The SKR Pro does not have EEPROM and i did not enable the emulation.von Srek - General
I interpreted the two nozzle setup as dual x, which would require 6 drivers.von Srek - General
M119 shows all endstop triggered after both homing tries, the first that works and the second that doesn't. I already ruled out immediate endstop problems. Z doesn't move after the incomplete homing, regardless the speed. Only if is set Z pos to a negative value i can get it to move, see Viktors and my post above. If it moves the speed is correct. M503 delivers this 14:48:29.638 : N20 M503*23 14von Srek - General
The Duet has only 5 stepper drivers so you need to purchase a duex extension from the beginning.von Srek - General
Definitly not a pin or endstop problem. The endstop status for all 4 is reported correctly at all times. Edit: Interestingly the first homing did work when i filmed this, but a subsequent one didn't.von Srek - General
Es ist ein Mendel Setup, der Z Endstop sitzt unten und wird beim herunterfahren der X Achse mechanisch ausgelöst. Ich habe zum Test Z/Y vertauscht um sicherzustellen das Endstop und Motor ok sind. Die komplette Firmware ist hier bzw. hier Edit: Hier noch ein Video Seltsamer Weise funktioniert diesmal das erste Homing, das zweite, dann aber nicht mehr.von Srek - Allgemeines
A RADDS with Marlin 2.0 will do the job, it did for my dual X printer for a year until i damaged it. I'm currently trying a Bigtree SKR Pro 1.1 as a replacement but have some firmware problems. Go for 24V for the printer, you don't even need the 220V heatbed then. I have a 220V in my old printer and 24V in all my newer ones. 24V is much preferable due to safety considerations.von Srek - General
Leider hat sich immer noch keine Lösung gefunden, hat noch jemand eine Idee?von Srek - Allgemeines
Does anyone else have any idea? This realy has me stumbedvon Srek - General
Das klingt als ob das Hotend überhitzt, genauer, der Teil oberhalb der Heatbrake wird zu warm. Dadurch schmilzt das Filament zu früh auf und verstopft das Hotend. Evtl. Reicht schon eine etwas bessere Kühlung des Hotends.von Srek - Allgemeines
I don’t know the name, but maybe i can offer an alternative. I resolved a similar problem with a printed part that has a hollow split shaft on which the bearing is put. The hole in the shaft was designed to expand when a screw is put in, thus fixing the bearing without any play, while the screw gave the setup the necessary stability.von Srek - Reprappers
So far i only controlled the printer via the LCD or Repetier Host. In Repetier Host i set the printer size correctly and home to 0/0/0, just like always do.von Srek - General
Please find config and config_adv attached. Thank you very much for your help. Next time we meet the beer is on mevon Srek - General
The second command set actually worked. I have problems understanding why though since Z_MIN_POS and Z_MAX_POS seem correct to me This is from configuration.h // The size of the print bed #define X_BED_SIZE 215 #define Y_BED_SIZE 200 // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS -30 #define Y_MIN_POS 0 #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZEvon Srek - General
The new position is shown, but nothing actually moves 19:31:50.559 : N14 G28*38 19:31:50.559 : echo:Active Extruder: 0 19:31:56.923 : echo:Active Extruder: 0 19:31:56.923 : X:-30.00 Y:0.00 Z:0.00 E:0.00 Count X:-2400 Y:0 Z:0 19:32:13.806 : N15 G92 Z10*93 19:32:13.806 : X:-30.00 Y:0.00 Z:10.00 E:0.00 Count X:-2400 Y:0 Z:0 19:32:23.488 : N16 M114*16 19:32:23.488 : X:-30.00 Y:0.00 Z:10.00 E:0.00 Cvon Srek - General
