu - 16 years ago

Bruce, I think Adrian spotted my issue: he asked about the values for the following parameters: -Extruder0_ShortLength(mm) -Extruder0_ShortSpeed(0..1) In the version of 0.8.3. I do not have these parameters. Instead of these I have the following two preferences: - Extruder0_AngleSpeedFactor which is 0.5 - and Extruder0_AngleSpeedLength which is -1 in my case Was there a name upgrade in the so

by Satuna - RepRap Host

Re: Repraping on XP and Ubuntu - 16 years ago

Bruce, Thanks for the update! I tried but does the same thing. I really do not understand this issue... It is certanly not the PIC or some electronic stuff. I am sure its related to software but can not figure out the reason... Adam

by Satuna - RepRap Host

Valaki? - 16 years ago

Van valaki magyarorszagrol, aki RepRap epitesevel foglalkozik vagy gondolkodik ilyesmiben? Udv. Adam

by Satuna - Hungary RepRap User Group

Re: Repraping on XP and Ubuntu - 16 years ago

Bruce, I am using 0.8.3 file release at the moment on XP. As I see on sourceforge this is the latest version, isnt it?? Regards, Adam

by Satuna - RepRap Host

Re: Repraping on XP and Ubuntu - 16 years ago

Hi, Here is a photo of what I was talking about. It is difficult to see as the part is actually functional but the hole on the right hand side is the result of this infilling speed up. So what actually happens is that the machine starts infilling on the left hand side and goes along below the inner groove. Then when it starts coming backwards on the upper side it speeds up. (up to 100% percen

by Satuna - RepRap Host

Re: Repraping on XP and Ubuntu - 16 years ago

"way better" means for me that axis control is more precise. at curves it makes less mess but do not know the reason for this. XP stops before every curve for a little while which is enough to dump up the material. Maybe my XP is full of stuff... dont know...

by Satuna - RepRap Host

Re: Anyone in Italy ??? - 16 years ago

Actarus, I do not know, i ordered filament from bitsfrombites. See: www.reprap.org for contact. Shipping cost a little but its 2kgs which should last for a while. Adam

by Satuna - Discussioni generali - NO PROBLEMI DELLA STAMPANTE

Repraping on XP and Ubuntu - 16 years ago

I have been suffering with getting the infilling pattern right in the last few days when I experienced an interesting thing. Finally, I optimized the process and outlining and infilling is okay now with the widebar.stl. Then I thought to try a few RepRap parts of which PCB clamp came off the tray well (now part of my machine, Yes!) but I had an intersting error during the Z studding tie and polyh

by Satuna - RepRap Host

Re: Annyoing extruder controller problem - 16 years ago

Sure, I will put them on the builders blog when I get a little free time. I am still at the testing phase and want to make the widebar and 10mm cube perfect then go on. BTW if I am here... Last night I came across some strange thing: the sync between x and y axis worked sometimes and sometimes not. Thus infilling was really strange (infilling lines not paralell). I checked the PICs and Y showed

by Satuna - Controllers

Re: Supplier for parts - 16 years ago

Hi Erik, It depends on how many kits you need. Unfortunately, one kit costs a lot as all RP machines cost a lot :-)) If a group of people are interested (at least five) we can create silicone molds and inject the parts. Now, I'd better write to Ian Adkins as he is doing the same thing and I really do not want to mess up anything. If our service is necessary besides Ian's I will get back with an

by Satuna - For Sale