Show all posts by user
Everybody here is a developer. Share what you are doing !
Page 1 of 2 Pages: 12
Results 1 — 30 of 35
Re: how to use the bare conductive paste - 10 years ago
Thank you very much for the reply. I saw the video on the internet for use of bare conductive electrical paint. it looks simple as that we can try it on the paper to draw a circuit with the electrical paint. i tried the same thing on the paper but it doesn't work at all. moreover i want to run the 5th motor for the dispenser without using the heater and thermistor so what changes do i need to makby Tinkusharma - General
Re: how to run the 5th motor without using the heater and thermistors - 10 years ago
Is it possible to run the motor without the use of thermistor and heater, please let me know asap. Thank you very much.by Tinkusharma - General
how to use the bare conductive paste - 10 years ago
hello, i am doing a 3D printer and i want to use the bare conductive paste for the additional dispenser unit. i tried to use the conductive paste on a paper to test whether it can work or not or it can glow the LED. also try to glow the directly with the battery it was glowing. so please let me know how to use the bare conductive paste. thank you very much.by Tinkusharma - General
how to run the 5th motor without using the heater and thermistors - 10 years ago
hello, i am doing a 3d printer prusa mendal i2. i added another dispenser to the 3D printer that do not have any heater or thermistors. i want to run the 5th motor for the additional dispenser so what i need to change in the firmware to get it.moreover i tried to test and it by prevent the dangerous extrude, it was working but i have no need to use the heater and thermistors for the dispenser. sby Tinkusharma - General
Re: second extruder motor not working - 10 years ago
thank you very much, actually i am doing my project and i have a very limited time for this. is there any other way to start the motor without using the heater and the sensor. please give me your suggestion asap. thank you very much once again.by Tinkusharma - General
Re: Dual extruders on ramps 1.4 - 10 years ago
thank you very much for posting the file, i will try with it. thank you very much once gain.by Tinkusharma - General
second extruder motor not working - 10 years ago
helllo, i am doing a prusa mendal i2 3d printer that has the ramps 1.4 and arduino mega 2560. i modified the firmware for the second extruder. the heater and the sensor is working properly but the extruder motor doesn't work. please give your suggsetions. and will it be possible to run the motor without using the heater and sensor. i just want to run the motor for the second dispenser. here is myby Tinkusharma - General
Re: error with the compile the marlin for two extruder - 10 years ago
Thank you very much, i definedt the temperature sensor 1 and motherboard as EEB, and EXTRUDERS AS 2, heaters and sensor is working properly but the motors is not working for the second extruder. please give me any solution or suggestions asap. thank you very much once again.by Tinkusharma - General
Re: error with the compile the marlin for two extruder - 10 years ago
thank you very much. i made the changes to the firmware and compiled it. but the new problem is how to test that both extruder with the pronterface because it shows only one extruder. please give your suggestion or advise. thank you very much.by Tinkusharma - General
Re: error with the compile the marlin for two extruder - 10 years ago
I understood the thing, but where do i need to make changes in the firmware because i am unable to find the location. please advise me asap. thank you very much.by Tinkusharma - General
error with the compile the marlin for two extruder - 10 years ago
hello, i am doing a 3D printer that has one extruder with heater and sensors. but i am using a solder paste dispenser that has no heater, no thermistor so i am facing a problem with the compiling. the error is below, Arduino: 1.6.0 (Windows 8), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from Configuration_adv.h:659:0, from Configuration.h:943,by Tinkusharma - General
Re: Dual extruders on ramps 1.4 - 10 years ago
I tried with it but its not working . Please post the file. Thank you very muchby Tinkusharma - General
Re: Dual extruders on ramps 1.4 - 10 years ago
Hello everyone, Could you please attach you configuration h file for the dual extruder set up for the 3d printer. I will be very thankful to you. Thank you very much.by Tinkusharma - General
Re: **HELP!!** DUAL EXTRUDER MARLIN SET UP - 10 years ago
Hello, Could you please attach your configuration h file of fual extruder set up. It could be very helpful for me because i am doing the same thing. Thank you very muchby Tinkusharma - Developers
Re: programm the dispenser and extruder - 10 years ago
Arduino: 1.6.9 (Windows 10), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from sketch\Configuration_adv.h:689:0, from sketch\Configuration.h:1129, from C:\Users\Rinku\Desktop\Marlin-RC\Marlin\Marlin.ino:37: SanityCheck.h:437: error: #error HEATER_1_PIN not defined for this board. #error HEATER_1_PIN not defined forby Tinkusharma - General
Re: programm the dispenser and extruder - 10 years ago
