On the video , we can just hear the fan increase /decrease and th led that is changing a little. Is there a way to use fan1 instead of fan0 for my layer fan? With Marlin/repetier firmware , i know how to change pin assignation but with reprapfirmware...by Cammi - Duet
i have try smaller increment with S . I can see the light brightness changing. I have made a small video where i'm changing the speed of the fan0 : M106 state after M106 S0 in attachement.by Cammi - Duet
Yes i confirm for the firmware and the config file. Very strange problem. Is it possible that this pins are defect? I don't think so because I can increase and decrease the speed.by Cammi - Duet
Yes i can comfirn that i have only a 2 wire fan on Fan0. When i power on the board , the led near the fan0 pins is On and the fan start spining. I'm at work for now. Will do more test tomorow.by Cammi - Duet
I have done all my test with a simple 2 wire 40 mm fan.by Cammi - Duet
Another strange thing that i've see with all the try i've done : Firmware 1.09 k and m : I can control fan0: increase and decrease the speed but can't stop it. Everything ok on Fan1 Latest firmware 1.09 r :I can control fan0 , increase and decrease the speed but can't stop it . Fan1 did not respond...by Cammi - Duet
I will try s0.1, s0.2 s0.3. I said that i've try my fan my on the fan1 connector and everything was working fine. i've only got the problem on the fan0 connector EDIT : just tried the M106 S0.1 S0.2 ,etc... with this command, i can change the fan speed as i do with M106 S0-255. Result is the same , I can't stop the fan.by Cammi - Duet
thx for the reply but... Nothing change when i remove the lines... i can not stop the fan but i can change the speed. I try different firmware on my delta printer (DC42) and i have always the same problemby Cammi - Duet
Hello , I have a DUET 0.8.5 and i have a problem with my layer fan 0 , i can't stop them... I can change the PWM of the fan 0 but when i ask him to stop : M106 S0 , the led on the DUET stay On and the fan don't stop. I've try to put the fan on the fan1 output and everything is just working fine.. i can start and stop the fan with M106 P1 S0-255 and i can see the led on the DUEt going on or oby Cammi - Duet
David J , change your Z height in the config file. it might too high that why your nozzle is dragging on the bed when probing.by Cammi - Delta Machines
hello DC42 , When the autocalibration is performed , is there a way to save the data or do we have to redo the calibration everytime we start the printer?by Cammi - Delta Machines
Petit test de torture pour le retract sur la AIO : Reste quelques petits fils facon spiderman mais c'est pas mal!by Cammi - RepRap Groupe d'Utilisateurs Francophone
Juste pour faire un petit retour sur la AIO : La qualité est au top , ca se monte nickel. Biensur comme je fais pas comme tout le monde et que j'utilise repetier firmware, j'ai du bidouiller une table de thermistance qui va bien mais tout est expliqué dans la notice, c'est juste fastidieux à faire. Seul point négatif pour ma part, le ventilo de 25*25 qui fais un sale bruit mais ca je m'en doutaby Cammi - RepRap Groupe d'Utilisateurs Francophone
Ok t'a une E3d que t'as fabriqué toi même et tu juge la e3d originale d'après les plans que tu as repris? y'a un soucis au niveau de l'usinage du heatbreak chez e3d ou leur sous traitant. Ca a été démontré point barre. Le fait que le heatbreak que TU as fabriqué fonctionne ne prouve en rien que ceux de chez E3d soient bons. Faudrait voir a pas tout mélanger.by Cammi - RepRap Groupe d'Utilisateurs Francophone
La hotend de chez 3dlabtek avais toujours bien fonctionner chez moi . Ca me fait plus penser a un probleme de chauffe trop importante que le ventilo de hotend n'arrive pas a canaliserby Cammi - RepRap Groupe d'Utilisateurs Francophone
