Show all posts by user
All of China!
Page 1 of 2
Pages: 12
Results 1 — 30 of 38
안녕하세요.
저는 홍콩에서 Reprap 판매하고있는 크리스씨 라고합니다.
현재 제가 새로운 개선형 "Prusa" 3D printer 크트 공금가능합니다.
"Prusa" 프린트 parts (PLA + ABS : Extruder 부품)
ABS 프린트 - 약 2.5시간
PLA 프린트 - 약 3시간
관심이 있은 분이 매일으로 과 MSN으로 연락주십시오.
여기에 많이 설명하지못했습니다.
제가 중국어로 Blog 과 Taobao web가게 참고보세요.
Reprap 개성행 "Prusa" 키드 부품 보함
1.) PLA + ABS (Extruder, X-Carriage) 프린트 부품세트.
2.) 모든 M8 Rod + Thread Rod
3.) 모든 Bolts & Nuts.
4.) X,Y a
by
tv7957ht
-
Korea RepRap User Group
你好, 我是Chris... 我的blog內是舊供應的Gen3 控制板, 這個5月尾我有Arduino Atmega1280 + Ramps板(Sprinter Firmware) + StepStick A4988 全套電子控制供應, 有興趣可send email 我我聯絡. - chris_hy88@hotmail.com
by
tv7957ht
-
Hong Kong RepRap User Group
the line shown "DEBUG: GCode opening port COM1 [0.178s/168ms] "
make sure you setting a right COM port at reprap host. if your using windows system go to searching
C:\Documents and Settings\Administrator\.reprap
inside there your need to open a file " reprap.PROPERTIES" and change a BaudRate setting from 19200 --> 57600
by
tv7957ht
-
Sanguino(lolu)
I had trying a different firmware as follows in my Sanguinololu 7.0 board.
1.) reprap-mendel-20100628:Firmware+ReprapHost = (ReprapHost : Can't go into control panel), (RepSnapper : Can't connected keep going M105)
2.) reprap-mendel-20110207:Firmware+ReprapHos t= (ReprapHost : OK going into control panel, only can control +movement on X,Y,Z just
by
tv7957ht
-
Sanguino(lolu)
you can find baudrate setting at configuration.h file inside a Five_Gcode_Interpreter folder.
by
tv7957ht
-
RepRap Host
Hi, I'm just finished of building my first Sanguinololu 7.0 PCB board and i can successful to upload a ATmegaBOOT_644P bootloader
and no problem uploading a firmware into a chip through by on-board FTDI232RL chip which is solder at the bottom of a PCB. However, until to now, I stiil can't to connect a board to "Reprap Host" or " "RepSnapper" respectively.
I had tried by using different combin
by
tv7957ht
-
Sanguino(lolu)
한국 Reprap DIY 조립 관심자들은 안녕하세요. !!!!
저는 naver에서 Reprap 관려자료 Blog 조금만 자료를 써어 참고하세요.
by
tv7957ht
-
Korea RepRap User Group
你好, 我已經send 左email比你, 我可以提供RP零件及Reprap電控板給你.
可加我MSN : chris_hy88@hotmail.com or QQ : 1458672323
by
tv7957ht
-
Hong Kong RepRap User Group
Where can i find a new Reprap host software ?
by
tv7957ht
-
General
I had updated a new "official" firmware -
hope to using bang-bang control for my extruder's thermcouple, however, after uploaded a new-firmware it don't connect to
Reprap-host software. (i using ver. is "20100806") .... anyone had same problem like me ?
Now, i only the way is go back to old hacked firmware.....
by
tv7957ht
-
General
Thanks a lot ! nophead..... you are the best.
Also, thanks Traumflug ... by the way, why i'm not using Reprap host software, because i using a DC motor extruder for my Huxley.
Thanks.
by
tv7957ht
-
General
Hi, I had a problem is how to config & calulate the x,y,z axis scale at Replicator G.
I'm know that i need to config axis scale in machines.xml but i have no idea what value i should fill it on.
(See as follows)
axis id="x" length="300" maxfeedrate="5000" scale="11.767463"/ <-----(For M6x1 thread rod what value i need to put on ?)
axis id="y" length="300" maxfeedrate="5000" scale="11.7
by
tv7957ht
-
General
I had a problem of using Skeinforge to generate Gcode. I dont know why a Skeinforge to generated a code without extuder fliament at first layer in perimeter outline at sometime, For my little knowledge in Gcodes, its seem Skeinforge making a wrong Gcodes E setting for first layer of perimeter.
Also, I had tried to changed a "Thread Sequence Choice" to "Infill > Loops > Perimeter" than its
by
tv7957ht
-
General
Finally, I read a older post and saw Wade said he set is firmware with "acceleration turned off"
than i go to change my firmware setting and i was so happy its works..... my object finally got corrected printing.
