@Hallo Christian Deine Endstop settings stimmen nicht. Die Düse ist immer der 0 Punkt ( Z min Endstop ) Du hast das eingestellt X homing in negative direction direction (towards min endstop). (X_HOME_DIR) Y homing in negative direction direction (towards min endstop). (Y_HOME_DIR) Z homing in negative direction direction (towards min endstop). (Z_HOME_DIR) X homing in negative direcvon Micro3D - Software
@Hallo Stell erst das mal wieder auf den Standart ein ( Ich weiß du hällst nichts davon ) #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow #define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points //#define Z_HOMING_HEIGHT 5 Jetzt noch mal testenvon Micro3D - Software
@kleinerDrache Las mich raten du kannst nicht mit Repetier-Horst in das negaive fahren ? Ist bei mir auch so. Versuch mal über das LCD zu machen Home ( XYZ ) Bewegen ( ein stück papier unter der Düse legen ) Z Jetzt runter fahren bis das Papier kratzt ( z.b. in Z steht -2.9 dann den Z-Versatz unter Einstellungen ein stellen )von Micro3D - Software
@Hallo Quote Was ist der praktische Unterschied zwischen G29 (3 Punkt) und G32? Das G32 ist für Repetier FWvon Micro3D - Elektrik & Elektronik
@Hallo LazyBee Quote Ich habe gerade noch einen Blick auf das Display geworfen. Dort steht bei Z 6,4 und G28 Z verboten. Was bedeutet das? #define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2)+ X_PROBE_OFFSET_FROM_EXTRUDER // X point for Z homing when homing all axis (G28). // #define Z_SAFE_HOMING_X_POINT (40)von Micro3D - Elektrik & Elektronik
@Hallo LazyBee Was für werte hast du in Simplify darin bei Z-Min 0.0?von Micro3D - Elektrik & Elektronik
@Hallo LazyBee Hast du schon das probiert? G28 Z G1 Z0 Bin ich der einzige der kein G92 beim Z-Level benutzt ( ausser beim Extruder )von Micro3D - Elektrik & Elektronik
@Hallo Hans Du hast eine PNvon Micro3D - Schwarzes Brett
@Hallo Hans Ich habe auf deiner Config die neue Marlin 1.1.7 seit heute gibt erstllt. Marlin-1.1.7 Ich habe das EEPROM eingestellt , ist komfortabel steps ein zu stellen. // // EEPROM // // The microcontroller can store settings in the EEPROM, e.g. max velocity... // M500 - stores parameters in EEPROM // M501 - reads parameters from EEPROM (if you need reset them after you changed them tempvon Micro3D - Schwarzes Brett
@Hallo Hans Ich stell dir eine neue Marlin 1.1.6 zu sammen , da sind noch ein paar fehler darin.von Micro3D - Schwarzes Brett
@Hallo Hans Quote Hab das jetzt mal mit dem Code G1 X0 Y0 gemacht nur leider keine Reaktion Keine Achsbewegung aus der Homestellung wie auf dem Foto gezeigt Mach noch mal ein test G28 X0 Y0 Bei Repetier Host G1 X10 Y10 Stell noch mal deine Config.h hiereinvon Micro3D - Schwarzes Brett
@Hallo Hans Quote Hab das so gemacht Du beschrieben hast aber bei Eingabe des G-Codes G28 verfahren die Achsen wie auf dem Foto zu sehen Hast du es so gemacht dann ist das richtig. Sende mal ein G1 X0 Y0 dann fährt er auf 0 // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS -13 #define Y_MIN_POS -28 #define Z_MIN_POS 0 #define X_MAX_POS 220 #define Y_MAX_von Micro3D - Schwarzes Brett
@Hallo Hans Quote Was für Werte müssen da rein ? alles -1 ? Du hast X Y Z MIN Endstops , dann -1 Änder das mal /** * Default Axis Steps Per Unit (steps/mm) * Override with M92 * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] */ #define DEFAULT_AXIS_STEPS_PER_UNIT { 80.00, 80.00, 4000, 132.12 } Änder das mal und drück z.b. mal X Endstop ( gedrück halten ) undvon Micro3D - Schwarzes Brett
@Hallo Hans Das ist leider nicht ganz richtig -1 für MIN Endstop und 1 für MAX Endstop. Wie bist du auf die werte gekommen b.z.w. wo für wahren die gedacht? // Direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1] #define X_HOME_DIR -21 #define Y_HOME_DIR -32 #define Z_HOME_DIR -1 Deine linke Z axis anti wobble kupplung anschauen , da simmt was nicht?von Micro3D - Schwarzes Brett
@Hallo Hans Quote Gerne würde ich hier mal meine Marlin Einstellung hierzu laden weiß leider nicht wie ich die hier hochladen kann So wie du die Fotos hochladen tust, nur wählst du die Config.h ausvon Micro3D - Schwarzes Brett
