non si vede niente su indiegogo!!by mdcompositi - Mercato
ho appena ordinato due di questi Ne userò uno sulla prusa i3 e un'altro sulla Tantillus! con g3d dovrei andare tranquillo! i loro g3d 4988 vanno benissimo! Appena li monto vi faccio sapere e speriamo che questa è la volta buona!!by mdcompositi - Elettronica e meccanica
procederò con l'acquisto di un'altro lcd!! qualcuno mi indica un link dove vado sul sicuro? anche se questo l'ho preso su ebay ......credo sia stata solo questione di sfiga!by mdcompositi - Elettronica e meccanica
Thank you guys for these informations! I'd like to work on cheaper system!! can you tell me some links where I can buy instead of linear guides at the lowest possible price? any of you knows? thank you in advance!by mdcompositi - CoreXY Machines
Hallo, I would like to create a system corexy using linear guides! I have seen on several sites and it is a very expensive! I was wondering if someone could tell me some links where Ican buy more economic But even in Europe! I enclose a picture of the system, I've cut plates with waterjetby mdcompositi - CoreXY Machines
si, ha l'sd dietro e comunque ho provato a modificare seguendo la procedura relativa a lcd della reprapdiscount (come descritto nella wiki) ma non va! come dice magokimbra non ho toccato niente in pins.h (dovrebbe avere i settaggi gia giusti) anche se dando uno sguardo non sono riuscito a trovare i settaggi per i pins relativi a ramps 1.4 ma vi erano solo versioni precedenti( di ramps 1.4 non neby mdcompositi - Elettronica e meccanica
ciao magokimbra e ben ritrovato!! per quanto riguarda il cablaggio penso che sia ok!! è ben serrato e le entrate e le uscite corrispondono(exp1 e exp2) quindi il mio lcd è questo? quindi oltre a decommentare la linea che dicevamo dovrei anche agire su pins.h? come vedi in allegato pins.h non compare nel mio firmware!by mdcompositi - Elettronica e meccanica
ho provveduto ad eliminare le linee di codice che non servono al mio problema così come suggerito giustamente da enricodare! procedendo per passi credo che la prima cosa da capire è quale tipo di LCD è il mio! aspetto vostri commenti Buona giornataby mdcompositi - Elettronica e meccanica
Figurati nessuna intromissione! Ci mancherebbe! Me la dai tu una mano? Cosa ne pensi del mio problema?by mdcompositi - Elettronica e meccanica
Penso che sia proprio una sterile polemica a questo punto! La sezione di codice in configuration.h relativa agli LCd è quasi la metà di tutto e chi è pratico visto che ci smanetta tutti i giorni, impiega 3 secondi ad individuare la parte interessata Anzi nel caso specifico, visto che ad es. la riga newpanel e ultipanel sono frequenti più volte per rendere più facile e veloce da parte di chi poteby mdcompositi - Elettronica e meccanica
Ciao caldamente Moderatore, a me sembra che i post inseriti siano ben esplicativi della situazione Il codice inserito, per chi va ad analizzare il problema, si scorre in modo estremamente facile per andare a vedere quale linea non va bene! non sapevo che occorre utilizzare un "tag CODE", e nemmeno credo di essere off topic!! almeno potevi dire la tua! salutiby mdcompositi - Elettronica e meccanica
il mio display è questo? sembra di si anche se il mio è rosso! quindi seguendo le istruzioni nella wiki i settaggi da fare sono di due tipi a seconda della versione di marlin! in quello che ho installato sulla mia stampante non esiste la cartella pins.h, come mai?? come posso verificare quale sia la mia versione di marlin?? c'è qualcuno che mi aiuta, magari ragionandoci insieme?? p.s. allegoby mdcompositi - Elettronica e meccanica
Aggiungo un'altra informazione! l'lcd è collegato alla ramps tramite i due cavetti agli ingressi/uscite exp1 ed exp2. ho visto anche che qualcuno dice che il problema è dovuto alla eventuale non schermatura dei cavetti che ho rivestito con stagnola(anche se credo sia una cazzata). quindi dando per scontato che il cablaggio è fatto bene e che lo schermo non è rotto, il problema deve risiedere unicby mdcompositi - Elettronica e meccanica
salve premetto che ho letto diversi post sull'argomento ma proprio non va!! ho allegato una foto dell'lcd che dovrebbe essere reprap discount(chiedo conferma!) Qui di seguito invece la configurazione di Marlin Quando attacco il cavo usb vedo sul display due linee di quadratini spero che qualcuno di voi possa aiutarmi Grazie Maurizio //LCD and SD support //#define ULTRA_LCD //general LCD suppoby mdcompositi - Elettronica e meccanica
Hallo, can someone help me? I've completed my tantillus that work very good but I need also following items to complete definetively: 1 - 16 x 2 LCD panel 1 - 20 position encoder 1 - Q-type power connector to RAMPS can someone of you has or can tell me exactly where to buy them?by mdcompositi - Tantillus