Hope it would help someone if got this problem.
(If you using the "FiveD_GCode_Interpreter " firmware.)
1.) First open your arduino0018 IDE (what i using now.) than open a "configurat
by
tv7957ht
-
General
Checking your gcode file and take a looking a M104 command is being set.
Also you can see and know more about Reprap Gcode.
by
tv7957ht
-
RepRap Host
Hi, I just tried to add homing.gcode with M105 command and seem not working, may be i did some wrong ?
can you tell me how much of Z max feedrate i need to set.
I've tried 0.002, 0.1, 4, until to 10 mm/s .... all of them its seem make z axis step very fast and cause no movement on z axis.
Thanks.
by
tv7957ht
-
General
Do you think is't any problem on a stepper motor ? hardware problem cause this happen ? but how can explain why when i printing a 15x15x25 test object is correct ??????????
Thanks a lot !
by
tv7957ht
-
General
As my last post i had resolve a Z axis about it cannot lifting up in correct printing position and nophead advise me that its seem setting too fast of Z axis and losing stepping on Z motor, than i go to config a lower value of "Maximum Z feed Rate = 0.5" in Skeinforge, and its seem work fine after changed it. However, After i tried a few print test than i found a very stranger problem and i canno
by
tv7957ht
-
General
Hi, nophead thank you again of your advise, I just keep ""#define Z_STEPS_PER_MM 833.398 "" in configuration.h and i just simply revise a setting Skeinforge Speed Setting ---- "Maximum Z feed rate (mm/s) = 0.5" than my z-axis stepper motor move correctly.
Thanks a lot !!!!
by
tv7957ht
-
General
Hi, I had a problem in printing G-code file which is generated from skeinforge, the problems is my mendel z-axis seem dont lift-up after finish laying each layer. (I tried put my hand on a threaded rod, in fact it just lift-up very little, not enough space to lay another layer on top.)
I'm not sure is't may be a wrong setting of configuration.h" at Five_GCode_interpreter.
#ifdef MENDEL
// def
by
tv7957ht
-
General
Hi, Stoffel15 & nophead .... Thanks a lot !!!! it is very very helpful......i can running a g-code and my extruder stepper motor is spinning....
By the way, because of i'm using the old version of Skeinforge. So that's why i dont see a "Carve" -- "Dimension" to config it..
Thanks a lot !!!!!
by
tv7957ht
-
General
Hi, nophead thanks for reply, however, I not so sure you tell me ...But, I had already make FiveD "true" in preferences and extruder stepper motor still dont spinning....So, as you advise am i need to do something more for the skeinforge ?
Thanks.
by
tv7957ht
-
General
Hi, I did a modifications as a reprap design, I also connected a (SDA to D10) & (SCL to D9) already, But, I have no idea why the extruder stepper motor dont spinning when running G-Code in reprap-host software, but its can spinning in reprap-host console "extruder" button.....
I'm thinking about is't my wrong G-code cause this problem. ?
by
tv7957ht
-
General
Hi, Sorry, i dont understand what is meaning of "make dimension on" can you tell me more detail how to resolve my problems.
Because i'm not very good in g-code knowledge.....
**Today i just changed my g-code by using M108 S255 to control the extruder, but after running from reprap-host software, one chip (two LED was ON)...... I'm thinking about that may be reprap-host software only run my g-co
by
tv7957ht
-
General
Hi, I think we had a same problem in our exturder stepper motor... my post :
For your case have you tried load a gcode to run a machine ? is't also blink 4 LED ?
by
tv7957ht
-
General
Hi, I just completed my Mendel assembled, and i had done my x,y,z axis test running, and extruder
stepper motor test running (both at reprap-host software console) and its goes fine,
than, i've generate a g code file from skeinforge and loaded in reprp-host software and x,y,z
axis worked fine however, the extruder stepper motor didn't run when i running a gcode file.
can anyone can help me a
by
tv7957ht
-
General
Hi, I just found a way to solved my problem. I was just did follows.
1.) re-uploading a bootloader to motherboard & extruder board.
2.) upload a "FiveD_GCode_Interpreter" firmware to motherboard. (http://reprap.org/wiki/Microcontroller_firmware_installation)
3.) upload a "FiveD_GCode/Extruder" firmware to extruder board. (http://reprap.org/wiki/Microcontroller_firmware_installation)
4.) usin
by
tv7957ht
-
RepRap Host
Hi, nophead..... Thanks for reply, I was uploaded a "reprap-gen3-firmware-1.2" firmware to motherboard and extruder board.
attached with a screenprint of debug windows shows information.
i tried a lot of method but the reprap host software is still keep hang my computer when i wand to cliick any button in console.
Please advise me... what happen !!
by
tv7957ht
-
RepRap Host
Page 1 of 2
Pages: 12