@Hallo luclass bist du da sicher das die werte stimmen , ich glaub das nicht? Ist das ein P3Steel rahmen so wie P3steel - toolson edition - MK2 /** * Default Axis Steps Per Unit (steps/mm) * Override with M92 * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] */ #define DEFAULT_AXIS_STEPS_PER_UNIT { 200, 200, 800, 250.04 } // Originalwerte 80,80,4000,500 /** *von Micro3D - Allgemeines
@Hallo Armin Quote Ich habe gestern noch die Einstellungen von Micro genutzt hochgeladen und seit dem Druckt der Drucker ... Quote Auch mit den MK8 Extruder waren die Schritte von 101 die ich bereits vorher hatte die richtigen werte. Bei mir war nur das Problem das wohl im Eprom (M503) andere Werte hinterlegt waren. Daher hat es nichts gebracht die werte im Quellcode einzustellen, da immer wivon Micro3D - Allgemeines
@Hallo Luclass Deaktiviere mal das , das ist für Manuelle BED_LEVELING per Lcd /** * Use the LCD controller for bed leveling * Requires MESH_BED_LEVELING or PROBE_MANUALLY */ //#define LCD_BED_LEVELING Hast du auch vom aufbau ein paar Bilder und Config.h Bittevon Micro3D - Allgemeines
@Hallo Quote Was sind bei einem MK8 Extruder die default Steps? Ich habe 16 Microsteps wenn ich mich nicht täusche (alle Jumper gesteckt) 152 Stepsvon Micro3D - Allgemeines
@Hallo Armin Quote Der Motor Strom ... Ich habe Nema 17 Motoren mit 1,7A ... Wenn ich nun an dem Poti messe habe ich dort eine Spannung von =1,7A*(8*0,1) E=1,35V Y=1,38V X=1,35V Z=1,36V Mit dem A4988 Treiber ist der Strom viel zu hoch , mach mal X ,Y, E 0.4 und bei Z 0.8v 1A*8*0,05=0,4v bist du sicher das das richtig ist? /** * Default Axis Steps Per Unit (steps/mm) * Override with M92von Micro3D - Allgemeines
@Hallo luclass so klapp es bei mir #if DISABLED(ENDSTOPPULLUPS) // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined //#define ENDSTOPPULLUP_XMAX //#define ENDSTOPPULLUP_YMAX //#define ENDSTOPPULLUP_ZMAX #define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_YMIN #define ENDSTOPPULLUP_ZMIN #define ENDSTOPPULLUP_ZMIN_PROBE1 #endif // Mechanicalvon Micro3D - Software
@Hallo Quote Wie kann ich prüfen (gibts da einem M-Code) ob die Endstops korrekt ausgewertet werden ? M119 was für ein endstop typ hast du sowasvon Micro3D - Software
@Hallo Änder das mal um // Manually set the home position. Leave these undefined for automatic settings. // For DELTA this is the top-center of the Cartesian print volume. //#define MANUAL_X_HOME_POS 0 //#define MANUAL_Y_HOME_POS 0 //#define MANUAL_Z_HOME_POS 0von Micro3D - Software
@Hallo ihr beide Quote geflasht mit Arduino 1.0.6. Aber wie gesagt, es ist das gleiche Verhalten wie mit allen Firmwares(auch die mitgelieferte 1.0.1. Auch die vertex-m1.0-v1.4-h2 von der Vertex Downloadseite machts falsch. Das liegt an der alten Marlin version fangen wir mal an mit die MIN werte , die MIN werte dürfen nicht größer als 0 sein ( können aber negative werte haben , X_MIN_POS -11von Micro3D - Software
@Hallo Quote meinst Du die configuration.h aus der Firmware? ja genauvon Micro3D - Software
@Hallo hättest du für uns eine Config dann könnte man dir besser helfenvon Micro3D - Software
@Hallo veruch mal das /** * LCD TYPE * * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD. * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display. * (These options will be enabled automatically for most displays.) * * IMPORTANT: The U8glib library is required for Full Graphic Display! * */ //#define ULTRA_LCD // Character based //#define DOGLCDvon Micro3D - Software
@Hallo sveni83 Man sollte auch das richtige boards wählen. Du hast Rambo gewählt // The following define selects which electronics board you have. // Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD 301 #endif So müsste es richtig sein // The following define selects which electronics board you have. // Please choose the name from boardsvon Micro3D - Software
Quote Hast Du ein anderes Format ? Marlinvon Micro3D - Software
@Hallo Hans Quote Wenn ich den Befehl G0 X0 Y0 eingebe fährt der Drucker ins Homing d.h er parkt dort Wenn ich aber über Prontoface den mittleren Button drücke fährt der Drucker fast bis zur Mitte des Bettes und bleibt dort Er macht ja nur was du in gesagt hast , wenn du in sagst fahre auf null dann fährt er auch auf null (G0 X0 Y0) Das mit dem Home Button hast du ja definiert in Marlin. Hievon Micro3D - Software