Show all posts by user
Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform"
Re: Kossel Delta xxl build project HELP - 6 years ago
I never looked. Where I should check ? I don't have any G92by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I homed again and G0 Z5 F1800. Web Control is 0 and the PanelDue : Z5 Also when the printer is homed PanelDue should be Z465, now is 462.91. I have the homed hight in Config.g set to H470by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I noticed right now when from home position I sent the G0 Z5 F1800, on the way down to the bed the web Control it says 0 then a few times 1000by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
; bed.g ; called to perform automatic delta calibration via G32 ; ; generated by RepRapFirmware Configuration Tool v2 on Fri May 10 2019 065856 GMT-0700 (Pacific Daylight Time) M561 ; clear any bed transform ; Probe the bed at 12 peripheral and 6 halfway points, and perform 6-factor auto compensation ; Before running this, you should have set up your Z-probe trigger height to suit your build, inby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
; homedelta.g ; called to home all towers on a delta printer ; ; generated by RepRapFirmware Configuration Tool v2 on Sat Mar 30 2019 20:58:40 GMT-0500 (Central Daylight Time) G91 ; relative positioning G1 S1 X676 Y676 Z676 F1800 ; move all towers to the high end stopping at the endstops (first pass) G1 X-5 Y-5 Z-5 F1800 S2 ; go down a few mm G1 S1 X10 Y10 Z10 F360by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Sat Mar 30 2019 20:58:40 GMT-0500 (Central Daylight Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M665 R179 Lby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Now I sent G28 and G0 Z5 F1800. All good. When I sent G30 the nozzle is not touching the bed and if I keep sending G30 the nozzle is going up.After I sent G0 Z5 F1800 the Z probe on the web Control is blinking a few times 1000 then is 0by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you FA-MAS. I did exactly what you said. When I sent G 32 the nozzle is not touching the all points and I got this error : Z probe already triggered at start of probing move. Compensation or calibration cancelled due to probing errors.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David for your quick response. I did what you said. I home the printer and I sent G32. The nozzle goes down halfway and starts execute G32 ( Z probe was not triggered during the probing move. Compensation or calibration cancelled due to probing errors ) . I tried a few times and then finally go through. When is printing the green light for probing it stays solid green. this is what I hby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I finally figured out what was wrong with the extrusion. Now the extruder it is working good. I was able to calibrate the E steps/mm and trying to print. When I try to print the nozzle was to close to the bed. I heat up the bed to 60 C and the hotend to 190 C , move down the nozzle until I could just slide a piece of paper under the nozzle with some resistance. Then I sent G92 Z0 and G1 Z5 and G3by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Yes , the hot end fan turns on when the temperature exceeds 45C but no lightsby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Hi David. I know you remember I was having problems with the temperature reading on the Hotend. I figured it out. I replaced this plug and now I have the bed temp 23 C and the Hotend 23.7 C. I installed everything back and I don't know why the Smart effector lights are not working anymore. There is any way to make the work again ? Thank you.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
The Nimble documentation says : For 32 but boards start at around 2700 steps/mm at 1/16 microstepping. This is what I have : M92 X200.00 Y200.00 Z200.00 E2700.00 ; Set steps per mmby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Ok FA-MAS , good to know. Thank you and I will try your recommendation tonight.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you blt3dp. I will try to get it done tonight. Please guide me through this process. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you blt3dp. Do you still have the STL file for the Cube ? I'm going to do this test but first I have to fix the extrusion problemby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David. I'm using the Nimble extruder with this stepper motor : ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S0 ; Drive 2 goes backwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I1by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
For the last two weeks I was trying to print and calibrate the printer . I have a problem with the extrusion. The print is working good for not more than 25% then the printer is printing with no filament. I don't know where should I look. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
This is my first print. I'm so happy. It's a bad print but it is a PRINT.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you FA-MAS and sorry for delay. I adjusted the homed height using the G92 Z20 . Do you have G0 Z5 F1800 in Bed.g before G30 and G32 or you send it manually after you turn on the printer ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you FA-MAS. How can I lower the speed to move the nozzle down towards bed ( the speed right now it's crazy fast). What settings I have to change ? Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you FA-MAS. I set my homed height from 469 mm to 459mm, then I moved the nozzle down and it stopped 10mm above the bed. Then I sent G2 Z20 and I got this Error : G2/G3: missing I or J parameter . Should I send the M564 S0 to disable axis limits ?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I got the Simplify 3d software last week and I was trying to print something this weekend with no success. I Upload the G-code File and then I run it. When the printer it is ready to print the Hotend it goes crazy fast down and smash into the bed . I'm afraid is going to break the glass. Please advise what settings I should change in order to be able to print finally something. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David for your response. Sorry for delay. I checked what you said and I found a bad connection to the daughter board. When I checked the daughter board with the supplied 100 ohm resistor I have a reading of. - 1.3 degree C. The wire for PT100 are 22 gauge in a 4-wires connection. Now I have 24.9 on the Bed and 28.7 on the Hotend. Let's hope it is all good now. Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I unplugged the PT100 from Smart effector and plugged it back on and the temperature for Hotend now it is 26.5 C and the bed is 23.3 C. Now it is working good but I'm not sure where is the problem.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David. I'm going to try all of your recommendation to see how this can be fixed.by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Thank you David for your input. If you remember in first place when I first started the printer the difference between the bed and hotend it was almost 4 degrees C. There is no option to fix this problem ? Thank youby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I'm using the E3D PT100 sensor in 4 wire configuration with PT100 daughterboard. My config.g file: ; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Sat Mar 30 2019 20:58:40 GMT-0500 (Central Daylight Time) ; General preferences G90 ; Send absolute cooby alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
Something I not going right. When I turn the printer on the hotend temperature it is 38 degree C , but the hotend is off and cold . I checked the connection and everything looks good. Where is the problem?by alex773 - Delta Machines
Re: Kossel Delta xxl build project HELP - 6 years ago
I'm going to try later to change something. Thank youby alex773 - Delta Machines