Show all posts by user
Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"
Re: Kossel Delta xxl build project HELP - 5 years ago
You are right,David. I was worried about the heatsink fan. I'm going to put all together tonight and fix the 8-way connector. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you for clarifying this to me.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
This is the fan what I have. This setup is way better than what I have before. Thank you.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I finally got the Fan Duct installed. Please take a look at the attached pictures and tell me what do you think. I do have a question. The fan-output should go through the fan-duct , the rectangular hole , or it's just for orientation ? Mine is not going through. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I will try the fine-point tweezers too , as long I don't have to redo the whole 8-way connector. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you. I don't have a Exacto knife but I do have a very small flat head screwdriver.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I'm going to check out the 8-way connector. I just have to figure out how to take the cables out from the connector.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you FA-MAS. I got the prints in this morning, and I'm going to install them tonight. I uploaded a video about auto-calibration.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
On the parts you have only 40mm fan duct and fan output. No effector-fan-bracket. Can you please share the link for it ? Thank you Nevermind I finally found the bracketby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you. I'm going to print them and post some pictures. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I do have a big issue with the Fan Duct for my Smart Effector. I tried this fun ducts but none of them are fitting in the right position. The fan Is blowing on the heater block.I do have the E3D V6 Hotendby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
It was one time solid green when the printer it was homend. I will upload a video but it is going to take a while, I never did this before. Thank you Davidby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I checked the wiring between effector and the board and everything looks good.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
When I start the printer for the first time G 30 and G 32 are faine. I was able to calibrate with the bed.g you sent me. I don't know what is going on. Thank you for your helpby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I don't know where to look for this issue. I was so excited about this printer and now is not workingby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Something is not right. I changed H parameter from H5 to 7 ,9 , 12 , 14 , 16 and I still have 6 to 13 points not probing the bed. Now the G30 is not touching the bed , is just going up 16mmby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I will do that. I'm starting the printer right now. Let's hope it works.Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you FA-MAS. Right now the H parameter is H5. Should I make it H30 or how much ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you David.This is what I have on Z-probe: ; Z-Probe M558 P5 R0.4 H5 F1200 T6000 ; Set Z probe type to effector and the dive height + speeds G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height M557 R149 S20 ; Define mesh grid What value of H parameter I should have in order to have the G32 command pby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you FA-MAS. It does go through the all motion of probing and only few of them fail to touch the bed.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Yes. G30 works ok , only G32 is not probing. It drives me crazyby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I'm trying to print a small cube and I turned on the printer, G28, G0 Z5 F1800, G30 and G32. When I run G32 I got this error : Z probe was not triggered during probing move. I don't know what I'm doing wrong. G32 it's not working, it is not probing all the points. Is just not working. Something isn't rightby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Thank you so much FA-MAS.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I updated. Now the Starting and Ending scripts are the way it should be ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Starting script G0 X0 Y-149 Z25 F1800 G0 Z0.2 F1800 Ending script: M104 S0 ; turn off extruder M140 S0 ; turn off bed G0 X0 Y0 Z460 F1800 ; home axes -5mmby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
So the best is to have in my Slicer No G code on Starting script. How about the Ending script ? I know you have in Starting script to have the nozzle extruding some filament. What do you have in Ending script ? Could you please help me to set up my Slicer ? This is what I have in Ending script :M104 S0 ; turn off extruder M140 S0 ; turn off bed G28 ; home axes M84 ; disable motorsby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
After G0 Z5 F1800 I moved the nozzle down 2mm, then I sent G30 and G32 and it worked.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
Power off and then on and the web Control is Z0 and the PanelDue is Z470. If I homed again the PanelDue is Z465by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 5 years ago
I moved the nozzle down to bed but it stopped 2mm, 3mm above the bed. Could be the difference between Z465 to Z462.91 ?by alex773 - Delta Machines