Show all posts by user
Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"
Re: FLSUN from AliExpres - 9 years ago
QuoteLVD The springs have arrived and after installing them on the rods it really makes a difference. 1.5€ well invested I'm printing some clips now to hold them in place. I'm just using simple rubber elastic bands with a paper clip holding them together. I know this is an el'cheapo way to do it, but my results are great without spending a dime.by junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Quotedeltamelter Quotejunkyjunky QuoteLVD You need to connect the heat-bed power leads (black and red) to the green connector 'heated bed hot line', and the power supply needs to be connected at power + and power - That did it! Thank-you again!! Ok, now only a few more non-technical questions: 1. I put my glass plate over top of my aluminum heat bed, but which side do you guys have facing up?by junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
QuoteLVD You need to connect the heat-bed power leads (black and red) to the green connector 'heated bed hot line', and the power supply needs to be connected at power + and power - That did it! Thank-you again!! Ok, now only a few more non-technical questions: 1. I put my glass plate over top of my aluminum heat bed, but which side do you guys have facing up? The smooth side or the brushed siby junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
QuoteLVD What motherboard? Which connector did you use? Sorry, I noticed I didn't include that in my initial response. I edited it with a picture of the motherboard and circled the spot i connected it in green. I used the two pin connector (white cable) to connect to this port. The other two wires (black and red) were obviously power leads and go to my power supply (same as the one in my postby junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
QuoteLVD The sensor does not have a polarity; and since you have a temp reading it is working. What board do you have and where did you connect your heat-bed onto? MK3 12V Aluminum heat bed, same as this one: I have it connected in the spot I circled in green (see attached picture), same place the instructions say to connect.by junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Unfortunately not... Still trying to work that out. Does the white two-wire sensor have a polarity to it? The only thing I can think of is that I need to flip that connection on the motherboard. I only modified the code to change the value of TEMP_SENSOR_BED from 0 to 1. I left everything else unchanged.by junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
QuoteLVD Here’s the latest version of the FLSun firmware: G29 now takes some parameters to overrule the default settings in configuration.h: G29 P(number of grid Points, min 3 max 10) B(bed probable radius) G33 now probes multiple points as well (upto 12*3 + 6 centre points): use A to run autocalibration, without A is just checks if the calibration is OK. Beware in order to speed up things theby junkyjunky - Delta Machines
Re: FLSUN from AliExpres - 9 years ago
Hi All - like many of you I bought my printer on AliExpress and it has been really fun getting this thing put together. I'm sort of in the last throws of finalizing my build, but I have two issues: 1. I cannot seem to get the curvature adjustment done. No matter what I adjust the DELTA_SMOOTH_ROD_OFFSET code to nothing changes. I'm left with the extremes about 1mm higher than the centre of thby junkyjunky - Delta Machines