thank you it works perfectly !by Nikki81 - General
What is the best free kinect 3d scanning software for windows or Linux ? I've had a look around the internet but everything I have found needs a 64 bit system . Thanks Nikkiby Nikki81 - General
Where can i buy the mks sbase board using PayPal ?by Nikki81 - General
Where can I get fiberglass sleeving for my hot end thermistor? Thanks Nikkiby Nikki81 - General
Just been looking to get some steppers and was wondering what was the best brand for quality and reliability? Thanks Nikkiby Nikki81 - General
Thank You ive just ordered some IRLB3034pbfby Nikki81 - RAMPS Electronics
I did a bit of testing last night and found that 1 Methylene Chloride is horrible nasty stuff and 2 it had only taken a few minutes to clean them up and they just needed a rinse and a wipe.by Nikki81 - General
What is the best mosfet to use to replace the stock one on a ramps 1.4 I have had a good look round the net and found people saying different parts number but ive gone and just confused myself. which one will give me the best performance and reliability ? thanks Nikkiby Nikki81 - RAMPS Electronics
How long should a soak my nozzles for I've had them in for a few hours now and I am not sure it's working.by Nikki81 - General
I am interested to see what the solution is to this as i have the same problem. I have tried slowing down the homing speed changed the stepper driver and tweaked the pot but with no real results. I did think that the threaded rods might be to blame but after checking they seem fine. thanks Nikkiby Nikki81 - General
Thanks I was just on my way to get my taps out to run a m5 tap down it but I'll try the clip first !by Nikki81 - General
I've fitted it right when I stripped it down it was still tight it seems that even that it's tight its slipping past I've ordered some dichloromethane to clean my nozzles am going to drop e3d a email and see what they say. Thanks Nikkiby Nikki81 - General
Ive just run the extruder stepper for a hour i think its over heating and missing steps would this make the problem ive got ?by Nikki81 - General
No I've tested it and it's holding tight. I just been thinking that the filament might be to blame but not sure howby Nikki81 - General
My e3d lite6 has started to push its ptfe liner out then block up. I put a new liner in it yesterday and a new nozzle it was all put together correctly and was all nice and tight after warming it up to 245c I started a print kept I eye on it for 30 mins when I came back it had done the same thing. Am not sure what to try next Thanks Nikkiby Nikki81 - General
will a inductive sensor work through a glass bed if I put a thin aluminium sheet under the glass ? thanks Nikkiby Nikki81 - Reprappers
I've been given a jy-mcu module that needs resetting I can see it on my Bluetooth list but am not able to connect to it via serial adapter. Thanks Nikkiby Nikki81 - General
I am having problems with my z axis am loosing or gaining 0.16 every time I home it from one side of the axis to the otherby Nikki81 - General
Are optical endstops more accurate than micro switches ? Thanks Nikkiby Nikki81 - General
I would like to to build a new bigger printer which reprap has the biggest build area and most solid construction ? Thanks Nikkiby Nikki81 - Reprappers
where is the best place in the uk to get pei sheet ? I am having a hard time finding anywhere. thanks Nikkiby Nikki81 - General
Thank You there are r100 ill get tweaking ! thanks Nikkiby Nikki81 - General
Thanks looking at one of my spare driver boards the r1 says 303 ? Thanks Nikkiby Nikki81 - General
How do I calculate the correct voltage for my stepper drivers ? I have had a look at the wiki but I don't understand(I am not good with numbers) is it amps x inductance = voltage ? Thanks Nikkiby Nikki81 - General
I have found the problem the front of the printer has bent slightly so I have come up with this as a ruff idea that will alow front to back and side to side adjustment of the 608 bearing and will reinforce the front of the printer. It is times like this I wish I was better at using the design software. I have attached the ruff design. thanks Nikkiby Nikki81 - Reprappers
I have been using my p3steel with no problems for the past 2 weeks but know I am unable to keep the belt on the y axis idler. I have reinforced the stepper mount to stop the flexing realigned the belt in the carriage mounts but it keeps pulling of to one side. Is there any way to make it self aligning? Thanks Nikkiby Nikki81 - Reprappers
I think I have found the perfect setting I have been testing 0.25 with the 0.5 test cube.by Nikki81 - General
Thank You I will run some test prints tomorrow. I have been using 0.2 layer hight and have been getting very good prints but it is very slow it took over 5 hours to print just the body of a wades extruder but not having any experience am not 100% sure if that is just how long it takes. Thanks Nikkiby Nikki81 - General
what is the best layer hight for a 0.4 nozzle so there is a good balance of quality and speed ? thanks Nikkiby Nikki81 - General
I have had a play this morning and found that it was set to 3000 mm s ! I've dropped it down to 30 and it seems to be working.by Nikki81 - Printing