Show all posts by user
Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"
Re: FLSUN from AliExpres - 9 years ago
I'll double check them again....thanks.by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Ahh great. I followed your guide. The setup was pretty easy. One last issue. I think I have a setting wrong somewhere. After the auto cal is completed i saved the settings. I then brought the Z to 0 and I noticed that its way above the bed. My measured Z Height is 277.7 mm which is entered into the firmware. My Custom Probe Z height is 2.8 mm After I loaded it and performed the M502 and M500 Iby cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Thanks, I'll give it a shot. BTW what the consequence if the values are off? Also I noticed a Z-Offset in the config file. What's that for? is that for the nozzle to the auto-bed level switch trigger?by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Thanks for the extra time putting in. The problem is that I've changed the Kossel by getting a different effector and will be changing the carriage to a slide soon. So the number for you might not work for me. I've figured out how to measure the two (Rod length and Carriage offset) just trying to figure out the effector. Using the same rod for measuring the length and carriage offset, I'm assumby cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Not a clue what that means. Need a video or something....by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Is the measurement of the Effecvtor Offset from the Bolt on the rod to the center of the nozzle?by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Any chance of a picture of your machine? I'm not sure but it might be different from mine. The carriage offset and effector offset values in your AC is different then mine.by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
I currently have a question. After calibrating it. I noticed that the -X axis from min to the +X max it slants upwards. But when I check my X,Y,Z height, they seem fine. What could be causing this? Could it be mechanical?by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Interesting. From 1.6.6 to 1.6.8 it works. Cool. Oh BTW, when mine stalled, I realize it wasn't anything to do with the USB is had everything to do with the stupid cheap power port. It seems that the green connector that they used is only rated for 10A and I'm using a heated bed along with motors it melted the side and caused power issues. I solder directly to the PCB going to run another test.by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Well I downloaded the firmware and tried to compile it in 1.6.6 and I get the following erros: Arduino: 1.6.6 (Windows 10), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" sketch\Marlin_main.cpp:1726:32: warning: extra tokens at end of #ifdef directive #ifdef ENABLE_AUTO_CALIBRATION && DELTA ^ sketch\Marlin_main.cpp:2422:36: warninby cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Is it possible to get a copy of that firmware? Mines gives int convert to char errors..... Thanksby cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
I know I'm using simplif3d and I had to up my buffer to get it to work. How your version of the Marlin firmware? Does it give you warning when you compile it?by cotang - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Have you tried increasing the buffer? There should be a USB buffer depending on the slicer/host program you are using that might fix it. Also the Marlin version I got gives me errors when I compile it. Something to do with converting int to char or something.....by cotang - Delta Machines