Show all posts by user

Re: I crushed my Duet Board! - 10 years ago

Thx for your help now my Printer is working again! awesome stuff

by stom - Ormerod

Re: I crushed my Duet Board! - 10 years ago

Big thx for your help David! everythink worked fine also the link to duet3D Homepage was very helpful! The last problem i have now, all my motors move in the wrong direction i didnt found a solution online :/ Maybe someone already had this problem ?

by stom - Ormerod

Re: I crushed my Duet Board! - 10 years ago

Hello, i got my DUET 0.85 Board yesterday. I want to use the wiring diagramm of the think3dprint3d site. Most of the connections of the wiring diagramm are clear for me! 1. 5V Connections Do i have to supply the board with 5V ? I guess when i dont connect the board to 5V, the USB Cable have to be connected to the board !? 2. Hotend Wiring At the Omerod 1 Wiring diagramm the Hotend needed 4 Wi

by stom - Ormerod

Re: I crushed my Duet Board! - 10 years ago

I prefer to spend more money and have less problems also the changes of the Duet 0.8.5 sounds reasonable. so i will order a Duet 0.8.5. thanks for your help and for the detailed response! br

by stom - Ormerod

I crushed my Duet Board! - 10 years ago

Hello, unfortunately i destroyed my duet board through a short circuit now i want to buy a new one. My omerod is now about 1 1/2 year old. I think there have been some changes of the board since i bought my printer. Also when i look at the wiring instructions of the omerod 2 i see significant changes of the wiring diagram. What must/should I consider when i buy a new Duet Board ? Is the wiri

by stom - Ormerod

Re: What rod for a Tallerod? - 10 years ago

hi, maybe those postings are helpfull for you br

by stom - Ormerod

Re: X-Axis & Z-axis homing problem - issue with Proximity Sensor - 12 years ago

Hello, i had also the problem that my sensor gives me a value about 500 when i am putting a white paper under the sensor. Unfortunately i didnt find the forum post which helped me. i used the wrong pin for the newer firmware version. NOTE: From firmware 0.78 (3rd July 2014), the pin the proximity sensor uses has changed. On EXPANSION header, it has moved from the 9th pin from the right, bottom

by stom - Ormerod

Re: Orthogonal Axis Compensation - 12 years ago

yes i messured it that way. the graphic is realy good to understand how the Axis Compensation should work and now i understood also for what the S Value is good for. but my ormerod have more mechanical issues i have to look for, because i tried to print iamburnys Z Gears and the gear doesn´t fit on my z motor

by stom - Ormerod

Re: Orthogonal Axis Compensation - 12 years ago

hi again, i used the adjustable bed to keep the Values of the bed compensation as small as possible and now my "Orthogonal Axis Compensation" seems to be working. thank you for your help

by stom - Ormerod

Re: Orthogonal Axis Compensation - 12 years ago

okay thx for your help. i haven`t found the mechanically failure. i will also try the adjustable bed mod i hope this will solve my problem

by stom - Ormerod

Re: Orthogonal Axis Compensation - 12 years ago

thanks for the fast reply. okay first of all i will try to get mechanically a bit closer to the level. but beside that mechanically issues,when i delete the "Orthogonal Axis Compensation" from setbed file. The Printer starts normaly at the "zeroed" position i teached.

by stom - Ormerod

Orthogonal Axis Compensation - 12 years ago

Hi again ! I have again some Problems with my omerod Printer. At the moment i try to the „Orthogonal Axis Compensation“. First of all i do not know exactly if measured the distance „between the tip of the projection near the angled corner and the center of the end of the screw“ correct (picture 1). because i measured a distance of 75 mm and not 78 mm. The second problem i have, when i put the

by stom - Ormerod

Re: Stops at 3.6 mm - 12 years ago

thank you guys. i finished my first print this moment !!!!!

by stom - Ormerod

Re: Stops at 3.6 mm - 12 years ago

ah okay thank you. i will try it

by stom - Ormerod

Stops at 3.6 mm - 12 years ago

Hi RepRap Community, unfortunately I found no post which had an solution for my Problem. Since a few weeks I am able to print. But only (exactly) 3.6 mm of my objects. After 3.6 mm the printer stops without any recognizable reasons. Had someone also this problem ? or has someone an idea how I can identify the problem of my printer ? I use Slic3r 1.01 with the standard settings My Printer Ve

by stom - Ormerod

Re: proximity sensor - 12 years ago

Hi and thanks for your help finaly i could continue to work on my RepRap so i separated the two soldered joints. Lo and behold it works. After that, i “homed” my axies, this worked also. But after that, my “heated bed” Senor didnt worked any more. I also could not start the heated bed and heater on the hot end. All three things have already worked. So I removed the firmware, that i have comp

by stom - Ormerod

Re: proximity sensor - 12 years ago

No thx i will try to fix it by my self ! but i have to wait until next week thanks for your help, i hope this is the failure. regards Stom

by stom - Ormerod

Re: proximity sensor - 12 years ago

Hi, thank you for the quick response and sry for my late answer, bacause of my work i am not often at home at the moment! I have read your suggestions. So i wanted do measure the Voltage on the four pins of my Sensor. During this, i have noticed that the contact of my blue and the black wire are connected trough the joint. That should not be? Thanks Stom

by stom - Ormerod

proximity sensor - 12 years ago

Hello RepRap Community, I'm almost done with the construction of my RepRap printer. At the moment i got stuck at captiel "Commissioning" in the manuel. more precisely at the commissioning of the proximity sensor. The Problem is when i send the command G31, i get a Value between 200 and 400 back. When i put a piece of paper under the sensor, the Value doesn`t change. They Value is always located

by stom - Ormerod