Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 17 of 17
Quotemaralb
I also have problems on prints near the hole
but I think it is the fault of slicer
be a difficult problem to understand
use delta printer Repetier 0.92.3
Sliced CuraEngine
I use Curaengine too. Maybe you can update to 1.0.6, it's ok, but for unknown reason1.5.4 is not working well.
by
frankleng
-
Repetier
see words on pic. I don't know what caused this,and whether i should make some settings somewhere.
The slight "groove band" effect usually happens on where there is a hole.
by
frankleng
-
Repetier
Thank you software develpment guys, 1.5.4 is great for me until now.
I just updated from 1.0.6 to 1.5.4. Uninstall 1.0.6 first and install 1.5.4
Until now, it's great.
Here are few features i found:
1, Dial size zoomed to right size (1.0.6 can not show all button, especially the Home and Z button).
2, Dial button disabled when printing. This is pretty handy to prevent mis-clicking on anyone. Onl
by
frankleng
-
Repetier
I'm using 1.0.6 and grid support for some prints. (cura engine)
I found that if i do not use grid support, holes are better printed.
But, with grid (for some prints, i need to use this rather than Line support), the hole not printed well, the hole is just liken rotten thing.
After observavtion, i found that the hotend won't run a circle, instead when printing the hole, it complete just about 2/3
by
frankleng
-
Repetier
I don't know how to raise Z after pause. I used to make mistake like this:
I raised Z when printing, then my printer print at a extradionarily snail crawling speed, which is of course wrong. I have to restart it.
Why not raise it before printing?
You can use auto bed leveling (if you have) to make sure your print is on the same level. After print, you do not need to raise it at all.
by
frankleng
-
Repetier
sorry, i don't know either. I'm still using 1.0.6. You'd better backup your setting from Reg.
by
frankleng
-
Repetier
Repetier frequent update now, more stable? or new features?
after updating from 1.0.6 to 1.5.0, 1.5.3, now, it's 1.5.4 just in weeks.
new feature? bug fix? more stable?
I really want to know details.
By the way, thanks for your effort to provide such a good software.
by
frankleng
-
Repetier
when printing, the function (moving x,y,z) i think should be disabled unless you press paul first. Otherwise, if you mistakenly press any button, your printer stops. That would be tragic. Of course, this is only my idea.
by
frankleng
-
Repetier
the last version is 1.0.6, why is it 1.5.0 suddenly? anyone knows?
I wanna know more details too.
by
frankleng
-
Repetier
Turns out i should set "reset on connection" to DTR-high-low".
by
frankleng
-
Repetier
I have two 3D printers. I used to control both with repetier, and they work well.
Recently, I upgraded firmware (marlin) for one of them. After that, the newly upgraded machine can not be controlled by Repetier,
the heatbed icon won't appear under manual control. For once, i succeeded, but only once. After that, no luck,
and LCD screen is totally dead there. But, I can control it with Cura even
by
frankleng
-
Repetier
I uploaded incorrect firmware to Ramps 1.4 control board. Now, there is no screen display and it alarms "beep"..
by
frankleng
-
Repetier
I want to control two printers at the same time. However, i did not see add button on Printer setting page.
by
frankleng
-
Repetier
Thank you. Then i will leave it be.
by
frankleng
-
Repetier
After some hours, the live preview stops updating. Anyone knows how to solve this?
It becomes transparent.
by
frankleng
-
Repetier
I did not think the codes works for cura does not work for repetier curaengine.
Now, after some tests, it's ok. Thank you very much.
by
frankleng
-
Repetier
slicing with curaengine, estimate printing time not working, it's 0.
when switched to slic3r, it's working.
How to solve this?
by
frankleng
-
Repetier