Show all posts by user
Here's what I made, here's a photo, and here's a link to the [[page]] on RepRaps wiki!
Re: ABL is not even worth it anymore 
- 9 years ago
Just to make sure, are you using the standard: G28 X0 Y0 G29 for starting g-code?by isonoob - General
Re: Folger Prusa i3 Kit from ebay - 9 years ago
Everyone starts off printing pretty much lumps of poop at some point. Just have to dial in the settings! Wish I took pictures of my failed prints, they were pretty bad, be ready to have a whole bunch of failed prints, lumps of poop, balls of stringy filament etc. Stay with it, keep fine tuning and eventually you'll get great prints!by isonoob - Prusa i3 and variants
Re: Folger Prusa i3 Kit from ebay - 9 years ago
if your bed can only get to around 90 degrees celcius comfortably, that's good enough to get an ABS print sticking with additional bed adhesives. I find little difference between 90 to 100 tbh. If you're having trouble getting a part to stick, try putting down blue painters tape on the bed and rubbing a glue stick on the top of the blue tape, dont need much glue.by isonoob - Prusa i3 and variants
Re: Folger Prusa i3 Kit from ebay - 9 years ago
Gannicus, If your nozzle is not going down, your z limit switch may not be configured properly, i havent read the whole thread, so I'm not sure what state your printer is in, but if you move the Z-Axis up manually 10mm and then tell it to home and it doesnt move, your Z endstop may be giving out a "TRIGGERED" command. Send in an M119 command to check the status of your endstops. They should allby isonoob - Prusa i3 and variants
Re: Folger Prusa i3 Kit from ebay - 9 years ago
QuoteGannicus Thanks guys...I've calmed myself...and will really crack down on this this weekend to get it running once and for all. I just wish there was some way to really pick your brains. A web forum takes too long to get replies etc. LOL I know the issue now is that I don't know how to use the software. I know that. It's all software issues at this point. I don't get why all four of those pby isonoob - Prusa i3 and variants
Re: PLA to be made from poo. - 9 years ago
Quotedave3d Explains why my prints are often crap. XDby isonoob - General
Re: autobed leveling using a fsr (force sensing resistor) - 9 years ago
If this is to actuate on the bed, it wouldn't work since you don't want anything to be at a lower point than the nozzleby isonoob - General
Re: PLA to be made from poo. - 9 years ago
Ive always wondered, how can we make printing PLA smell as bad as ABSby isonoob - General
Re: Error: no checksum with line number, last line 41 - 9 years ago
what software are you using? I know with repetier, ive seen some firmware versions require a line number preprended to a command and a checksum appended to the end. Try using repetier host to interface with it, see if you have any luck. Also check your hot end for damage, 700c is pretty high, if it really got there, probably did some damageby isonoob - General
Re: New here! Looking for feedback on a printer I'm considering purchasing - 9 years ago
Not sure why disruptivetech is being so hostile... I always try to find stuff that ships within my country if that helps. try looking around for us based companies (for some reason in my head I made the assumption you're based in the US) such as Makerworks, makergear, makerfarm, can't remember them all off the top of my head, but htere are a ton out there, maybe some others can chime in. bestby isonoob - General
Re: Cheap Filament.... The bottom fell out the market? - 9 years ago
It doesn't necessarily render hot ends useless, but rather clog a hot end which can be a pain to unclog. Ive had clogs a couple times with poor filament myself, but nothing that wasn't fixableby isonoob - General
Re: Cheap Filament.... The bottom fell out the market? - 9 years ago
it's not a myth...by isonoob - General
Re: Leveled Bed >> Auto-Leveling Probe - 9 years ago
doh! guess my views on bed leveling probe aren't so popular! probably why the shift towards manufacturers including them is happnening... Maybe ill dust off the ole induction probe and give it another chanceby isonoob - General
Re: Cheap Filament.... The bottom fell out the market? - 9 years ago
I grabbed a ton of rolls from microcenter, they often sell the toner plastics randomly for 14.99 without advertising it on their website. Not getting any issues so far with it (knock on wood). IMO the quality stuff is UltiMachine plastic, have always been a huge fan, but you just cant beat the price of the microcenter filament.by isonoob - General
