Show all posts by user
Printing issues ...
Page 1 of 1 Pages: 1
Results 1 — 8 of 8
I dont know if this is different, but I selected extruder 1 first then the M503 command.
Active Extruder: 0
Active Extruder: 1
Steps per unit:
M92 X80.00 Y80.00 Z533.00 E500.00
Maximum feedrates (mm/s):
M203 X300.00 Y300.00 Z5.00 E25.00
Maximum Acceleration (mm/s2):
M201 X3000 Y3000 Z100 E10000
Accelerations: P=printing, R=retract and T=travel
M204 P3000.00 R3000.00 T3000.00
Advanced variables:
by
Ray_
-
Prusa i3 and variants
Yes its Set to 2
It must be defined it shows up in the LCD Menu's
and heats and everything.
I have to assume at this point the board is bad.
I bought 1(this one) and could not get the X endstop to work.
So I requested to send it back and I bought a second one of the same board.
That one came and the X endstop worked fine. That 2nd board is the one that the E1 motor wouldn't work on no matter w
by
Ray_
-
Prusa i3 and variants
I checked and changed the #define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} to {80,80,4000,500,500}
Its ignoring the 5th as best as I can tell.
heres the M503 Response. (I don't know what half or more of it means)
Steps per unit:
M92 X80.00 Y80.00 Z533.00 E500.00
Maximum feedrates (mm/s):
M203 X300.00 Y300.00 Z5.00 E25.00
Maximum Acceleration (mm/s2):
M201 X3000 Y3000 Z100 E10000
Accele
by
Ray_
-
Prusa i3 and variants
Thanks Dust, I have an MKS Base board without Pololu's.
But I;m going to visually inspect each driver and look for missing or added parts on each section.
by
Ray_
-
Prusa i3 and variants
This turned out to be the Control board..that channel must be blown.
I put a second board in and both extruders work now..but the E1 extruder runs about 10 times faster than the E0 extruder. I switched the motor wires between both extruder motors (power off of course)
and the other motor then goes twice as fast.
I can not find anything in my configuration.h that would allow me to change speed's
by
Ray_
-
Prusa i3 and variants
I have a Hictop Prusa I3 printer, I put together and did a print or two on...but the bed isn't level enough for it to print completely.
Trying to level it was a nightmare, so I bought a Geeetech Dual extruder and an Inductive probe and a new control board (could'nt find anything about the original board and didn't want to damage it by trying to upgrade it's firmware).
I hooked everything up,
by
Ray_
-
Prusa i3 and variants
I am trying to set this up. I have a Prusa I3 printer and changed to a OSOYOO MKS Base V1.4 3D Printer Controller remix Board.
I got an Inductive Sensor (LJ18A3-8-Z/BX 8mm Approach Sensor Inductive Proximity NPN NO Switch DC 6-36V)
I connected it to the 12V supply and put a resistive divider on the output to neg supply.
I measure the output after dividing it and it (not connected to board) reads
by
Ray_
-
Printing
NEVERMIND I have this working.
I have put together my Hictop Prusa I3, and have been trying to replace the board with an
MKS Base 1.4 board and I can not get X Endstop to work. After going thru the Configuration 100 times I figured it had to be the replacement board.
So I got and RMA, and ordered the same board again so I didn't have to wait for them to receive it and give credit etc.
The new
by
Ray_
-
Reprappers