I was wondering how tight the belts should be.by mrorange26 - Delta Machines
Yeah looked good but still getting the jumps in the upper part of the print.by mrorange26 - Delta Machines
New head is doing nice prints but still getting slight jumps does anybody have any suggestions on what it could be. On that print I was doing 0.1mmlayer,0.8mm shell thickness,0.6 bottom/top thickness,0 infill,195c temp,100% flow retraction 35mm,4.5mm distance,initial layer 0.3,travel speed 80,bottom layer speed 20mm/s,bottom layer 20mm/s,all others 40mm/sby mrorange26 - Delta Machines
QuoteAndyCart Quotemrorange26 Also can you post a picture of it completely setup thanks. Here it is :- Has anybody designed a new fan mounting or vent for the new all metal hot end andy has been using recently.by mrorange26 - Delta Machines
Ok thanks for info andy I will have a play with the hobbed bolt and settings.by mrorange26 - Delta Machines
Got rid off the print shifting now as my rollers weren't tight,But now its doing this what would cause horizontal lines in the print.its printed at 0.2mm height,0.8mm shell thickness,50mm print speed,40 infill speed,40 top/bottom speed,40 outer,40 inner.by mrorange26 - Delta Machines
Wont work in explorer but works fine in chromeby mrorange26 - Delta Machines
Link not working for me.by mrorange26 - Delta Machines
On cura what is recommended in cooling under minimal layer time (sec).by mrorange26 - Delta Machines
I found the screw on the side so night and tight but not to tight.by mrorange26 - Delta Machines
Should my printer be moving on the wheel like this video link attached.by mrorange26 - Delta Machines
Nice one pugzor,Have you done print yet.by mrorange26 - Delta Machines
Will try that Maso and see what happens.by mrorange26 - Delta Machines
Lol just seen that it can be slid down thanks.by mrorange26 - Delta Machines
I think my z belt feels more slacker than other 2,How do I tighten it up.by mrorange26 - Delta Machines
My shell thickness is 0.8,top and bottom 0.8 and my nozzle is 0.4by mrorange26 - Delta Machines
0.2 height,print speed 50,flow 95%,temp 200c,infill 70%,retraction 40mms 4.5mm,travel speed 80,bottom layer 20,infill speed 40,top/bottom speed 40,outershell 40,innershell 40 Im using cura 15.02.1by mrorange26 - Delta Machines
0.2 height,print speed 50,flow 95%,temp 200c,infill 70%,retraction 40mms 4.5mm,travel speed 80,bottom layer 20,infill speed 40,top/bottom speed 40,outershell 40,innershell 40 Im using curaby mrorange26 - Delta Machines
Why does my cherry pi keep skipping like this in prints.by mrorange26 - Delta Machines
I have just installed a heated bed in my cherry pi.I have a big enough power supply to run it,But im finding that 5 minutes into a print the screen dims and the motors stutter and then the printer stops,Do you think this is a heat issue.by mrorange26 - Delta Machines
I actually put it behind cardboard then aluminium taped on top of that Over the whole of the back of the heated bedby mrorange26 - Delta Machines
I just stuck it to bottom of bed and the reading is exactly the same as my infra red thermometerby mrorange26 - Delta Machines
New head installed,Heated bed installed and working,Seems to be printing well,Thanks andy for help.by mrorange26 - Delta Machines
Thanks andy that worked.I thought that was how you do it but was worried it would wipe everything.by mrorange26 - Delta Machines
Found it in the marlin config file you supplied on the sd card,Do I edit that then upload it to printer,Will I have to recalibrate print head again?by mrorange26 - Delta Machines
I have a cherry pi delta printer and have added a heated bed.i was wondering how I enable it?by mrorange26 - RAMPS Electronics
Can I enable the heated bed and thermistor with gcodes as on my lcd I can only see 1 temp at the moment.by mrorange26 - Delta Machines
I was gonna just stick it on with something in the middle of the plateby mrorange26 - Delta Machines
What command do I need to enable the thermistor and heated bed.by mrorange26 - Delta Machines