Nou ik blijf lekker tegen mezelf praten. Het is in ieder geval opgelost. Ik had het firmware type op Relative E staan ipv Absolute E. Inmiddels heb ik dus wel de eerste prints gemaakt.by Vinculum - Dutch User Group - Archive
Nou we zijn weer wat verder. Ik zit nu een beetje te klooien met de extruder. Als ik handmatig het commando geef om 10mm te extruden dan duwt hij inderdaad 10mm richting de hot end. Laat ik nu een testkubusje printen dan lijkt het alsof er meer ge-retract word dan ge-extrude (wat een mooi nederlands weer), Geen idee wat er nu fout gaat. Hier mijn settings binnen KISSlicer: g_code_matl=3B204D617by Vinculum - Dutch User Group - Archive
En het is ook zo! Als een delta in spiegelbeeld print dan moeten de 2 voorste motoren omgewisseld worden. En vergeet ook niet de endstops te verwisselen... Hij print nu weer de goede kant op.by Vinculum - Dutch User Group - Archive
Mijn gevoel zegt, x motor op de y aansluiting en andersom. Plugorientatie hetzelfde. Dat betekend dat bij een G28 ze toch de goede kant op gaan alleen tekenen ze niet van links naar rechts maar van rechts naar links. Volgens mij is dat nu juist spiegelen.... Ik ga het gewoon proberen. Kan hooguit kapot gaan.by Vinculum - Dutch User Group - Archive
Ja zou kunnen. Ik ga het proberen. Het is via de firmware iig niet te fixen. Als ik de X en Y as inverteer dan gaat het heel erg fout. I know, i've tried... Ik gebruik KISSlicer en die heeft het in ieder geval niet. Wat ik me afvraag, moet ik stekkers 180 graden draaien of moet ik de beide motoren met elkaar verwisselen? Of beide?by Vinculum - Dutch User Group - Archive
2-2,5 uur. Reistijd is bijna langer dan het programma. Ach ja, volgende keer...by Vinculum - Dutch User Group - Archive
Waarom nou weer helemaal in Zwollywood? Zucht...by Vinculum - Dutch User Group - Archive
Nou, na veel gepiel ben ik een heel stuk verder. Geen idee wat er is gebeurd maar ineens heeft het aanpassen van de radius effect. Dus na een avond tot laat klooien is dit het resultaat: De afwijking is max 0,04mm. Door de speling op de Traxxas joints is er tijdens het bewegen nog wat speling maar dat is inmiddels opgelost zoals je ziet op onderstaande filmpje. En vandaag maar eens een testjeby Vinculum - Dutch User Group - Archive
Ok i've tried a lot of different things including completely replacing the firmware with the Repetier firmware and host. Unfortunalty that caused more problems so i'll leave that for now. Since i seem to be the only one having this issue i'll post my config file here. Maybe i have some conflicting settings or something. Could someone please have a look at it because i'm really stuck and baffled tby Vinculum - Delta Machines
Geil zou ook niet het woord zijn geweest wat ik zou gebruiken. Persoonlijk vind ik de Delta's zoals de Kossel Mini en de Cerberus nog altijd veel mooier. Kijken we naar commerciele producten dan vind ik de Buccaneer erg mooi en de Form-1. Anyway, on topic. Op het delta deel van dit forum krijg ik 0 respons wat weer erg motiverend werkt... Op het seemecnc forum daarentegen krijg ik wel (zinnigeby Vinculum - Dutch User Group - Archive
The buildvolume for all options is about the same. But why ditch the Kossel/Rostock? I'm building the Rostock Mini but it can easily be scaled to as big as you want. Some have made it 150cm tall. Even the XY size kan be adjusted. You just need to alter some parameters in the firmware. The mechanics stay the same. I think there even is a OpenSCAD file which calculates all the required measurementsby Vinculum - Delta Machines
Had ik al gedaan.... Ik zal het zeker laten weten. Mijn plan was eerst ook om een mendel te maken maar ik vind ze er zo rommelig uitzien. De Prusa i3 was toen nog maar bar weinig over bekend behalve wat er op reprap.org staat. Een delta leek me makkelijker qua opbouw en vooral veel gaver! Ik beschouw mezelf maar als een soort Delta pionier in NL. Ik loop nu al met ideeen rond om een Kossel Miniby Vinculum - Dutch User Group - Archive
Anybody? I'm stuck now and cannot continue.by Vinculum - Delta Machines
I've run into a little snag. I'm trying to level the bed. Beneath the towers it's set correctly with the setscrews. I can just move a piece of paper between the nozzle and the bed but i feel it dragging a bit. So this is as it should be. If i drop to Z0 in the center i slam into the bed. After carefully trying i found it is a bump of 0.9mm. The solution according to should be to decrease the DELby Vinculum - Delta Machines
Dank! Ok, nu heb ik toch wel een raar iets. Ik ben nu dus bezig om het bed mooi geleveled te krijgen. Het plateau is een 5mm dikke borosilicaat glasplaat van 17x17cm. De torens zelf heb ik allemaal mooi goed gekregen door de aanpassing van de stelschroeven. recht onder alle 3 de torens kan ik net een papiertje bewegen maar ik voel dat hij er dicht tegen aan zit. Dat zou dus goed moeten zijn. Hetby Vinculum - Dutch User Group - Archive
Ik heb nog een vraag over de Marlin firmware. De steps/unit snap ik. De acceleration (hoe snel mag ik naar een coördinaat toe) snap ik ook. Maar wat is de feedrate en wat zou de waarde moeten zijn?by Vinculum - Dutch User Group - Archive
Er is er weer een 3D print verslaafde bij in NL! Ditmaal vanuit de buurt van Gorinchem. Na jaren actief te zijn in de high end zelfbouwaudio (speakers, versterkers, DAC, platenspeler, etc) ben ik nu 'overgestapt' op 3D printen. Vanaf moment 1 heeft het me al gefascineerd (zat zelfs in de beta van Shapeways) maar vooral door geld en dus andere hobbies weinig mee gedaan. Nu is de audio set klaar, dby Vinculum - Dutch User Group - Archive
Thanx guys! That worked. I did not know about that feature. I actually have it correctly going to the bed now. Still need to calibrate the flatness of the surface of course but were making progress. Did a quicky with a pen and the standard 20mm cube test and it measured really well. Can't wait to make my first print. But i need to fix my extruder first but that's a different topic.by Vinculum - Delta Machines
Thanx for youre reply! I've changed it in the Arduino IDE and them uploaded it to the Arduino. I'll have to find out what this EEPROM feature is. I'l look into it and see if that is causing the problem. Is it something i would want or better to disable it?by Vinculum - Delta Machines
I've just finished building my first 3D printer, the Rostock Mini. Build the mechanics, made the default adjustments to the firmware to account for the mini-sizes and it does move in al the right ways. Joy there! Next step would be te accuratly set the Z-height and start calibrating the buildplatform. However, when i tell it to travel 10mm down from home position it actually travels only 9mm. Soby Vinculum - Delta Machines