QuoteThePaddington Ist Silberstahl das Hauptkriterium? Sonst vllt hier in Cf53: https://www.dold-mechatronik.de/Praezisionswelle-8mm-h6-geschliffen-und-gehaertet-ZUSCHNITT-bis-1200mm-1300-EUR-m-025-EUR-pro-Schnitt In dem Fall ja, da ich durch die Wellen durch bohren muss. Bei gehärtetem Stahl könnte das ohne entsprechendes Equipment (das ich nicht habe) sehr tricky werdenvon Royce - Mechanik
Guten Abend mitnand, ich source momentan Teile für das wundervolle Projekt Tantillus Reborn von Lars. Leider stecke ich bei der Suche nach 8mm Silberstahlwellen (Passung h6, präzisionsgeschliffen, 1.2210) in 220mm Länge fest. Ich finde einige Angebote als Meterware, mir fehlt aber leider die Möglichkeit die Wellen auf die korrekte Länge zu bringen. Wüsste da jemand eine Quelle? Die gängigen (Mävon Royce - Mechanik
Hi Comm, recently, I have issues with my G28 Homing. Setup: P3Steel Frame Arduino / Ramps combi TMC2130 on X, Y, Z and E via SPI Marlin 1.1.8 Pressing "Home" in Octoprint moves the bed / printhead about acm to the right and 1 cm to the front (opposite direction of the homing direction). Using the Display constrol buttons, it does the same but additionally rapidly moves to the right and front anvon Royce - Firmware - Marlin
Hallo zusammen, Kann acceleration / jerk die Größe des gedruckten Objekts beeinflussen? Ich habe heute einige Probedrucke mit einem Ripple-Testcube gemacht. Dabei habe ich Acceleration und Jerk sowohl hoch als auch runter gestellt. Bei erhöhter Acceleration wird der Würfel ganze 2 mm höher als mit meinen Werten, bei verringerter Acceleration verhält es sich andersrum. An den Steps habe ich nichtvon Royce - Elektrik & Elektronik
Hi folks, Quick question: Can acceleration affect the printed objects size? I fiddled around with a ripple-test-cube and adjusted the acceleration and jerk settings. When I set acceleration to Marlins defaults (3000 instead of 1500 before), the cube became 22mm tall instead of 20mm Also I played with the feedrate (500 instead of 300 before). While being on topic: What are your used values forvon Royce - RAMPS Electronics
Hi again When scrolling through the configuration.h, I found the clean nozzle feature. What surface (like a sponge, wire brush, ...) would be recommended for this? Thanks!von Royce - Firmware - Marlin
Hi folks, I finally made it to finish my Prusa style Toolson MK2 printer. Now I'm facing the following "challenge": The bed has a size of 220 x 220 mm. On top I attached a PrintBite plate with 200 x 200 dimensions. Now, I need the front left corner of the PrintBite to be 0/0, therefore the center should be 100/100. At the moment, the prints get printed slightly off center, they should of coursevon Royce - Firmware - Marlin
Hallo zusammen! Ich habe nach langem Machen und Tun endlich meinen Drucker fertig gebaut, es ist ein Toolson MK2 geworden. Nun stehe ich vor folgender Herausforderung: Das Bett selbst hat Abmaße von 220 x 220 mm. Darauf habe ich eine PrintBite Druckplatte, die 200 x 200 mm misst. Nun möchte ich, dass die Koordinaten 0/0 als die linke vordere Ecke des PrintBites erkannt wird, demnach natürlichvon Royce - Software
Wouldnt this make jumpers useless?von Royce - RAMPS Electronics
Update: Ich habe gerade mal die Jumper pins unter dem Stepper Driver auf Durchgang gemessen. Mein Multimeter piept mich an wenn ich die Jumperpärchen messe. Sollten diese Jumper pins nicht eigentlich open circuit sein?von Royce - Elektrik & Elektronik
Dust, I just measured the jumpers underneath the driver sockets. They seem to be connected without the jumpers installed. Unfortunately I don't have a spare Ramps by hand to check it on a spare one. Continuity check with a Multimeter gives a beep. I guess this causes the issue?von Royce - RAMPS Electronics
That's a good idea! I will check that in a few hours after work Ramps is a good board for a good price, but it's annoying that there is nothing like a quality control instance or such. It's already the 3rd Ramps I bought, every board had an issue in some way.von Royce - RAMPS Electronics
