Zeige alle Beiträge eines Teilnehmers
Alle 3D-Drucker-Themen die in kein anderes Forum passen können hier rein. Anfänger die sich nicht sicher sind wo ihre Frage am besten hinpasst, können sie gerne hier los werden.
Re: Re-access Wiki - 2 Monate zuvor
... hmmm ... there is a "User::Leadinglights" with last action date from 2017 ... but not much morevon VDX - Administration, Announcements, Policy
Re: IGUS rod end vs IGUS ball and cup joint - 2 Monate zuvor
... the "double ball joints" were my solution for a "stick'n'slip" problem when using it for etreme fine positionig -- if you look into my images, every joint consists of 2 ball magnets, rolling on each other, so no gliding and no stick'n'slip (was meant for micro-positioning with a working range of below 50mm square and step resolutions near to single microns). But then too, the "joint" is notvon VDX - Delta Machines
Re: IGUS rod end vs IGUS ball and cup joint - 2 Monate zuvor
... with the double-ball joints you''ll have a "nonsingular" joint, so the kinematics are more complex ... but with only one magnetic ball, an iron-counterpart and a PTFE-ring to give some microns distance, it's the same, as with the ball'n'cup jointsvon VDX - Delta Machines
Re: IGUS rod end vs IGUS ball and cup joint - 2 Monate zuvor
... my first delta-demonstrator from 2007 (then named "tripod") too was built with double magnetic ball joints. Attached some images of the hinges and the completed setup ...von VDX - Delta Machines
Re: thermistor calibration - 3 Monate zuvor
... there are differen thermistor tables for specific sensors - to "calibrate" another sensor you have to measure the values at the specific temps an generate a new table ...von VDX - General
Re: configuration.h for a fast CoreXY? - 3 Monate zuvor
... the max. speed depends on the Controller you have ... an Arduino Mega 2560 lacks pretty much, compared to a Due or even faster one ...von VDX - Firmware - Marlin
Re: Problem zwischen Schicht 1 und Schicht 4. Die Z-Achse bewegt sich nicht - 3 Monate zuvor
... solltest du hier keine Antwort bekommen -- es gibt auch ein deutsches Forum:von VDX - Firmware - Marlin
Re: Testing boards and step motors/ Error - 3 Monate zuvor
... could be, the endstops (or only one) aren't configured properly, so the homing didn't work ...von VDX - Reprappers
Re: Testing boards and step motors/ Error - 3 Monate zuvor
... check for polarity and switching state of the homing switches with "M119". If they seems correct, then try to home them separate with "G28 X" and "...Y", "...Z" respective. If your startup sequence "automatically" performs G28, then remove this line ...von VDX - Reprappers
Re: An Optical Filament Sensor That Actually Works - 3 Monate zuvor
... as three of his 4 posts were "injected" with spam and there wasn't much help from the rest, I've deleted his account - there are more spammers recently again, so better remove them by sightvon VDX - Tech-Talk
Re: email strangeness - 3 Monate zuvor
Hi Mike, ... PM me your correct email, then I'll change it ...von VDX - Administration, Announcements, Policy
Re: Marlin: different E_factors in multi_nozzle_duplication issue - 4 Monate zuvor
... best bet could be a divider (or multiplicator) to get different step counts for the two extruders. This could be done with a separate Arduino or ESP32, if the factor isn't achievable with a simple counter IC.von VDX - Printing
Re: Excited to Start My 3D Printing Journey - Seeking Guidance for a Newbie - 4 Monate zuvor
Hello Marcos, depending on your needs there are many different sub-forums like for firmware, electronics, mechanics, PC-software and many more. One essential hint - when searching through the forums, then change the searcch date range in the bottom of the mask from "Last 30 days" to "All dates", or you won't find anything usefull ... most interesting infos are much, much oldervon VDX - General
Re: TX/RX on J19 socket - 4 Monate zuvor
AFAIK, this is a RaspberryPi header - so look into related infosvon VDX - Firmware - Marlin
Re: Biete 2 teildefekte FDM-3D-Drucker als "Bastel-Material" oder Umbau/Reparatur an - 4 Monate zuvor
... die beiden Drucker sind "reserviert" - also aktuell nicht mehr verfügbar ...von VDX - Schwarzes Brett
