Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 25 of 25
Ak si sa dostal az sem pravdepodobne vies co je to RepRap. RepRap je open source. Existencia open source projektu stoji a pada na komunite. Toto forum je venovane slovenskej komunite.
by
jakub.sturc
-
RepRap Usergroup - Slovakia
Hello everybody
RepRap is starting to be popular in Slovakia. It would be nice to have a local forum to help the community grow.
Thanks
Jakub
by
jakub.sturc
-
Request a Local RepRap User Group
@misan: thank you sir.
by
jakub.sturc
-
General
Hi misan.
"Kliment's compact extruder"? I've never heard of it. Sounds sexi. Can you please share a link?
Thanks.
by
jakub.sturc
-
General
Quotevokt
Jeste se zeptam jaky prumer ?
0.5mm
by
jakub.sturc
-
Hotendy a hlavy
kupili sme od Lazsla z arcol.hu
zatial sme 100% spokojny.
by som dal este do pozrotnosti Prusa Nozzle, predpokladam, znacnu usporu na postovnom. na druhej strane neviem ci sa uz naozaj predava.
by
jakub.sturc
-
Hotendy a hlavy
Co sa SW tyka, nemapadaju mi nejake prakticke limity. Od isteho momentu zacnes mat problem s reprezentaciou realnych cisiel, ale to by si musel zvacsovat viac ako 1000x.
by
jakub.sturc
-
FAQ & HOW-TO a odkazy
V Progressbare v Bratislave maju dva.
by
jakub.sturc
-
Mechanika
Pouzivame obycajne sklo, vyslo nas aj s odrezanim na 2€, sklar co nam ho daval, povedal, ze ak nam praskne, mame prist a da nam nieco odolnejsie. Zatial neprasklo.
Na druhu stranu je pravda, ze nas HB sa zohrieva velmi pomaly a 110°C nedosiahne.
by
jakub.sturc
-
Novinky, nápady, nová řešení
Finally we did some measurements and heated bed is under 11.2V so it seems that in out case it's not root of the problem.
On the other hand aluminium plate under HB (see photo above) is getting real hot. So I am starting to believe that heat is leaking through it.
by
jakub.sturc
-
General
Quotejininjin
How do I calibrate the extruder steps per mm?
There is a great tutorial to Slicer. See step 1
by
jakub.sturc
-
General
Our PCB Heatbed (MK1) can't reach 100°C. After 10 to 15 minutes it reach 80°C maybe 85°C but I cannot recall if it ever goes over 90°C.
What's the most probable source of this problem?
• We have only 350W ATX power source with 14A cord. Is it too weak?
• Poor (air and cork) from underlying aluminium plate?
• Low ambient temperature 18°C
• Something else?
Thank you for ideas.
Here is the i
by
jakub.sturc
-
General
I am going through Arcol.hu Hot-end v4.0 assembly manual. There are two screw holes on heater block. You can see it on several pictures. I am wondering what's the purpose for this holes? For termistor there is another hole (from upper side between this two) and I cannot found any use for them in assembly guide. Do you have any idea?
by
jakub.sturc
-
General
QuoteJakub
Je možné pak od tebe dostávat info jak ti to jde?
Nejake forky z prvej build session su tu.
by
jakub.sturc
-
Mechanika
QuoteJakub
Je možné pak od tebe dostávat info jak ti to jde?
Mame wiki, ale to su skor pracovne poznamky, ako nejake medium na dokumentovanie postupu. Chcelo by to nejaky blog. Preberem to s chanami.
by
jakub.sturc
-
Mechanika
QuoteJakub
tak jak? Sehnal si vsechny dily?
Vsetky diely co sme objednavali zo zahranicia uz mame. Trapne je, ze nam chybaju sroubiky a matky z lokalneho zeleziarstva :-|
Kazdopadne mame vyfrezovany hotend a kamarat dal dokopy elektroniku.
by
jakub.sturc
-
Mechanika
Ano planujeme. Do konca tyzdna by sme mohli mat 95% suciastok a cez vikend dufam, ze zacneme stavat.
by
jakub.sturc
-
Mechanika
QuoteJakub
V seznamu soucasetk je cca 80-90 matek M8, je u nich napsany typ "fastener".
"Fastener" nie je typ matky, matka je "fastener". Doslovne prelozene to znamena "spojovací prostředek".
Co sa tyka matiek budeme kupovat uplne obycajne s vynimkou extrudera na ktory pouzijeme jednu Nyloc M8 (se silikonem proti povoleni) a styry M4 s kridielkami :-).
)
Kazdopadne opakujem, ze som ziaden RepR
by
jakub.sturc
-
Mechanika
QuoteJakub
Když jsem koukal na stránku Jakuba Šerýcha, tak ten používá Sanguinololu, ale na několika stránkách jsem narazil na elektroniku RAMPS 1.4.. Co je lepší?
Neviem. Pre RAMPS sme sa rozhodli cisto oportunisticky. Kamarat s ktorym to skladam ma skusenosti s Arduinom a Joachim (reprapsource.com) ho mal zrovna na sklade, tak sme setrili na postovnom.
by
jakub.sturc
-
Mechanika
QuoteJakub
Jinak mohl bych tě poprosit o seznam věcí co jsi nakoupil na reprapsource.com ?
Veci este nedorazili, ale toto sme v pondelok objednali. Je tam jeden extra Wade's extruder, ktory sme brali pre kamarata. Jeden je uz zahrnuty v tom Prusa Mendel Kit Material.
8x Bearing 608 ZZ
1x PCB Heatbed Mk1
1x Microswitch-Set (3 pcs)
1x Wade bearing kit
3x Bearing 608 ZZ
4x A4988 Stepper Mot
by
jakub.sturc
-
Mechanika
Pozor! Ziaden RepRap som nepostavil, moje omedzene znalosti su cisto teoreticke.
S odlisnostou jednotlivych dielov sa budes musiet naucit zit. RepRap je zivy open source projekt a vacsina kusov je oreginal. Treba objednavat od niekoho kto tomu rozumie a vie aj poradit. My sme v pondelok objednali takmer vsetko z reprapsource.com.
Najnovsiu verziu Prusu najdes na githube.
Bohuzial chyba dokum
by
jakub.sturc
-
Mechanika
Hello there, I am new here. I am from Bratislava Slovakia and with a few friends we are planning to build out first RepRap. We choose Prusa Mendel, however there are still few variations which bother me.
Which version should we build? Since this is out first build we want to build the most documented and well-tried model. That is Prusa Mendel from wiki.
There is also Prusa Mendel v2 on GitHub.
by
jakub.sturc
-
General