M111 S0 ; Debug off M550 PAnthony's Ormerod 3D Printer ; Machine name (can be anything you like) M551 Preprap ; Machine password (currently not used) M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xED ; MAC Address M552 P192.168.1.14 ; IP address M553 P255.255.255.0 ; Netmask M554 P192.168.1.1 ; Gatewaby antlvk - Ormerod
deleted*by antlvk - Ormerod
Now i cant start print, when head temperature met i just wont start and head become not active and temp are going down after that. i have T1 code. Weird. Helpby antlvk - Ormerod
my printing just wont start printing. i have T1 code. but in the web my head 1 are off after the bed met the temp. ; generated by Slic3r 1.0.0RC3 on 2014-08-30 at 11:32:14 ; layer_height = 0.25 ; perimeters = 3 ; top_solid_layers = 3 ; bottom_solid_layers = 3 ; fill_density = 0.35 ; perimeter_speed = 30 ; infill_speed = 50 ; travel_speed = 130 ; nozzle_diameter = 0.5 ; filament_diameter = 1.75by antlvk - Ormerod
Urm is this firmware for your sensor only cause i've reversed my X now, head run right way but the sensor wont stop the head and crashed to the side. *sorry found the problem already.by antlvk - Ormerod
my X head running the wrong way. i need to change something on the hardware side?by antlvk - Ormerod
Ian save the day, lol Thanksby antlvk - Ormerod
4 point leveling problem each position prop wont raise after each point detected. does it makes it not proper leveled?by antlvk - Ormerod
Still very confusedby antlvk - Ormerod
basiucally X zero position wont be at the parking spot right?by antlvk - Ormerod
where can i find guides for this?by antlvk - Ormerod
modified to divert the hot air upwardsby antlvk - Ormerod
jstck, just type G92 on the coordinate? only G92?by antlvk - Ormerod
from day one i have this problem. my ormerod not printing in the center. like 10mm to the left. So I can't print full bed as it will off the bed. anyone?by antlvk - Ormerod
Prefinity, any photos of your mk3 connection, sounds interesting and i've ordered an 12v 360w 30a psuby antlvk - Ormerod
means everything that connected to the due board also have more voltage.... ok.... next project.by antlvk - Ormerod
I try print something large with 0.78e firmware the printing goes super fast and then go slow and fast and slow again.... weird.... i turned of accelerationby antlvk - Ormerod
300w are same as 20a 12v powr supply?by antlvk - Ormerod
Upgrading to this power supply is it directly power to the Duet?by antlvk - Ormerod
Anyway to get the heatbed heat faster? I took few minutes to ten minutes.by antlvk - Ormerod
New fan duct mod from ori to bypass airflow to print ABSby antlvk - Ormerod
Mine works perfectly, thanksby antlvk - Ormerod
some detailing problem, my infill are loosy i tried make the width wider but still the same.by antlvk - Ormerod
Pause and reset won't wipte setbeg n stuffs? cool, try i laterby antlvk - Ormerod
I'm using web 0.98 and newest dc421 firmware. Still struggling of cancel a prints. If cancel in the web it will Halted the machine and i have to turn off and on to restart the ormerod. then i have to home all axis all over again and setbed.g anyway to stop a prints and if bad things happens i can stop it and clear the bed and start again. Thanksby antlvk - Ormerod
I found a 314mm x 214mm bed. Would it be easy to mod our ormerod for that larger bed? i think the frame need to changeby antlvk - Ormerod
i've move my slic3r profile .ini folder from roaming to local in the c:\programdata then my settings can be savedby antlvk - Ormerod
Thanks guys, i think my Ormerod are up and running..... Really appreciate it.by antlvk - Ormerod