Show all posts by user

Re: Bed.g file - 4 years ago

I was asking myself a very similar question, so i tought why not just ask here. Is there any reason not to use M500 at the end of my bed.g? Nobody is recommending this, but don't i need to save my probed points into my config-override.g? Hope thtats the right place to ask.

by snakergy - Ormerod

Re: print quality awfull out of the blue - 5 years ago

Ok so month later i have finally fixed my problems! to make it short changing to the prusa slicer instead of cura and fixing a lot on my hotend did the Job. I have wrtitten a more detailled conclusion in the Duet Forum for those who are interessted. Thank you alot for your help! Stay healthy Snakergy

by snakergy - Printing

Re: Druckqualität plötzlich nicht nachvollziehbar schlecht - 5 years ago

Also nach Monaten harter arbeit habe ich endlich was erreichen können! @Siggi_Green ja mitunter hat das Hotend hat von allen Seiten Probleme gemacht (Lüftung, PTFE, Thermoelement), viele Dank! Ich habe im Duet Forum eine ausführliche Beschreibung meiner Probleme und den entsprechenden Lösungen geschrieben (auf englisch). Extrem kurz zusammengefasst hat ein Wechsel auf den prusa Slicer und eini

by snakergy - Allgemeines

Re: print quality awfull out of the blue - 5 years ago

Quotejefbed What kind of hot end does this printer use? I was looking at the manual and it appears to be an MK8 style. The manual suggests a limit of 260C, so I'm guessing it is a PTFE lined heat break? If PTFE, what is the condition of it? The manual also suggests printing speeds of 60mm/s with travel of 80mm/s, so it may be worth limiting your speed for testing purposes. The large z seams

by snakergy - Printing

Re: print quality awfull out of the blue - 5 years ago

QuoteMCcarman I have seen similar but don't know the cause. I would suggest its an extrusion issue. I don't know which way you are printing but I think you get an under extrusion after a stop or slow print point and the stringy filament does weird things. The diagonal faults are a bit of a clue as we see that where there is nozzle oozing. oozing being the equivalent of under extrusion. No idea w

by snakergy - Printing

Re: print quality awfull out of the blue - 5 years ago

QuoteDavid J This may be a silly suggestion - feel free to ignore it - but I have been caught out in the past with a delta, when one or two of the toothed pulley fastening screws worked loose on the motor shafts. Not enough to fall off or stop rotating, but enough to allow a few degrees of rotation, depending on where the flat of the shaft was in relation to the pull on the drive belt. This was

by snakergy - Printing

Re: print quality awfull out of the blue - 5 years ago

QuoteOhmarinus Quotesnakergy Actually my cooling fan is cooling kind of intermittently, but i thought it was beacause of some weird setting i may have made in my slicer. As soon as i am home i will change the fan and check if another fan is working any different! I mean the cooling fan that cools down the stepper drivers/controller so not the part cooling fan. So i have checked my stepper dri

by snakergy - Printing

Re: Druckqualität plötzlich nicht nachvollziehbar schlecht - 5 years ago

QuoteGlatzemann Hast du bereits das Antriebsrad im Extruder geprüft? Eventuell ist das zugesetzt oder locker? Könnte auch sein, dass der Extruder überhitzt und/oder Schrittverluste hat. Noch ein Tipp: Einige PLA-Sorten (z.B. colorFabb XT) und auch PETG dürfen nicht nur nicht zu schnell gedruckt werden, sondern auch nicht zu langsam. Da kann es zu extremen Problemen führen. Also den Extruder hab

by snakergy - Allgemeines

Re: print quality awfull out of the blue - 5 years ago

Actually my cooling fan is cooling kind of intermittently, but i thought it was beacause of some weird setting i may have made in my slicer. As soon as i am home i will change the fan and check if another fan is working any different!

by snakergy - Printing

print quality awfull out of the blue - 5 years ago

Hello, first of all thank you in advance for your help. I have troubles with my printer for a few months now and i have tried a lot, but without any positive results. That's why i thought to post in this forum and ask for your help, maybe someone here is able to help me. Getting to my problem: I'm a proud owner of a delta-printer, the Anycubic Kossel plus (Bowden, Heated bed, linear Rails). The

by snakergy - Printing

Druckqualität plötzlich nicht nachvollziehbar schlecht - 5 years ago

Hallo zusammen, erstmal vielen Dank im Voraus. Ich habe jetzt seit Längerem Probleme mit meinem Drucker und habe schon wirklich viel probiert, bis jetzt leider ohne Erfolg. Daher dachte ich mir, dass ich mich mal hier an das Forum wende, vielleicht kann mir hier ja jemand weiterhelfen. (Ich hoffe die ausführliche Erläuterung ist nicht zu umfangreich) Zu meinem Problem: Ich bin stolzer Besitzer

by snakergy - Allgemeines