Line Infill, Solid Surface runter auf 3, Perimeter Flow Rate auf 1, Extra Shells auf 0, Infill Perimeter Overlap auf 0.2, Infill auf 0.3 erhöht. Ich glaube, das wars.von Arakon - Allgemeines
Das sieht schon mal massiv besser aus.von Arakon - Allgemeines
Danke für die Tipps, ich probier mal durch. 0,0 ist beim Mendel90 normal.von Arakon - Allgemeines
Ich hab die Files mal angehängt. Overlap ist bei 0.2.von Arakon - Allgemeines
0.4mm, das Standardteil vom Mendel90. Layer Height ist bei 0.2, Edge width over height bei 2.05.von Arakon - Allgemeines
Yep, wurde genau abgemessen.von Arakon - Allgemeines
Beim slicing habe ich die abgebildeten Löcher zum Aussenrand und ganz massiv um runde Löcher herum. Die sind auch sichtbar, wenn ich das gcode File in Pronterface lade. Mit welcher Einstellung kann ich das beeinflussen? Layerverbindung in der Vertikalen ist sehr gut und ohne Lücken. Mit anderen Slicern hab ich bisher wenig Glück gehabt, die Ergebnisse waren immer schlechter als mit Skeinforge undvon Arakon - Allgemeines
Alles klar, danke. Hab mir mal eine Pappkiste bestellt (die Umzugskartons im örtlichen Baumarkt waren allesamt viel zu klein) und probier es damit. Lüfter ist aus im ABS Profil.von Arakon - Allgemeines
Moin. Ich hab einen Mendel90.. bisher nur PLA gedruckt, und ein Mal mit einer halbmeter Probe ABS versucht, das sah auch gut aus, hat sich aber nach oben hin leicht aufgelöst. Reicht es, um Zugluft-Schutz und höhere Umgebungstemperatur zu erreichen, einfach einen 50x50x50 Versandkarton über den Drucker zu stülpen? Würde das irgendwann mal in "schön" nachbauen aus Holz, aber vorerst wäre der Kartovon Arakon - Allgemeines
Klasse, vielen Dank.von Arakon - Kommerzielle Angebote & Produktvorstellungen
Super, danke.. Allerdings meldet der Shop dann 4.99 Versandkosten, soll das so?von Arakon - Kommerzielle Angebote & Produktvorstellungen
Abs und PLA, Farbe ist erstmal egal. Ich will demnächst eine Rolle Abs und recht bald dann auch nochmal PLA bestellen, und suche dafür einen Shop.von Arakon - Kommerzielle Angebote & Produktvorstellungen
Irgendwie finde ich im Shop die erwähnten Probepackungen nicht?von Arakon - Kommerzielle Angebote & Produktvorstellungen
I'm quite happy with the print quality now. Only one issue seems to remain.. This was printed with 0.1mm layer height, nice and smooth, except it left a blob at the spot where the print finished. I am using your end code and skeinforge.I didn't notice this issue with prints that end in a flat surface, and less with bumpy surfaces, but I still usually get a fine "hair" pulled up by the extruder.von Arakon - Mendel90
Gibt es Pläne, Neonfarben anzubieten? Es ist irgendwie sehr schwer, z.b. neongelbes Filament zu finden.von Arakon - Kommerzielle Angebote & Produktvorstellungen
Thanks, but they're all firm and the pointers seem to stay in the same direction too. I wonder if something went out of whack because I turned the printer sideways and back again.. currently it seems to print fine again with the same settings. I installed some LED strips, directly to the 12V line of the power supply. They flicker while printing.. does the Melzi board (or the motors for that mattevon Arakon - Mendel90
I hadn't changed anything about the slicer settings (Skeinforge) between the print last night and the one this morning. They were actually both generated back to back last night.von Arakon - Mendel90
Gnah.. I don't get it. I had adjusted the Z_Home_Pos to where it printed a 0.23 mm skirt all around when printing 0.2mm layers. Today I start a print, and the skirt is perfectly even.. except it's now 0.3mm thick and the first layer has visible lines. If something had shifted, i.e. one screw or one motor slipped, I wouldn't still get a perfectly even skirt.von Arakon - Mendel90
That was done with Craftware. I tried Skeinforge just now. Same STL. A lot less issues.. but I'm running into trouble using skeinforge with anything that needs support. Last thing I printed with support was unusable due to the support being merged so firmly with the part, that it wouldn't come off without major destruction. Edit: Nevermind, just found some info on supports, will give it a spin. Avon Arakon - Mendel90
That was probably the problem then.. thanks for the help so far. New print.. first layer seems much better now. This was done at 190°. However, there's still some strangeness. The bottom part has a small gap between the walls that make up the sides. Also, halfway up, I get lots of thin threads hanging around (only along the short sides) and in one corner it looks like the filament was ripped ouvon Arakon - Mendel90
The hobbed bolt is clean and not slipping. I had tightened the nuts with the star washer, but after it came off twice, I used loctite. Just a drop, it can easily be undone using a wrench for the nut.von Arakon - Mendel90
The E-steps are fine, it actually extrudes 100mm when I tell it to. What I wasn't aware of is that z_home may have values of 2 digits after the period, I believe I can home it in even closer this way. I started a print earlier and hope this comes out better, I increased the temperature by 5 degrees. Everything is attached firmly now, although it did drop the big M8 nuts during the TARDIS print.von Arakon - Mendel90
Got it calibrated further with a dial gauge, thanks. I switched to a different filament now (3mm blue PLA by Trijexx). Using the same settings as before (with adjustments for the filament thickness of course), I now get okay prints with it, but still some issues. The first image shows bumps in the first layer that randomly follow the outline. The same occured with an ABS sample I tried. The nextvon Arakon - Mendel90
Update on this.. new Z-height and sliced with skeinforge and nophead's settings greatly improved it, but there's still some oddness.. especially the stray threads of PLA on the new print, and still some partial shininess.. what causes that?von Arakon - Mendel90
1) I had only tried higher to see if that would help, actually. 3) Did that, I get an average of 0.28mm now after another adjustment. Is that good enough? I'm not sure I can actually adjust it any finer in the firmware? 4) I use brake cleaner.. that gets rid of any trace of grease or anything. I'm currently doing another print after an email from nophead with adjusted settings and using skeinforgvon Arakon - Mendel90
Quotefloville QuoteArakon Da ich das Ding nach Anleitung gebaut habe und zu dem Zeitpunkt noch alles vollkommen lose und kreuz und quer lag, war das naheliegend, aber definitiv nicht praktisch. Hier sieht man übrigens das erwähnte Eiern des rechten Gewindestabs: Die Gewindestangen sind mechanisch von der Z-Achse entkoppelt, leichtes eiern ist beim Mendel90 also irrelevant für das Druckergebnis.von Arakon - Allgemeines
I recently finished my Mendel90. I just printed one of the basic test objects, sliced with Cura and printed from SD. Same issues remain if sliced with slic3r or simplify3d Can anyone tell me what settings affect the issues in the pictures? Half shiny, half not, messed up head section, loose threads.. The biggest one is the bottom, the lines are round and not connected, and there's hardly any adhevon Arakon - Mendel90
Dann zerleg ich das mal bei Gelegenheit und schau, ob ich das begradigen kann, danke. Momentan zieht er so Fäden und das große Zahnrad hat ein paar "Wellen" drauf.. woran kann das liegen?von Arakon - Allgemeines
Und noch eine Frage.. beim PLA drucken wird gelegentlich die Outline mit hochgezogen oder pappt am ersten Layer des eigentlichen Bauteils. Ist der Extruder zu nahe am Bett?von Arakon - Allgemeines