Dann wird die neue Zielposition ausgegeben, aber es bewegt sich nichts. 19:31:50.559 : N14 G28*38 19:31:50.559 : echo:Active Extruder: 0 19:31:56.923 : echo:Active Extruder: 0 19:31:56.923 : X:-30.00 Y:0.00 Z:0.00 E:0.00 Count X:-2400 Y:0 Z:0 19:32:13.806 : N15 G92 Z10*93 19:32:13.806 : X:-30.00 Y:0.00 Z:10.00 E:0.00 Count X:-2400 Y:0 Z:0 19:32:23.488 : N16 M114*16 19:32:23.488 : X:-30.00 Y:0.00von Srek - Allgemeines
Zum Test habe Ich Motor und Endstops von Y und Z vertauscht, das Verhalten war dann auch getauscht. Motor und Endstop sind damit als Ursache ausgeschlossen.von Srek - Allgemeines
Just to be sure i switched motor and endstop of Y and Z, the behavior was switched as well so i can rule out motor and endstop.von Srek - General
If i have HOMING_BACKOFF_MM defined it shows the defined value, otherwise 0. An actual movement after first contact with the endstop does not happen.von Srek - General
Er steht auf Null. Testweise hatte ich aber auch schon eingestellt das er nach dem Homing auf +5 mm geht, das hat aber nichts geändert.von Srek - Allgemeines
Nei, aber ich hatte sie zum Testen zwischenzeitlich aktiv gemacht, was aber auch keine Änderung im Verhalten gebracht hat.von Srek - Allgemeines
Hi all, i had to replace the electronics and Firmware of my DuoCube printer. All motors, endstops, hotends and the heatbed work fine. I use a Bigtree SKR Pro 1.1 with Marlin 2 and TMC5160. The endstops test out good using M119 and trigger reliably. After initial homing the Z axis gets stuck on 0, even the short move back and for does not happen anymore. This does work on both x axis and Y. Aftervon Srek - General
Ja, ich kann XY bewegen, die Hotends und auch das Heizbett tun wie erwartet, ich sehe keine anderen Seiteneffekte.von Srek - Allgemeines
Nein, M119 erkennt es eindeutig korrekt als Z Min und beim initialen Homing stoppt Z ja auch sofort bei Endstop Auslösung.von Srek - Allgemeines
Moin, ich musste die Elektronik an meinem DuoCube tauschen und dabei leider auch die Firmware ersetzen. Ich habe also einen Drucker der mechanisch und elektrisch (Motoren/Endstops/Hotend/Heatbed) in Ordnung ist, dessen Elektronik und Firmware aber neu sind. Ich habe mir ein Bigtree SKR Pro 1.1 besorgt und Marlin 2.0 drauf laufen. Soweit so gut. Alle Endstops funktionieren korrekt, Kontrolle mittevon Srek - Allgemeines
Ihr arbeitet ja an der Materialübersicht, könnt ihr da bitte bei den Materialien auch die präferierte Druckbett Oberfläche listen? Ich habe z.B. echte Problem herauszufinden auf was ich ASA drucken sollte. Danke für den Hinweis mit dem ABS Natur, bestellt Grüße Björnvon Srek - Kommerzielle Angebote & Produktvorstellungen
QuoteNetjir Hey Shrek, wir arbeiten an 2kg Spulen ABS! Brauchst du soviel ABS derzeit?! Kannst du mir schnell eine Mail zukommen lassen, dann kümmere ich mich um die Produktion. Beste Grüße, Marco Du hast Mailvon Srek - Kommerzielle Angebote & Produktvorstellungen
Quotesechsteelementdas Marlin-Set Heißt übrigens Merlin, benannt nach meinem schwarzen Kater der die Entwicklung geleitet hatvon Srek - Extruder, Hotends & verschiedene Materialien
Arduino Due based boards, like the RADDS can be programmed using Arduino IDE. The other boards use SD cards with boot files, similar to smoothie. For thos you need Plattform IOvon Srek - Controllers
Ich selber habe immer nur 1.75 verwendet, aber meines Wissens gibt es diverse Leute die 1.7 nehmen. Das sollte nicht kritisch sein so lange du beim Einschrauben sorgfältig arbeitest. Protoworxx hat da ein geniales kleines Werkzeug im Angebot.von Srek - Extruder, Hotends & verschiedene Materialien