Quotemurmurian If you really planning on using it only a couple of times, wouldn't it be better to just order outsource your prints to some 3d printing company? Some of them even have industrial grade hardware with way better print quality and material selection a mere consumer peasants like us can hope to buy in our lives. I have to AGREE, you don't buy a cow when you only want a couple glassesby rhmorrison - General
Der Rechte?by rhmorrison - Allgemeines
Woher hast du die hexoginal aluminium platte? Ich hatte auch gern genau so eine - Runde heizmatte ist schon bestellt!by rhmorrison - Projekte
What FW? What HW? How connected? A picture?by rhmorrison - General
Ich suche genau das gleiche (für meine HEXAGON delta drucker), am besten schon mit thermistor eingebaut!by rhmorrison - Schwarzes Brett
Use AWK, every version of UNIX has it!by rhmorrison - Slic3r
I still need to change the diameter of the lower cylinders. If you look at the specifications k is the radius of the bottom curves but it was used as the diameter. Would have done it already but I currently don't have a working computer at home.by rhmorrison - OpenSCAD
No, it is the sin(x) that is very close to tan(x) where x is a small angle but he didn't multiply by the hypotenuse, he just used cos(x) which is a factor (adj/hyp) and not a length! Dividing mm by mm is unit less.by rhmorrison - OpenSCAD
Sonne plus Motorrad vibration ist die absolut härte Test für PLA. Ich hoffe das du deine Navi nicht auf die Strasse verloren geht... Ich druck mal die Daumen.by rhmorrison - Allgemeines
Quotecvera1945 I HAVE BAD EYES AND HAVE A HARD TIME LOOKING AT SMALL LETTERS ON THE SCREEN Then you should use BIG FONTS or set your screen resolution such that you can read the letters on your screen!by rhmorrison - General
Im Summer in der Sonne wird es zu warm für PLA, es wird weich! Beim Motorrad ist es am eigens besser als beim Auto, da kann es leicht bis 70°C werden, ab 60° ist PLA weich. Es ist auch fester (wenn mann keine spezielles PLA wie "soft" benutzt) sprich hält vibrationen und plötzliche impulse nicht ganz so gut wie ABS.by rhmorrison - Allgemeines
Wenn du teilen für dein Motorrad drucken willst den brauchst du ABS oder ein andere plastik als PLA!by rhmorrison - Allgemeines
And HERE a version with dmould's suggestion implemented (an optional gap): // dsub.scad // // D-Sub connector library by 'dpeart' function db_conn_table(idx) = // idx == "db9F" ? [12.50,11.10,6.53,2.11] : idx == "db9R" ? [12.50,11.10,5.72,3.35] : idx == "db15F" ? [16.66,15.27,6.53,2.11] : idx == "db15R" ? [16.66,15.27,5.72,3.35] : idx == "db25F" ? [23.52,22.15,6.53,2.11] : idx ==by rhmorrison - OpenSCAD
One last change needed: // dsub.scad // // D-Sub connector library by 'dpeart' function db_conn_table(idx) = // idx == "db9F" ? [12.50,11.10,6.53,2.11] : idx == "db9R" ? [12.50,11.10,5.72,3.35] : idx == "db15F" ? [16.66,15.27,6.53,2.11] : idx == "db15R" ? [16.66,15.27,5.72,3.35] : idx == "db25F" ? [23.52,22.15,6.53,2.11] : idx == "db25R" ? [23.52,21.39,5.72,3.35] : idx == "db37Fby rhmorrison - OpenSCAD
Jede Editor hat eine Such funktion. Suche nach "TEMP_SENSOR_BED" und "MOTHERBOARD".by rhmorrison - Elektrik & Elektronik
I would make the following changes to be able to use properly it as a library: // dsub.scad // // D-Sub connector library by 'dpeart' function db_conn_table(idx) = // idx == "db9F" ? [12.50,11.10,6.53,2.11] : idx == "db9R" ? [12.50,11.10,5.72,3.35] : idx == "db15F" ? [16.66,15.27,6.53,2.11] : idx == "db15R" ? [16.66,15.27,5.72,3.35] : idx == "db25F" ? [23.52,22.15,6.53,2.11] : idby rhmorrison - OpenSCAD
Yes, exactly in the direction I meant! b = db_conn_table(conn)[0]; d = db_conn_table(conn)[1]; f = db_conn_table(conn)[2]; k = db_conn_table(conn)[3]; shouldn't this be instead b = conn_dimensions[0]; d = conn_dimensions[1]; f = conn_dimensions[2]; k = conn_dimensions[3]; Since you already used: conn_dimensions = db_conn_table(conn); Also I would translate the whole thing down h/2 so itby rhmorrison - OpenSCAD
Wie wäre es mit "U2D3" or "U23D"?by rhmorrison - Offtopic
There are some OpenSCAD libraries around but I couldn't locate one for rs232c (db-N) connectors. OpenSCAD User Manual/Libraries Libraries · openscad_openscad Wiki · GitHub But then what do you really need? You obviously want to make a cutout in a panel for a db-15 connector (a good starting place is HERE). Using the above HERE link you can easily create a module to generate the needed form.by rhmorrison - OpenSCAD
Wenn du nur einmal das machen willst geht das mit Notepad++ aber wenn du schon ein zweite mal das machen will bin ich schneller weil ich ein AWK skript geschrieben hat. Dauert vielleicht länger als es per hand zu machen (einmal) aber es ist bestimmt schneller als es zweimal von hand machen zu mussen (und auch zuverlässiger). Als Programmierer macht man ein Aufgabe nur einmal (aber richtig).by rhmorrison - Software
Die zwei GCode Dateien anhängen und beschreibe wie die gemischt sein sollte (beim layer #).by rhmorrison - Software
Da solltest du ein Programm dafür schreiben! Für so eine Aufgabe werde ich personlich AWK nutzen, aber Perl, Python oder jede Sprache das du gut kennst werde reichen.by rhmorrison - Software
WELCHE FIRMWARE! Nicht welche HARDWARE und nicht welche LCD - Welche FIRMWARE, z.B. Marlin, Repetier, Sprinter, usw...by rhmorrison - Software
Stimmt, aber du hast kein % zeichen benutzt! QuoteWurstnase Na sag ich doch, Skalierung auf 1000 ;-) Gelesen kann nur was geschrieben ist!by rhmorrison - Schwarzes Brett
YES - Skeinforge Craft - Skin! For example use a layer height of 0.2mm but skin is set to 0.1mm!by rhmorrison - Experimental
Was für filament resten? Ich mache es wie beschrieben von Kulturfolger.by rhmorrison - Allgemeines