good design but for the frame you should realize by yourselfby titeuf007 - Delta Machines
j ai mis une videos a la fin de mon poste tu verras ça explique bien le calibrageby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
on mine i have manuall measure my delta radius which was something 110mm but after auto bed i have 95mm..i ve never understand why i have so many difference..by titeuf007 - General
j ai galeré ss smoothie aussi..car qd tu commences de rien meme si le wiki est bien fait il y a des zones d ombres qd meme mais maintenant je gereby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
le plus simple c est d installer un capteur d autocalibrage j ai galeré des mois avec ce soucis sur ma kossel pour au final avoir un reglage parfait avec un capteurby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
good to know but you big bad point is you low screen compatibility..only one and it cost a lot!! you board is well price but you screen is horrible higher than i can spend for this kind of feature!! it s the only reason why i have not yet buy the duet why don t add a compatibility with skm sbase screen which is really cheap but finally this deux opensource and two board are great we can t go wrby titeuf007 - General
to be honest i have beginning with smoothieware clone from aliexpress because i was my first step in the 32bits world arthur is very great guys which are already here to help us the wiki is very very well made (it could be improve on small points) the board has all features and more we need so for me i will never buy anything else than smoothie i have never had a duet in my hand and i am pretty sby titeuf007 - General
thanks for you help i open a thread on french forum for you kitby titeuf007 - General
Quotepblancart Bonjour à tous Apres des jours de galère j'ai réussi à faire fonctionné ma Prusa (clown chinoise) avec la Lerdge avec adaptateur pour 2 moteurs Z et les and stop Lerdge Mes problèmes ont été résolu suite à la mise à jour du firmware ,passé du 1.1.7 au 2.00 Interface de l’écran complètement différente (je venais juste de m'habituer à l,ancienne Notamment possibilité de personnalisby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
you speak about this version? with this i really love this projet and the new dc42 effector project with pcb great job dudeby titeuf007 - General
QuoteDjDemonD This is where RRF is now helping us immensely with M558 Rx switch where x is recovery time in seconds before probing dive takes place. 0.2sec seems to take care of this problem. Maybe put in a request with marlin, repetier etc to add this feature. Couple that with z max acceleration at 200mm/min and I'm probing without any other slowdowns /macros. on smothieware i think we have thiby titeuf007 - General
Quotedart16 Another piezo sensor board...looks like some level clamping diodes followed by a comparator giving an analogue output that can be adjusted for sensitivity... At £1.68 each I ordered two to find out Piezo vibration sensor this module seem to be good too so it could be the best cheapest and accurate bed leveling or thisby titeuf007 - General
i will buy pcb on uk page could you say me which file i need to print to be compatible with my effector?by titeuf007 - Delta Machines
i have this for my big delta project..and clone hotend v6 could you say me which is good for this effector?by titeuf007 - Delta Machines
do you have the ref from rs components for the good one? it s very interessing project and very accurate sensor! now we need an electonic module to add with this sensor as i can seeby titeuf007 - Delta Machines
where do you buy you piezo?by titeuf007 - Delta Machines
could you say us if you are happy with nimble? could you show us the final result with it mountby titeuf007 - Delta Machines
yes i have seen that i ill test if i have any pb with their NC NOby titeuf007 - Controllers
bon j ai résolu mon probleme... maintenant le g32,g31 enfin bref tous fonctionne...cependant qd je teste apres avec une feuille(apres avoir fait le z max comme indiqué sur le wiki) certaines zones ne sont pas tres bonne... j ai fais le g32 puis le g31 et comme indiqué m500 puis m375 et la j ai ce message qui apparait error:grid size is different read 61 - config 17 ça veut dire quoi?du coup moby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
i adjust tension belt with the up frame for arm lenght i use a calculatorby titeuf007 - Delta Machines
bon j ai resolu mon probleme de tete qui va s ecraser sur le bed lors du g32 mais aussi le fait du palpage que sur une petite zone lors du g31 pour le g31 comme un idiot j avais mal rentré ma valeur de arm radius...donc maintenant il palpe bien tous le plateau pour le g32 c etais plus bizarre..j ai supprimé le fiché de l eeprom et j ai plus eu ce probleme..(je pense qu il ecrasé chaque fois la bby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
bon elle me rend dingue cette carteby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
j ai resolu partiellement mon pb..en effet j ai effacé le fichier eeprom et du coup maintenant qd je fais un g32 elle descend a fond puis s arrete a une certaine hauteur avant de toucher le bed...puis elle fait comme si elle palpé mais sans toucher et fini par allé s eclater sur le bed...arf j y suis presque mais la par contre j ai rien lu sur le wiki dace a une telle situationby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
petit retour sur ma longue series de problemes: -j ai tous reussi a régler c est a dire que mon capteur est bien reconnu(je teste avec la commande des endstops) -mon z home est bien reglé (g0Z0 le papier glisse avec une accroche donc nickel) -le g30 fonctionne aussi..la tete descend ,touche une fois lentement et remonte -le g31 fonctionne aussi avec a la fin de la sequence un message comme quoi cby titeuf007 - RepRap Groupe d'Utilisateurs Francophone
salut arthur j espere que les vacances ce passent bien j aimerai savoir si vous avez une date pour la future carte officiel smoothie?une idéé sur une éventuel dispo?by titeuf007 - RepRap Groupe d'Utilisateurs Francophone
great see you!! so to come back on the thread i found a bug.. you cannot reverse endstop (nc to no) and when you switch on low and high to reverse, it doesn t work...so you need to be right connected in the beginning...by titeuf007 - Controllers
happy to see new users yes new firmware will be release soon apparently ( a friend of mine has already installed it and use it) i will test mine today to see the differenceby titeuf007 - Controllers
my project move on slowly because i am really busy at this moment but i have received almost everything from china now i need to buy in eu shop my motors, bed surface, screws, and others parts that i need my controllers is ready here and will be the lerdge board with auto detection end filament,and all great features (newest firmware available 2.0 with new interface which is more and more userfrby titeuf007 - Delta Machines
une nouvelle version est bientot disponible(version 2.0) nouvelle interface encore plus simple, amelioration du calibrage auto (nouveau algo), une fonction gestion laser sera dispo dans la prochaine mise a jour bref JE conseil vivement cette carte elle est vraiment excellente et un suivi serieuxby titeuf007 - RepRap Groupe d'Utilisateurs Francophone