Show all posts by user
Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"
Re: Kossel Delta xxl build project HELP - 6 years ago
Sorry for delay. It was my mistake, now homing it is working. I'm starting now with the configuration. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Hi David, Could you please help me with homing. Got a homing error, after completing the motor direction test for each axis. I have pushed the home all in the web interface. Thank you, Alexby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David. Z Probe wiring. From pin 5,6,8 on Smart Effector I have 3 wires straight to Duet, based on duer3d. Dozuki instructions. On Miscsolutions.wordpress.com there is no wire connect to pin # 7. Should I leave pin # 7 unconnected ? Witch way I should wire the Z Probe ? Thank you.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David for responding so quickly. I have a 2 wire PT 100 installed. From duet3d.dozuki.com : (You can use a 4-wire PT100 connection from the Effector back to the Duet even if you are using a 2-pin PT100 sensor with a 2-pin connector.) I connect 4 wire on the 8 -way white Molex KK connector and the other end straight to Daughter Board ( MAX Temp V 1.1 ). Should I remove the bridges frby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I used 8 core 22 AWG cable from Smart Effector to Duet The wires for Heater Cartridge are 18 awg . Is 18 gauge wire enough to carry the 2A current ? Should i crimp two conductors of the 8-core 22 AWG cable into each of the hot end heater pins ? Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Effector, viewed from undersideby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
This is where i got so far. Could you please take a look on the wiring to see if I missed something. Endstop and Motors Z = Blue Y = Yellow X = Red Extruder = Greenby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I got it now. I thought it is for a second feet on each tower.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
These are the feet from Home Depot : $ 2.47 These are the screws to attach the Robotdigg carriages to the bearing blocks From Ebay : M3 x 10mm socket cap head screws. I thread the 2 holes on each tower but the distance between the center of the holes is 20mm and the legs are 23mm diameter. You can fit 2 only if you trim them off.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
This is where I got so far.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Hi FA-MAS. I did cut your bottom plate and it fit perfectly including the holes for legs. Bill Kirkelie from pwjet cut it for me for $ 75 the bottom plate and $ 80 for Mic 6 bed. The 713 maker they never send me a quote. Thank you and sorry for delay.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Done ( in the right way ). Next Towers and the Bed.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you so much for your quick response . I will follow your steps and I will post it.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
This is where i got so far. Could you please take a look on the wiring to see if I missed something. Thank you.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I'm almost done with the base. The hard part is coming : Wireing. I'm still looking for someone or a place to print my main inlet front panel and PanelDue 7I screen case.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you Fa-mas. In this case I'm not going to order the IR sensor.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you. Placing the order right now.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Which material you print the adapter for Nimble ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Tolar250 thank you. Very good info. I'm looking for the motor for Nimble. From were you get the bracket for Nema ? Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Hello to everyone. I'm almost done with getting the parts for my project. Tolar250 can you please tell me if you can print nylon, flexible filament with the Nimble ? It looks like Nimble is back in stock and I'm thinking to get one. I found this adapter for the Smart effector : You are using the same adapter ? Do you think the 950 mm drive cable it will be long enough for 1 m tall printer ? Iby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you tolar250. Haydn will ship the arms tomorrow.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you. I found these arms : but I don't know if i should purchase them from this website or straight from Hayden through Google groups.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you tolar250. I start order the parts. From where you order the hayden mangetic arms for your delta printer ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you tolar250. I place the order for HFS5-2024 frame. I'm out of town . What T nut did you use on HFS5 ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you for the plateby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I'm thinking to go with Misumi linear rails. Any recommendations on linear rails and carriage ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
You are right. Thank youby alex773 - Delta Machines