Show all posts by user
Support for the quite nice RAMPS Electronics. See also http://reprap.org/wiki/RAMPS.
Re: Slic3r patch - 12 years ago
ooops! Tee Hee . Thanks for the info! The instructions are quite clear.by spaceman - Slic3r
Slic3r patch - 12 years ago
Can someone walk me through applying a patch posted on Github?by spaceman - Slic3r
Re: Advanced Tab Clarificationof Version 0.8.4. - 12 years ago
spaceman Wrote: ------------------------------------------------------- > When we turn off any solid layers, we > get perfect prints. Would the bridge flow ratio > have any bearing on the infill/solid layer? > Does anyone know if the bridge flow ratio would reduce the solid layer plastic amount? Is anyone else having solid layer issues within their first 3 layers?by spaceman - Slic3r
Re: Advanced Tab Clarificationof Version 0.8.4. - 12 years ago
QuoteI have to ask. Why are you using the percentage? The best new feature in my opinion is the fact you can enter those as actual widths and never have to adjust them again when you change layer heights. We tried printing with actual widths (mm) and the perimeters and brims printed fine but the infill/solid gave terrible results. They were bloby and torn. We are tried to use % to see if it wouby spaceman - Slic3r
Advanced Tab Clarificationof Version 0.8.4. - 12 years ago
I am trying to understand, in the Extrusion area of the Advanced tab of Version 0.8.4, the relationship in % between the settings and the layer heights. Is the below correct? Extrusion Width = % of Layer Height (Print Settings Tab) First Layer Extrusion Width = % of First Layer Height (Print Settings Tab) Perimeter Extrusion Width = % of Layer Height (Print Settings Tab) Infill Extrusion Widthby spaceman - Slic3r
Re: Slic3r and DLP - 12 years ago
Thanks for the info. I'm poking around to see if I want to experiment with this tech too. Does anyone out there have a working DLP printer? What software do you use to control it? I've looked at the lemoncurry site and I've seen Junior Veloso site but it's all kind of scattered about and I'm trying to condense it.by spaceman - Slic3r
Slic3r and DLP - 12 years ago
Does anyone know how to make slic3r output the slices for DLP projection?by spaceman - Slic3r
Re: Slic3r and pronterface - 13 years ago
Does anyone know the pin out assignments of the Makerbot extruder board? I've finally got printerface to communicate with my machine but when I send a heatup command, nothing happens. I can't figure out what pins should be assigned to the thermocouple. I reads the temps but doesn't heat.by spaceman - Slic3r
Slic3r and Makerbot Gcode - 13 years ago
I have a makerbot hardware machine and am trying to use slic3r. I have noticed that when I set a bed temperature that the wrong M code is produced in the Gcode. Below is the beginning of my code. The second last line states M190 S70. But it should be M109. Can anyone else confirm this? ; generated by Slic3r 0.7.1 on 2012-03-27 at 19:39:15 ; layer_height = .254 ; perimeters = 2 ; solid_layersby spaceman - Slic3r
Re: Slic3r and pronterface - 13 years ago
Greg Frost Wrote: ------------------------------------------------------- > Is he saying you need: "C:\Program > Files\Slic3r\Slic3r.exe" ? Problem solved. I needed to put double quotes around the path because I have spaces in my path names. The follow-up qould be, does anyone know if this works with Makerbot hardware? I can't seem to connect to my machine. I am using the same port andby spaceman - Slic3r
Re: Slic3r and pronterface - 13 years ago
Hi, Thanks for your quick response. That is my path. It is C:\Program Files\Slic3r. but it doesn't work.by spaceman - Slic3r
Re: Slic3r and pronterface - 13 years ago
I know this an old subject but I'm new to Slic3r. So, I can't get Pronterface to work with Slic3r either. It won't accept the path and gives me this error: Entering skeinforge settings: C:\Program Files\Slic3r --load C:\Program Files\Slic3r --ignore-nonexistent-config Skeinforge execution failed: The system cannot find the file specified Here are the 2 fieldsI have entered according to thby spaceman - Slic3r
Skeinforge with 2 extruder heads - 14 years ago
Hello, Can skeinforge handle a machine with 2 print heads. I was wondering if I could build a machine with 2. One for ABS and one for support material. If it can, is there a difference in the Gcode for which extruder is turned on?by spaceman - Skeinforge
Re: M codes crashing reprap host - 14 years ago
If I needed to change the axis that skeinforge uses to fire the extruders, could I do this by changing the replace.csv file? I need to use axis 'A' rather than the 'E' command currently used by skeinforgeby spaceman - Skeinforge