QuoteRRuser Hovering over the Flag, and then hovering over the Thread Title, shows the same link, which is to go to the first post of the first page. There should be a ",gotonewpost" at the end of the link when hovering over the red flag. This is what does the MAGIC!von rhmorrison - Administration, Announcements, Policy
What browser are you using?von rhmorrison - Administration, Announcements, Policy
von rhmorrison - Administration, Announcements, Policy
No, just good business sense - get the customer to come back over and over and over again!von rhmorrison - Look what I made!
Depends on your filament supplier! You have to know the width of the filament when you slice your object. If you buy another roll of filament and it's width is different it will print differently unless you reslice the object. For example, recently I printed out an object with a filament width of 2.8 mm. It didn't come out as well as expected. I measured the filament and it was 2.6 mm (for a rolvon rhmorrison - Slic3r
If you will only be printing from an SD card and you can save to the SD card using Slic3r then NO, you do NOT NEED a HOST software.von rhmorrison - Slic3r
QuoteSlic3r 1.2.9 stable is out! It includes real-time incremental slicing, 3D preview, toolpaths preview, 3D honeycomb, customizable bed shape, integration with OctoPrint, pressure regulation and much more!von rhmorrison - Experimental
I suspect that you have Splodge activated. If so, deactivate it. If the Oozebane plugin is activated I would also deactivate it. Then activate the Skirt plugin.von rhmorrison - Skeinforge
WTF is "anchor code"? Please post the first 20 lines of a gcode file created with your settings. Are you sure you are looking in the proper location for the start.gcode file?von rhmorrison - Skeinforge
What is it that you want to accomplish?von rhmorrison - Skeinforge
Du muss es in der slicer ändern aber du kannst im fast jeden FW ein maximal geschwindlichkeit bestimmen. Am besten Probiere es aus mit deine Host software (z.B. im Pronterface kann mann XY, Z und extrude geschwindlichkeit angeben). Wert auf 1 (2, 5, 10) mm/m probieren zum feststellen mit welche geschwindlichkeit es bei dir zuverlässig läuft.von rhmorrison - Elektrik & Elektronik
Ich werde runter gehen mit der Temperatur and infill von 20% versuchen.von rhmorrison - Allgemeines
Beim Z ist deine geschwindlichtkeit wahrscheinlich viel zu hoch.von rhmorrison - Elektrik & Elektronik
Quotenophead It looks like you have your firmware E_STEPS_PER_MM set up for the old system where it was mm of extruded filament. It should be for mm of filament pulled into the extruder, which is about 36 times bigger. You can see the E values from Slic3r are increasing by small amounts, whereas the Repsnapper E values change by the same amount as XY. THEN change your E_STEPS_PER_MM to the propvon rhmorrison - Slic3r
Es gibt noch verbeserungs Möglichkeiten!von rhmorrison - Elektrik & Elektronik
In seiner Fall Methode 3. QuoteMethod 3 - Manually measured Resistance / Temperature datavon rhmorrison - Elektrik & Elektronik
Some oldies but goodies: Thermistor More accurate thermistor tables Measuring temperature the easy way Du hast nicht geschrieben welche firmware du nutzt!von rhmorrison - Elektrik & Elektronik
Mit 2015.03 der STL ist genau 30,00 mm von fläche bis zum fläche gegen über. Gemessen mit netfabb Basic.von rhmorrison - Software
Two at least - one per post!von rhmorrison - OpenSCAD
Please use "Attach a file" instead of posting thousands of lines of code!von rhmorrison - Delta Machines
Spiral Lightbulb Sculpturevon rhmorrison - Competitions
Oops... You did write that all you had was the HOLE DIAMETER and the WALL THICKNESS so: hD = 10; // Diameter of Hole tH = 20; // Height of the Triangle wT = 2; // Wall Thickness difference() { cylinder(r=hD+2*wT, h=tH, center=true, $fn=3); cylinder(r=hD/2, h=tH+1, center=true, $fn=100); } Now - Q.E.D.!von rhmorrison - OpenSCAD
If you take a look at the following pages: Solver Calculate side length of equilateral triangle inscribed in the circle SOLUTION: If a circle is inscribed in an equilateral triangle of side 2v3 units, then radius of the circle is Inscribed kissing circles in an equilateral triangle If you work out the math for your special case it turns out that the radius of a circle r that touches thevon rhmorrison - OpenSCAD
What do you need to do with an equilateral triangle that can NOT be accomplished by using $fn=3 and circle/cylinder function? What are you trying to do?von rhmorrison - OpenSCAD
QuoteAlterBastler@Harry2006 in configuration.h, Zeile 1533 #define NUM_MOTOR_DRIVERS 0 scheint bei Dir zu fehlen. Die Version 0.92 wurde zuletzt vor 18 Stunden geändert, man sollte nicht immer unbedingt die letzte Version benutzen.von rhmorrison - Projekte
QuoteHarry2006 Danke für den Hinweis, nur wie finde ich die Zeile 1533?? Bei mir stehen in der configuration.h keine Zeilennummern....zählen... bin wie gesagt Neuling bitte nicht mit Steinen werfen. Oder nutzte ein mächitge Open Source Editor z.B. Notepad++.von rhmorrison - Projekte
Also nicht der Motortreiber SilentStepStick - TMC2100 (Interpolation von bis zu 256 Mikroschritte) vergessen!von rhmorrison - Allgemeines