Quotedroftarts Hi shauna We've had a couple of people report this problem, since the v1.09 firmware update. The PID values (which control the heating) were changed. Generally, this is okay - we tested in house, and didn't see any problems. But if there is something not working quite correctly, it can cause the heater to take too long to heat up. It tends to hit the temperature about 10C below taby shauna - Ormerod
Quotezombiepantslol You must select the first tool by sending "T0" first before you can heat up and extrude any filament. Also see I did have the tool selected with all my original problems. Quotezombiepantslol If your nozzle takes a long time to heat up, the easiest way to speed it up would be to increase the 'S' term via M301. You could try this out by sending M301 S1.1 which will increaseby shauna - Ormerod
Hi, So I'm having some trouble getting my Ormerod 2 to print test pieces. The hot end doesn't always heat up and when it does the printer moves as if was printing but it does not extrude anything. The extruder gears don't turn. When I give manual commands in pronterface I can get the filament to extrude after sending G032 P1. When I heat up the hot end in Pronterface it heats up very slowly. Iby shauna - Ormerod
Quotezombiepantslol Your output looks good to me, and it tells me you already have a tool defined. FYI you do this via M563 in your config.g file. Send "T0" (or T) to select the tool, then you will see that M105 reports the current temperature as seen in the instructions. Also check out this article. The H0 and H1 values report the current and target temperatures for all configured heaters. Youby shauna - Ormerod
Hi guys, Another problem, this time with the temperatures being reported to both Arduino and Pronterface. M105 gives me a response: ok T: B:21.3 HO:21.3/-273.1 HI:21.3/-273.0 It mentions in the commissioning instructions that you have to define the hot end tool, T, but never says how to do this. Also I suspect the H0 and HI responses are due to a problem with my config.g file. My Firmware vby shauna - Ormerod
QuoteDarathy it may be a foulty usb Cable or usb plug on the duet(which is common problem it seems). Switched the USB cable and I finally have a response from the Duet in my serial monitor!!! Thanks so much for all the help everyone!by shauna - Ormerod
Hi Guys, So my drivers started giving me trouble today. Different problems that I haven't seen before. When I plug in the printer to the USB port it is recognised as an "unknown device" in the USB controller section of device manager. It is no longer regognised as a COM port. I tried uninstalling and reinstalling Arduino IDE to no avail. I also tried downloading Adruino IDE to a different computby shauna - Ormerod
Quotedc42 That is a sign that Windows thinks the driver is already in use. I think there is a bug in that driver. Remove the USB cable from the computer, then plug it back in again. Then tell Pronterface to connect again to COM10, and see if it says anything different. When I unplug it and try to connect I get " The system cannot find the file specified" When I plug the USB back in and try toby shauna - Ormerod
Quotedmould When you flashed it, did it go through the verify stage and report that the firmware was successfully downloaded? Dave Yes it did go through the verify stage and confirm. Am I missing something? Does it need mains power? Or some file on the SD card? Configuration files modified?by shauna - Ormerod
Hi guys, So I'm getting no response at all from the printer. I flashed the due with the firmware and it is being recognised in device manager as "Arduino Due (COM10)". I've tried using Pronterface, in ports there are options for COM10 and COM4. COM10 is responding "Can't write to printer (disconnected?)." over and over. COM4 first says "connecting.." and then "M105" repeatedly with no response.by shauna - Ormerod
Hi, I'm new to 3D printing and I'm at the commissioning stage with my Ormerod 2. I've reached the stage where I've selected the board and port in Arduino (duet is listed for both) and in the Serial Monitor window I've selected a speed of 115200 and Newline. However I don't get a message saying "RepRapFirmware is up and running" as I should. I've tried typing M105 in the text box in the serial monby shauna - Ormerod