I wired the steppers as explained in various tutorials. Soldered in the pins and bridged CFG1 to GND with a small piece of wire. Jumpers underneath the stepper driver were removed. Pics are attachedvon Royce - RAMPS Electronics
Jau. ich habe jeden Treiber (einzeln) auf jedem Sockel getestet. Das Problem tritt jedes mal aufvon Royce - Elektrik & Elektronik
That was the first thing I triple-checked. The orientation is correctvon Royce - RAMPS Electronics
Klingt schwer danach ja. Falschrum eingesetzt schließe ich mal aus, das habe ich mehrfach gechecktvon Royce - Elektrik & Elektronik
Guten Abend zusammen, ich bin gerade dabei mein Ramps mit TMC2100 (5V Version von Watterott) upzugraden. Ich habe die Brücke von CFG1 nach GND gelötet und unter den Stepper Driver Sockeln alle Jumper entfernt (wie hier empfohlen: ). Sobald ich nun den ersten Driver einstecke (Egal ob X, Y, Z oder E) gibt es einen Disconnect und das Arduino schaltet sich ab. Hat hier jemand eine Idee? Danke voravon Royce - RAMPS Electronics
Guten Abend zusammen, ich bin gerade dabei mein Ramps mit TMC2100 (5V Version von Watterott) upzugraden. Ich habe die Brücke von CFG1 nach GND gelötet und unter den Stepper Driver Sockeln alle Jumper entfernt (wie hier empfohlen: ). Sobald ich nun den ersten Driver einstecke (Egal ob X, Y, Z oder E) gibt es einen Disconnect und das Arduino schaltet sich ab. Hat hier jemand eine Idee? Danke voravon Royce - Elektrik & Elektronik
Sorry für die späte Antwort, ich hatte bisher keine Zeit mich weiter mit dem Thema zu beschäftigen. Vielen Dank für eure Hilfe, ich nutze den freien Tag um etwas weiter zu bastelnvon Royce - Elektrik & Elektronik
Hallo zusammen, ich bin gerade dabei mein Ramps mit TMC2100 Drivern etwas aufzupeppen. Nun lese ich verschiedene Dinge über die Installation, die irgendwie nicht ganz zusammenpassen. Laufen soll das Ganze im Spreadcycle mode mit Interpolation auf 1/256 Stepping. Das eine Tutorial sagt: Alle Jumper vom Ramps (unter dem Driver) entfernen, passt. Das nächste sagt: Alle Jumper drauf und CFG1 auf GNvon Royce - Elektrik & Elektronik
Hi folks, I activated #define MANUAL_BED_LEVELING in configuration.h. As soon as I start "level" bed from the prepare menu, after homing xyz, the nozzle goes to point 1. So far so good. On point 1, the nozzle is outside the bed area (on the X and Y axis). same goes for point 2, 3 and so on. Is there anything I'm missing? Thanks in advancevon Royce - Printing
Good evening, I upgraded to RAMPS 1.4 today. I noticed that the print cooler (connected to D9 / extruder 2) is always running. It runs at the same speed, no matter what I set in S3D. In Marlin I set #define MOTHERBOARD BOARD_RAMPS_14_EFB so it should be able to control the hotend, fan and bed. Measured with a voltmeter, it gives me a reading of 5.9V on D9 constantly. Any ideas? Thanks in advanvon Royce - RAMPS Electronics
Thanks dust, didnt knew that. So you think it's better to run the printer without a Display at all?von Royce - RAMPS Electronics
Thank you for that good information, dc42. Unfortunately I don't understand this article 100%. The voltage regulator WILL overheat when a graphics display is connected and no 5V via USB is provided? (see " if you power a servo or a graphic LCD from the RAMPS, then you will almost certainly overheat the voltage regulator. The usual symptom is that the system will not work unless it is connected tvon Royce - RAMPS Electronics
Yes, it's on the mega. Damn, that doesnt sound good. So I'll probably need a new mega, right?von Royce - RAMPS Electronics
Hi folks, I'm pretty new to the RAMPS topics, so please forgive my newbieness in some points I hooked up my RAMPS shield to an Arduino Mega, powered it via USB and flashed the latest Marlin firmware (no settings made yet). Additionally I connected a mechanical entstop (X_MIN) and the full graphics LCD. As soon as I connect both +/- connectors (the green ones on the shield) to a 12V power supvon Royce - RAMPS Electronics