Thank you for your help! I just fixed it. Good that you pointed me towards potential wiring issues! The connection of the end stop came loose and constantly indicated that it was hit. Hence, the RAMPS firmware did not allow motion in the negative y direction. After reconnecting the pin, the end stop behaved correctly and everything moves as it should! Hence, the problem is solved!von mardy3d - General
Hi, i am working on a major electronics upgrade for my old MakerFarm i3v 10" with a RAMPS1.4. After adding a few cables here and there as a first part of the major upgrade, I found that the y stepper only spins in one direction, the +y direction to be precise. For the other direction, the motor does not move and only makes sounds similar to a stalling motor. Have you ever encountered somethingvon mardy3d - General
Thanks for the explanation. That makes the whole set-up even easier by just hooking one diode in the power line. Yeah, I have noticed that there are no wood printers anymore. However, I got mine quite some years ago so that I am confined to using my wooden printer for now :-/. I was considering re-building it by using aluminium extrusions. But that needs to wait until it is delivering a good privon mardy3d - General
Quotedc42 Something like or . It will get quite hot, so make sure that air can circulate around it. That's interesting as it's not what I expected it to be. I searched for some tutorials of how to build my own rectifier unit from these diodes. I found a few videos, such as: , , and that describe how to assemble the 4 diodes to obtain a rectifier unit. Is that what you had in mind as well? I wvon mardy3d - General
Thank you very much for your replies! Again, it helped me a lot! Avoiding such a large transformator is a good idea. Quotethe_digital_dentist why not just use 110V line input for it and skip the transformator What do you mean by the 110V line? In the country I live in (Germany), there is no 110V line according to my best knowledge. Quotethe_digital_dentist put a rectifier in series with the hvon mardy3d - General
Dear all, thank you very much for the help of all of you, it really helped sorting my thoughts! I read everything thoroughly and am planning the next steps now. I would have the following questions and will summarise my whole stack of ideas in the end. I would have the following few remaining questions. Maybe you can help me? :-) I don't know the advantages and disadvantages of using a transfvon mardy3d - General
Dear RepRappers, my setup: A modified MakerFarm i3v 10. I switched to a 230V 500W heatbed with ~5-8mm aluminium bed some time ago. TL;DR: My heatbed is quite slow. What is your heatbed setup and how fast are they? I have two heat beds: The stock one from Makerfarm for 12V (PCB heatbed) with a glass bed on top and one 230V mains 500W silicone heater glued to a CNC milled ~5-8mm aluminium heatbevon mardy3d - General
What a great discussion! My dream configuration would be to have a removable layer as well. It supports modularity with respect to: (a) printing the next print quicker and (b) trying out new print surfaces. Though, I can see the issue of having an alu + glass combo because putting a piece of glass on top of an alu plate could possibly lower the advantage of the alu plate (even heat distrubution,von mardy3d - General
Thank you very much for the good help! In fact, I let the aluminium part be made on a CNC mashine. Quotethe_digital_dentist 500W is a good power level for about 300 x300 mm plate. My machine has a 450W heater and is about that size and gets up to 105C for printing ABS in about 5 minutes. I am assuming that you're using 220VAC as well then? Did you integrate any thermal fuse or something similarvon mardy3d - General
Hello fellows, I would like to implement a 3d printer setup with 5 to 8mm aluminium printbed and a silicone heater beneath it. It outputs 500W at 230V. My question is how to mount the whole construction properly? My ideas: Safety: Ground the aluminum as well as all metal parts of the printer. I am aware and capable of the safety issue. Thermal isolation: How should I do that? My current PCB bvon mardy3d - General
Good day everybody! I am planning to add a filament cooling feature to my printer. But instead of loading a fan on my hotend directly, I'd like to connect an air flow generating device to a flexible tube and lead it to my hotend. Of course, fans are the first idea to be used as the air flow generating devices. The biggest issue is now that the air is not really travelling through the tube. Whavon mardy3d - General
QuoteVDX ... normal habe ich die Temperatur über den Druck konstant gelassen -- ansonsten an den Temperaturwechselstellen Pausen einfügen, den Regler auf die neue Temperatur einpendeln, und weiterdrucken lassen ... Okay, das ist einleuchtend! QuoteWurstnase 350W bei 200x200. Wenn ich das Bild richtig verstehe, dann dauert es 1 Minute und 15 Sekunden, um von ~60°C auf 100°C aufzuheizen. Holla, davon mardy3d - Druck- und Heizbetten
Danke für eure zahlreichen Antworten! QuoteSteBa Wie kommst du überhaupt darauf dass dein MK2 240W bringt?? Die liegen im Normalfall +/- bei der Hälfte. Ich habe an meinem Heizbett 11V bei einem Widerstand von etwa 0.6 Ohm gemessen. Das ergibt etwa 200W. Bedenke, dass ich kein 200x200mm**2 sondern ein 254x254mm**2 Heizbett im Betrieb habe. QuoteVDX ... ich habe ein 12V-Silikon-Heizbett direkt avon mardy3d - Druck- und Heizbetten