I solved this problem! I recalculated the steps per mm using this Now the printer is fine, just settle the whole thing and when I'll make some decent print I'll public some photos! with respect to the z axis, I used to twice the silicone tube and the holder printable but it happened that was cut and had to do it again. can you better explain problems regarding use of the coupler? why it createsby mdcompositi - Tantillus
I finally solved the problem of movement of the axes x and y and the printer now works! I put new printed lm8uu and works smooth! I tried to make the first prints with results are quite poor, but at least it seems that they are now passed to the next step! I'm using pronterface and kisslicer but I could not! I set all the different settings but when I start a print of a gcode generated by kissliby mdcompositi - Tantillus
@ Sublime I apologize for the error! my engines are wantai 42byghw609!by mdcompositi - Tantillus
I wanted to make a clarification about engines! I use nema 17 code 42byghw609 you say do not go well? what uses you? you could tell me the code?by mdcompositi - Tantillus
maybe you're right in part, lm8uu are printed as the igus made specifically for rotating shaft! I replaced them with metal ones because they got stuck when move! maybe part of the problem may also be what you say (waiting for a response to Sublime) but the problem is another and at this point my question is: pronterface and kisslicer are two separate things in the sense that, whereas the manuaby mdcompositi - Tantillus
I do not think that this is also why, when I had the jhead 1.75 mm, had already made a printout of the 20x20x10 cube and it was all ok! however, await sublime response , I hope to resolve as soon as possible because they are now two months that I'm on this printer and I can not make it go! p.s. I think that problem is in kisslicer settings!!by mdcompositi - Tantillus
finally I got the jhead 3mm and now the extruder works well! I also had problems moving on x and y and I preferred to replace the 4 lm8uu printed with metallic ones as you suggested now I use pronterface and kisslicer I started doing the first test printing with shameful results in practice it happens that every layer is printed in different positions, without any criterion (attach a photo of thby mdcompositi - Tantillus
you use kisslicer only for slicing! there are no manual controls and I can not figure out how to drive the printer!by mdcompositi - Tantillus
Hi, finally I've changed jhead with 3mm filament and fitted the LM8SUU! Now I have to calibrate print area because I can't print on his center!!(as you know in this area, when it seems to have solved a problem then move on to the next suddenly take a step back!) but this problem I hope to solve in these hours (repetier settings are right!) I can't solve problem about power supply, for the momentby mdcompositi - Tantillus
ok, I understand! can you confirm that I can proceed to buy these female dc with 24V max voltage? and my power supply is this thank you in advance!! p.s. tomorrow should get the 3mm jhead !!!by mdcompositi - Tantillus
ok, then what do you suggest I do to solve this issue?by mdcompositi - Tantillus
is not a problem for me to use another type of connector, the important thing is that everything works! I need a power supply for this machine because I'm using the ATX of my Prusa But what I want to do is use this power supply that I have already purchased (http://www.ebay.it/itm/251224856855?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649) can you show me a link to a product on ebay sby mdcompositi - Tantillus
perfect! for the moment I'm waiting for jhead 3 mm then I'll update the situation! I'll send also some photos about my tantillus with gt2 pulleys! for the moment I like to connect power supply using q-type connector! can you send me a link to ebay about this connector so I can buy the right item? There are different types!!by mdcompositi - Tantillus
In fact, I ordered a jhead with 3mm filament and will replace the one with 1.75 also because in this way I will have two printers with the same filaments! and in any case I think my problem is definitely related to this aspect because filament is even folded inside the tube using a 3 mm wire can I keep the 4x6 tube?by mdcompositi - Tantillus
I am using a tube of 4 mm inner diameter as the outer diameter 6mm (in BOM is 6x3!) and filament 1.75 obviously I did go over the wire nut and I slipped in jhead and then I screwed the whole thing sometimes okay but others shall not be actually the wire 3 mm is better because being more rigid flows better you know I would have taken a jhead 3 mm but I did not think there were any problems perhapsby mdcompositi - Tantillus