hello, i am trying to set it but it say it needs an temp sensor. exit status 1 #error TEMP_SENSOR_1 is required with 2 or more EXTRUDERS. even i set up another temp sensor to it. please give me any suggestions and if you have the same type of file please forward it to me. thank you very much for the help.by Tinkusharma - General
Re: programm the dispenser and extruder - 10 years ago
Thank you very much for your response but when i am trying to select the extruder as number 2 and on compiling its shows me error for the temp sensor. So could you please give me any programmed file for the 3d printer.by Tinkusharma - General
programm the dispenser and extruder - 10 years ago
hello, I am doing the 3d printer prusa mendal i2. I want to incorporate a solder paste dispenser unit to this, this dispenser unit will have the another motor and no heater or sensor . I want to know how to program these with marlin and currently I am using the Arduino mega 2560.so I want to know how to program it with the marlin. thanksby Tinkusharma - General
Extruder start before its prints - 10 years ago
Hello Everyone, I want my 3d printer extruder motor to start before its starts printing or it could be possible to start the extruder motor after bed get heated and the quality of printed parts is poor so please advise me about the slicer settings and the extruder settings. I am using the PLA filament 1.80 dia for printing the 20 mm test cube part. Please give me any suggestion. Thank you very muby Tinkusharma - General
Issue with z axis home position - 10 years ago
Hello, I am working on prusa mendal i2 and its z axis home position is not working properly, when try to give the z home value its start making noise and work by z axis switch moreover it only goes for 10 rotations only althought the pressing the z axis switch. So please advise me any suggestions about it. Thanksby Tinkusharma - General
Re: temp for the j head mkv hot end set - 10 years ago
I am using the 100k thermistors so i used the table for temp bed 0 5. Am i correct?by Tinkusharma - General
temp for the j head mkv hot end set - 10 years ago
hello I am doing the 3d printer project and in marlin programme I set the heater temp 0 5 and I am using the pronterface to run it but when I set temp of the heater to 230 it shows me 230 while it has approximately 135 c temperature only when I check the temp by thermometer so anybody can advice me whats the problem. thanks.by Tinkusharma - General
Re: Selection of extruder - 10 years ago
Its about build a 3d printer and incorporate the two different dispense unit to it, So which solder paste dispenser is good for the project. Thanksby Tinkusharma - General
Selection of extruder - 10 years ago
Hello, I am doing the 3d printer project for my master course can anybody advice me which solder paste extruder is best and cheap for the 3d printer of prusa mendal i2. Thanksby Tinkusharma - General
Re: error in the program - 10 years ago
Hello, Actually the previous file used was sprinter firmware with the pronterface. Its verify, compiled and iploaded to arduino. I connected the 3d printer using the pronterface. Its shows connected but the motors is off the graph is working but its not heating the bed and nozzle . Help me to come out of this problem. Thanksby Tinkusharma - General
Re: Issue with connceting repsnapper to printer - 10 years ago
even I checked the connection of the power supply its ok and shows me 12V.by Tinkusharma - General
Re: Issue with connceting repsnapper to printer - 10 years ago
I tried to connect it by using the sprinter and the pronterface its shows me online but the motors is off, graph is responding, but when to give movement to axis its shows me something like this, onnecting... Sprinter 1.3.22T / 20.08.2012 start Printer is now online. SD Start SD init fail Soft PWM Init Planner Init Stepper Timer init Free Ram: 4649 Plan Buffer Size:1152 / 16 X:0.00Y:0.00Z:0.10E:by Tinkusharma - General
Re: error in the program - 10 years ago
I try to use the sprinter firmware and the pronterface to connect the 3d printer its show me something like this even the graph is working. Connecting... Sprinter 1.3.22T / 20.08.2012 start Printer is now online. SD Start SD init fail Soft PWM Init Planner Init Stepper Timer init Free Ram: 4649 Plan Buffer Size:1152 / 16 X:0.00Y:0.00Z:1.00E:0.00 X:0.00Y:0.00Z:2.00E:0.00 X:0.00Y:0.00Z:3.00E:0.00by Tinkusharma - General
Re: Marlin won't compile on my PC - 10 years ago
sorry the previous attached file isn't the right one. the right one file is #define CONFIGURATION_H #include "boards.h" // This configuration file contains the basic settings. // Advanced settings can be found in Configuration_adv.h // BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration //==================================================by Tinkusharma - General
Re: error in the program - 10 years ago
I attached the requested file, its shows me some thing like this when I connect the printer by using the pronterface . Connecting... start Printer is now online. echo:Marlin 1.1.0-RC6 echo: Last Updated: 2016-04-24 12:00 | Author: (none, default config) Compiled: Jul 6 2016 echo: Free Memory: 5202 PlannerBufferBytes: 1232 echo:Hardcoded Default Settings Loaded echoteps per unit: echo: M92 X80.by Tinkusharma - General
Page 1 of 2 Pages: 12