Hello, I'm using a Self created kossel with hexagon hotend and ramps. I've calibrated the extruder Steps correctly, and the prints are quite nice, BUT only the Second Layer isn't as nice as the other. There ins'zu enought filament oozing out of the nozzle. At the 3rd Layer, the Problems don't Show again. I adjust the manual z-high, and also Check all the other Parameter. Chould someone please hvon nimrod - Delta Machines
after all, the stutter-effect decreases after i changed the display. now there are only some little effects at the points the Motors turns direction (but noch everytime) could i solve this problem by increasing the current of the Stepper driver? or are there ather possibilitys?von nimrod - Delta Machines
I'm going to buy one, but for this project "Build a kossel without any Sets or kits" i prefered a simple Electronic. For the next Time, or the next Upgrade, a Duet Board Is in the top of my List.von nimrod - Delta Machines
So i try and disable the Full graphic and Order a new normal 2 Line lcd Display. Hopefull this will solve the Problem. Are there some other Ideas?von nimrod - Delta Machines
I have the Full graphics display Controller. My other kossel has a normal Lcd Display. Is it possible that this Is the Problem?von nimrod - Delta Machines
QuotePaul Wanamaker nimrod, EDIT: took out what I said as you had replied... How many steps per mm do you have now with 16 microsteps? What did you mean? I have 80 steps per mm with the 1/16er and 160 with the 1/32er. All Jumpers are enabled.von nimrod - Delta Machines
after i changed the stepper (now it works with the 1/16) and decrease the acceleration, the Problems are still there. it seems they are not only at the points where the motors change direction. but i dont know the reason... now i also changed the belts, the rods, but it isn't better than before. i can't imagine that this problem comes out of the 8bit arduino.von nimrod - Delta Machines
it sounds like it is better to replace the "better" drv8825 by the "old" 1/16er stepper. first i will decrease the acceleration from 3000 to 1500 and try. if this doesn't work, i will replace the stepper with the others.von nimrod - Delta Machines
i printed with SD Card. this is my second Kossel. the first, from t3p3 with arduino and Marlin works very smooth, and there aren't any Problems like this. the only differents between both printers are the Motors (the "old" have a higher Torque), the heated bed and the stepper driver ("old" 1/16 vs "new" 1/32) also the firmware and the igus gliders are the same.von nimrod - Delta Machines
A few days ago, i finished my new delta printer, a kossel mini. I get all the things i Need for my own and all printed Parts are printed by my self. The kossel works quite well, but there also some problems: if i move the axis manualy with pronterface or via display, they Movie quite smooth, but if i Print Sommerhoff, the Motors See stuttering. The vref of the Stepper driver Is about 0,85 and tvon nimrod - Delta Machines
danke für den Link Manu, genau nach dieser Anleitung bin ich nun schon mehrfach vorgegangen, leider ohne erfolg. verwunderlich ist zudem, das beim manuellen Abfahren der Wege wie gesagt keine Unebenheiten zu erkennen sind. die Spitze des Hotends hat überall den selben Abstand. sobald ich jedoch drucken will, verfährt er so schräg.von nimrod - Allgemeines
hallo liebe Community, ich habe hier schonmal ein Thema gestartet, und möchte nun versuchen mein Problem noch einmal etwas genauer zu schildern, um vllt eine Lösung zu erhalten. ich habe einen Kossel Mini von t3p3 gebraucht gekauft. leider habe ich immer wieder an der ein oder anderen Stelle ein Problem. obwohl die Drucke in der Regel sehr sauber werden, und die Qualität sehr überzeugt, habe icvon nimrod - Allgemeines
ich nutze Marlin. habe neben dem Phänomen auch festgestellt, das der erste Layer am vorderen rechten turm, dem y-Turm etwas "flacher" ist als auf dem restlichen druckbett.von nimrod - Allgemeines
Guten Abend liebe Gemeinde, ich habe diesen Thread nun ein paar mal durchgelesen, und hoffe das ihr mir bei meinem Problem helfen könnt. Bezüglich der maßhaltigkeit und der Genauigkeit habe ich an meinem Kossel mini keine Probleme und bin sehr zufrieden, allerdings habe ich nun herausgefunden, das das hotend, wenn es mittig runter fährt so über dem druckbett steht das noch ein Blatt Papier durchnvon nimrod - Allgemeines
Quotedc42 you should use auto delta calibration instead.. can you help me with this? i don't kow exactly what you meanvon nimrod - Delta Machines
hallo ihr lieben, ich bin neu hier und habe vor gut 10 Tagen einen gebrauchten Kossel mini von t3dp3d gekauft. dieser funktionierte nach der Kalibrierung wunderbar, und ich war mit dem Druckergebnis sehr zufrieden sodass ich mich an das erste Mammutprojekt rantraute und begann, die 3D Catan Felder eines nach dem anderen auszudrucken. ich drucke mit Cura und habe die Autolevel Prozedur entsprechevon nimrod - Allgemeines
hello, my name is Björn and a few days before, i bought a Kossel Mini (t3dp3d). that one was used and still working very fine. after the kalibration i began to print ant all worked very well for a few days, then i decided to print some larger Project, and start up with some tiles of the 3D Catan (http://www.thingiverse.com/thing:26979/#files) after 6 Tiles, suddenly the Autolevel seems to be incvon nimrod - Delta Machines