Biete 2 teildefekte FDM-3D-Drucker als "Bastel-Material" oder Umbau/Reparatur an -[ERLEDIGT] - 4 Monate zuvor
Hallo, ... wer Material oder eine Basis für einen Neuaufbau sucht - ich habe einen älteren Eigenbau-ORCA und einen "Wanhao Duplicator Plus MarkII" über, die ich günstig abgeben kann (für Porto + etwas als "Motivationsaufschlag"). Beim ORCA ist mir heute beim Drucken die Düse ins Bett gerauscht und hat die Bett-Lagerung ausgehebelt/dejustiert, was eine Zerlegung und Neueinrichtung bräuchte - sonvon VDX - Schwarzes Brett
Re: Bouis Sparkcube 1.1XL - 4 Monate zuvor
... geht mir manchmal mit meinen Posts von 2007 und etwas später auch sovon VDX - Allgemeines
Re: Different step per z axis - 5 Monate zuvor
... could be better, when using a bigger/stronger single motor to drive three identical spindles? - then all hassles will vanisch instantlyvon VDX - Firmware - Marlin
Re: PSA bad endstops! - 5 Monate zuvor
... if thinking about resoldering - cut the legs of the switch at the "knee", then reverse it and fix the cuts by soldering ... schould be mechanically sturdy enough to work as meant to ...von VDX - General
Re: PSA bad endstops! - 5 Monate zuvor
... with this JST-connectors it's not really a problem to rearrange the wires (by releasing the nose with a needle and extract and reinsert the wires) - had to do this with a bunch of 20x connectors, when one of our suppliers "mirrored" an order of our PCB's for a sensor, we manufactured then for Siemens ... and they (Siemens) were in urgent need for a small series, before the "correct" PCB's couvon VDX - General
Re: [moved here] - some ideas about micro/nano-fabrication and such ... - 5 Monate zuvor
... it's not really meant for Joe average -- more for interested individuals or R&D groups ... either comercial or DIY/OSHWvon VDX - Tech-Talk
Re: [moved here] - some ideas about micro/nano-fabrication and such ... - 5 Monate zuvor
... and for "micro/nano-positioning" -- if you look in my first attached image - on the left, above "Positionierer" - this is a 3-axis nano-positioner, assembled from 3 "Piezolegs"-drives. This setup has a moving/positioning range of 23x23x23mm in XYZ with an overall accuracy of 150 nanometer per "step" or, when in "clamped" mode, even down to sub-nanometer resolution ... what it lacks in this vvon VDX - Tech-Talk
Re: [moved here] - some ideas about micro/nano-fabrication and such ... - 5 Monate zuvor
... by the way - with the galvanic approach you can easy manufacture any size and form of tips and probe-points, which you can get as "hollow form" in a plastic sheet. This would be a perfect use for the UV-LCD-3D-printers with roughly 25 microns big "voxels". With some tweaking you can get even finer resolution, if you modify a common data-beamer with an UV-LED as light source and adding a redvon VDX - Tech-Talk
Re: [moved here] - some ideas about micro/nano-fabrication and such ... - 5 Monate zuvor
... I had a cooperation (more I had to help them solve some handling issues), from where I've got a bunch of "nano-nailheads" -- it's essentially a halfsphere of gold or platinum with 30µm diameter with a 30 or 50µm long "nano-needle" centered at the flat side. This nano-needles were around 100 nanometers at the center-point connection and some nanometers at the tip - they were made galvanicallyvon VDX - Tech-Talk
Re: WIKI Clean up - 5 Monate zuvor
... from 1999 to 2006 I was busy with R&D for micro/nano-tech and too handling them (microscopy, micro/nano-positioning, micro-assembly, ...). If you'll need some help here -- have some of the parts and more in my basement (microscopes, grippers/tweezers, micro-positioning stages, ...) Here some related images:von VDX - Tech-Talk
Re: WIKI Clean up - 5 Monate zuvor
... with the "laser-thermo-transfer" some nanometer thick layers can be "sprayed" or more like "PVD" coated (as in Physical Vapor Deposition) - the lower limit are actually the spot sizes of down to 50 microns with laser diodes or down to 10 microns with fiber-lasers and such (have some UV-DPSS and actually an "green" picosecond laser for testing until end of May). What would help with finer latvon VDX - Tech-Talk