Salut, Dans repetier-host : -Réglage imprimante /imprimante , regarde si la case "Vérifier température du Plateau et de l'extrudeur" est cochée .by Cammi - RepRap Groupe d'Utilisateurs Francophone
Le petit "plus" ca serait de filer un lien pour acheter le même ventilo radial :pby Cammi - FoldaRap
Hello , Voilà un petit lien que je trouve pas mal pour les printeuse de type Delta :by Cammi - RepRap Groupe d'Utilisateurs Francophone
Comme quelqu'un te l'a souligne plus haut tes endstops sont réglage avec le petit potard qu'il y'a dessus. Et comme je l'ai marqué plus haut , meme si ton Z0 est ok en X0 Y0 , si tu touche au delta radius ou au endstop , tu devra changer la valeur de Z a nouveau . la calibration d'une delta est un cycle à répéter. 1 : Dégrossir le delta radius (plus important) 2 : Réglage hauteur du Z pour etrby Cammi - RepRap Groupe d'Utilisateurs Francophone
Hello Ton soucis est le plus courant lorsque l'on regle une delta pour que la tête se déplace en // avec le bed . En fait c'est la partie la plus longue a effectuer et elle consiste a jouer avec la valeur "DELTA RADIUS" , dans Marlin :#define DELTA_RADIUS (DELTA_SMOOTH_ROD_OFFSET-DELTA_EFFECTOR_OFFSET-DELTA_CARRIAGE_OFFSET). Tu vois donc que le delta radius se base sur un calcul , toi tu va deby Cammi - RepRap Groupe d'Utilisateurs Francophone
un message dans les logs de repetier (ou ponterface)?by Cammi - RepRap Groupe d'Utilisateurs Francophone
hello Andy, Realy love your job on this printer! I'm currently working on making one but i'm not gonna use magnetic arm , i have some traxxas Rod end and some carbon tube to make my arm. My problem is that i'm not really good for designing a part and i wanted to know if there is a chance to see a version of your effector with traxxas ball joint fixation like the kossel mini effector (same spaceby Cammi - Delta Machines
elle a quoi "d'ouverte"?by Cammi - RepRap Groupe d'Utilisateurs Francophone
Correspondance entre les valeurs de la photo et tes valeurs : Diagonal ROD :345=>213 Smooth rod offset: 225 =>149.64 Effector offset:35=>19.89 Carriage offset:17=>19.5by Cammi - RepRap Groupe d'Utilisateurs Francophone
Salut , tu clique sur download zip a droite . Ensuite tu dezip le dossier et tu rentre dans le dossier Marlin-Marlin_v1 , puis dans marlin /example_configurations/delta. De là tu copie les deux fichier qui s'y trouve (configution.h et configuration_adv.h). Tu reviens en arrière dans le dossier Marlin-marlin_v1/marlin et tu colle les deux fichier, tu confirme pour remplacer les fichier et te voby Cammi - RepRap Groupe d'Utilisateurs Francophone
Dans marlin il y'a une sécurité pour éviter d'extruder du fil à froid et de créer des contraintes très forte sur la hotend/extrudeur. 2 solutions donc pour tester le moteur de l'extrudeur : -faire chauffer la hotend à au moins 170° (je crois bien que la sécu se trouve à cette température. -envoyer la commande M302 qui désactive la sécurité=>> !!! ne pas mettre de filament pour extruder àby Cammi - RepRap Groupe d'Utilisateurs Francophone
Simple perte de connexion entre le pc et la printeuse donc oui la printeuse attend des infos du pc qui se sont perdus entre le ports USB et la carte. plusieurs pistes donc : - Le câble USB ( trop long, mauvaise qualité,etc..) - Port USB faiblard ( tester sur d'autres ports) Pour valider que cela proviens de la connexion, le must est de faire un test de print depuis un LCD et/ou d'une carte SD.by Cammi - RepRap Groupe d'Utilisateurs Francophone
Selon le diamètre de ta duse , il peut être nécessaire d'augmenter le nombre de top layer lors de l'impression, car là sur la photo on dirais que le filament "tombe" dans l'infil. A tester donc.by Cammi - RepRap Groupe d'Utilisateurs Francophone