Leveled Bed >> Auto-Leveling Probe - 9 years ago
Anyone else agree? Recent put together a PrintrBot Simple Maker Edition kit that didn't come with a bed leveling probe, then purchased the upgrade kit for it and put a bed leveling probe in. Few days later, ditched the probe. Nothing beats a leveled bed thoughts? Is this a universal opinion or am is the inverse popularly agreed upon? I see a bunch of printers coming out now with bed leveling proby isonoob - General
Re: Poor print Quality - 9 years ago
are your z steps in the firmware calibrated properlyby isonoob - Printing
Re: Newbie overwhelmed by software choices, which one to choose? - 9 years ago
I started out using Slic3r and Pronterface combo, was not a bad way to go imoby isonoob - General
Re: Duet and Simplify3D - 9 years ago
what firmware does the duet run? If it's standard Marlin or Repetier, it'll workby isonoob - Controllers
Re: CAUTION! Simplify3D / Reprappro Melzi Users -FIXED - 9 years ago
the settings found in the g-code tab for origin and origin offset override those settings found in tools - options - machine, IF the Update Machine Settings checkbox is checked. I usually keep the checkbox checked and use the correct settings in the g-code tab. This means you should have your build volume 200x200x200 and then origin offset 100x100x0. this will do what u want also i have found soby isonoob - General
Re: Need help setting up Pronterface in Ubuntu - 9 years ago
Just a question, why are you using linux if you don't have no experience with it? You could also try running Repetier Host, it may work for you. You will have to run it's dependency and configure scripts first.by isonoob - General
Re: Computer stolen, Printrun doesn't work on new one. Help would be appreciated. - 9 years ago
ahhhh I read it incorrectly, my bad!by isonoob - General
Re: Sourcing Reprap parts in BULK for Uni club project
- 9 years ago
QuoteSam Groll Robotdigg looks like a great site, I will certainly look through there when I compare sources. thanks gmh39. We are going to make Prusa i3s however I think some students are making some different innovative designs (ie a box 3D printer) Pm recieved and sent PTB ggherbaz, that is what I hope many students will do more after they build this to get started (it is a cheap entry leveby isonoob - General
Re: Computer stolen, Printrun doesn't work on new one. Help would be appreciated. - 9 years ago
What type of printer/electronics board are you running? Do you see the correct COM port in the ports section of pronterface? Have you installed the proper drivers for your board?by isonoob - General
Re: CAUTION! Simplify3D / Reprappro Melzi Users -FIXED - 9 years ago
can u take a screenshot of pronterface on connection? When you ocnnect with protnerface, the printer should spit out some communication to pronterface which u can seeby isonoob - General
Re: CAUTION! Simplify3D / Reprappro Melzi Users -FIXED - 9 years ago
AJet, just to clarify, are you able to connect and control the printer via pronterface/repetier host?by isonoob - General
Re: CAUTION! Simplify3D / Reprappro Melzi Users -FIXED - 9 years ago
QuoteAJET69 hi donandi, were you able to resolve your connection issue with Simplify3d? I have the exact same issue and can't find a solution for it. I have a Mendel90, running Marlin 1.0.0 RC2 Simplify3D suggested I install Teensyduino 1.20 for a better USB support via Arduino (I 'm using 1.0.6). So I have installed Teenyduino in my Arduino, recompiled and uploaded Marlin, power cycled the prby isonoob - General
Re: Why is the E3D hotend so popular? - 9 years ago
i wouldn't say it's superior, it's a good hot end though.by isonoob - General
Re: portabee3dprinter.com/ - 9 years ago
just an update, received my printer today! Made some minor hardware adjustments and got it printing.by isonoob - General
Re: portabee3dprinter.com/ - 9 years ago
Quoteportabee Hello All, So! Sincere apologies, we have been very busy with email, and quite a bit late on our current batch of shipments. Everything is going smoothly, and we will ship out these machines in the coming weeks. Apologies for the long delays! We have been engineering on the fly, and this has lead to some manufacturing delays. Ok, Thanks and we look forward to delivering yourby isonoob - General
Re: Part tolerances - 9 years ago
Im a big fan of Simplify3D, love the features and interface. I've used kisslicer, cura, and slic3r, got the best results using s3d personally. imo, worth the $140by isonoob - Printing