Guten Abend an alle, Es steht ein weiterer Umbau an, der die Beheizung meiner Alu-Druck-Platte (8mm bzw. in Zukunft 5mm) betrifft. Meine bisherige Konfiguration: Prusa i3 Derivat mit RAMPS1.4 und Marlin. Dimensionen des Druckers: 25.4x25.4 cm**2. Reihenfolge der Druckplattform: y-Carriage -> Kork -> MK2-Heizbett -> 8mm Alu-Platte. Das MK2 Heizbett läuft, wie auch der Rest des Aufbaus,von mardy3d - Druck- und Heizbetten
Guten Sonntag an alle! Ich bin auf der Suche nach einer Möglichkeit Timelapse-Aufnahmen mit dem Raspberry Pi während des Druckens aufzunehmen. Dazu kommt noch die Anforderung, dass ein normaler Kamera-Server zum Beobachten zur Verfügung stehen soll. Natürlich kann man ein Skript einrichten, welches alle X Sekunden ein Bild über die Webcam aufnimmt (z.B. mit fswebcam oder dergleichen). Darüber hvon mardy3d - Allgemeines
Nur eine Idee: Warum nicht den Luftstrom wo anders erzeugen und mit Schläuchen an die passende Stelle geleiten? Ähnlich den CNC Späne-Pustern. Und die ganze Schlauch-Konstruktion per Magneten modular an- und abbaubar.von mardy3d - Allgemeines
Trivia: Nach obligatorischer Klausuren-Phase vor Weihnachten: I am back :-). Danke an alle für die große Beteiligung an der Diskussion! Das ist, wovon Open Source lebt :-). Fachliches: Ich werde die LIYCY2x0.25 und LIYCY4x0.5 für Sensoren und Motoren ausprobieren. Dazu werde ich 2x1.5mm**2 ohne - wenn eBay etwas schönes hergibt auch mit - Schirmung für das Heizbett nutzen. Mir sind noch zwei weivon mardy3d - Allgemeines
Danke dir für deine Antwort! Die Querschnitte werden nicht gleich bleiben, da ich nicht über die Hersteller-Kabel verfüge. Führen damit dann meine angestrebten Längen doch zu Problemen? Lasst mich meine Fragen weiter konkretisieren: Was sind kritische Längen (bzw. Längendifferenzen) Was sind Effekte, die Probleme bereiten können? Ein weiteres Mal vielen herzlichen Dank! :-)von mardy3d - Allgemeines
Hallihallöchen, Ich bin Besitzer eines i3 und möchte die Elektronik vom Rahmen in eine feine Holzbox verfrachten. Diese soll immernoch nah am Drucker stehen, allerdings sind viele Kabel zu kurz. SD/LCD Kabel werden nicht verlängert, da diese Einheit auf die Box kommt. Zu verlängernde Kabel sind also: x, y, 2*z, Extruder Stepper 2* Temperaturfühler Hotend-Lüfter Heatbed Versorgung Hotend Versorvon mardy3d - Allgemeines
Which code did you upload to your Arduino Uno?von mardy3d - General
Sehr interessant, danke für diese Informationen! D.h. Nenn- und erlaubte Betriebsspannung hängen nicht stark voneinander ab. Wozu eignet sich die Angabe der Nennspannung denn dann? Es wäre dann sinniger, Höchstdrehzahl pro Betriebsspannung anzugeben, liege ich da richtig? Ich vermute darüber hinaus, dass Haltemomente in irgendeiner Weise von Betriebsstrom und -spannung abhängen.von mardy3d - Elektrik & Elektronik
Guten Tag an alle RepRap'ler, Zur Zeit baue ich an einem Projekt, welches 3D gedruckte Teile nutzt und ebenso Stepper-Motoren via eines A4988 ansteuert. Über einen Arduino Uno zunächst. Mir ist nicht klar, wie streng die Spannungsangabe auf Stepper-Motoren einzuhalten ist. Vielleicht könnt ihr mir helfen. Das Projekt ist "yet another" Kuka-styled Roboter-Arm und es wird selbstverständlich open svon mardy3d - Elektrik & Elektronik
Good day everybody, For a long time already, I am thinking about electrifying a scooter. I know that it is not too much connected to 3D printing but since I love my printer and the community (you guys!), I am asking you. This is what I thought of: The model I thought of is such a device: scooter. Of course, this is still upgradable in means of stability and feasability for mounting a motor. Thvon mardy3d - Let's design something! (I've got an idea ...)
Quotestud54 Man kann z.B. kleine Blöcke aus hitzefestem Silikon gießen...so 30x30. Löch in der Mitte mit eingießen...fertig. Man kann leveln und verstellen tut sich dann nix mehr.... Sehr interessanter gedanke. Kannst du den noch weiter erläutern? Hast du da ggf. 'nen Bild von, ich kann mir das noch nicht ganz vorstellen.von mardy3d - Allgemeines
Hält das Filz die Temperatur langfristig aus? Oder nimmst du das als Verbrauchsmaterial in Kauf?von mardy3d - Allgemeines
Mir sind eben Topfreiniger-Schwämme hier über den Weg gelaufen. Zugeschnitten könnte es die Bürsten ersetzen? QuoteBurningman Das hier ist mein Abstreifer für eine Kossel Mini mit MK3 Heatbed. Was hast du dort für ein Material eingelassen?von mardy3d - Allgemeines
Auch ich habe mir einen solchen kleinen feinen Setup gebastelt. Dennoch kam ich ins Grübeln: Ist es nicht bedeutend sicherer bei längeren Drucks, wenn man direkt von der SD Karte druckt? Zugegebenermaßen kann man das in Octoprint so einstellen, dann gehen aber ein paar Funktionen verloren.von mardy3d - Allgemeines
For me - as layman at least -, this design looks pretty nice. Are there any videos or such which show a functional copy of it? I'd be interested in what one can do with it. :-)von mardy3d - Look what I made!
QuoteWurstnase Invertiere mal deine Max-Endstops. Die dürfen eben nicht auf triggered stehen! Niemals! Unfassbar! Der Puls rast und der Drops ist gelutscht :-) Nicht nur das _HOME_RETRACT_MM klappt tadelos, sondern auch das ABL funktioniert "like a charm"! Vielen Herzlichen Dank für Deine Hilfe!von mardy3d - Allgemeines