Sono riuscito a risolvere il problema di mirroring. Ora la stampante si posiziona perfettamente nella posizione x,y,z di home dietro l'invio del comando pronterface e basandosi sui supporti XMIN e YMIN che sono riuscito a stampare. Invertendo la direzione della X nel firmware e considerando le corrette impostazioni dell'origine finalmente ora l'effetto mirroring e' risolta. Grazie per il supportby marco1974 - Problemi e qualità di stampa
Thank you (everyone) for your support. I've printed two endstop supports: one found on thingiverse (XMIN) and the second designed by me (YMIN) and now when I says "go home" everything works so nicely and the printed part are no more mirrored. Thank you again! Marcoby marco1974 - Printing
The problem is that you are talking with a newbie that bought a kit to build its 3d printer from reprapworld.com and they forget to include something... nuts, screws... and even the belts and I would like to show you the printed items.... so poooor !!! I solved by myself all these problems and I'm using the XMAX endstop simply because in their kit I could put the endstop only in that position beby marco1974 - Printing
Ok. Dunque e' tutto vero cio' che e' in figura tranne l'YMAX che e' invece un YMIN (meglio così non modifico quella parte) QuoteRiassumendo: devo intervenire sull'asse X (modificando il valore per INVERT_X_DIR immagino) perche' considerando la nuova (e corretta) origine degli assi X-Y-Z rispetto al piatto di stampa se su pronterface clicco freccia destra il carrello si muove a sinistra (frecciaby marco1974 - Problemi e qualità di stampa
I'm sure to have inverted the X axis because in my mind the origin (0, 0, 0) was not this one I found yesterday, but the X axis started from X (MAX) point of the same image That's why I was posting the item to be printed in this way: while I had to consider it in this position: So I have to modify INVERT_X_DIR and what for me was a XMIN endstop now it should be moved as connector into the Xby marco1974 - Printing
Ottimi articoli. Secondo me ad entrambi manca un elemento fondamentale: qual'e' l'origine (0,0,0) citata nei post rispetto alla stampante ? Nel caso della mia configurazione della stampante per esempio (fino ad oggi) non e' vera la seguente immagine: Nella mia stampante, rispetto all'immagine sopra, stavo considerando l'origine degli assi (0,0,0) il punto in basso a DESTRA e non quello in baby marco1974 - Problemi e qualità di stampa
I'm finally proceeding to the print of my first objects that aren't cubes... The first items I needed were the coil filament's supports and I printed them today. My print was successful but I was wondering why in Cura the right support was in this position and when I printed it, it was printed like it was mirrored on the Y axis (when I loaded the original right support in Cura it was parallel tby marco1974 - Printing
Sto finalmente procedendo alla stampa dei primi pezzi che non sono cubetti... I primi pezzi di cui necessitavo erano i supporti per la bobina che ho provveduto a scaricare e stampare oggi. A parte alcune imperfezioni che voglio cmq risolvere mi sto trovando in questa situazione. Di seguito il file del supporto destro che avevo in Cura e che ho stampato. La stampa e' avvenuta invece in questoby marco1974 - Problemi e qualità di stampa
Grazie della pronta risposta ! Diciamo che il kit che ricevetti era tutto fuori che un kit ed ora sono costretto a rimettere il tutto in discussione. Non sto parlando di aver ricevuto la meta' dei dadi e delle viti... ma che tutte le barre ricevute non avevamo misure uguali (a due a due intendo) , che le parti in plastica erano di pessima qualita' e che mancavano addirittura le cinghie. Ora mettby marco1974 - Elettronica e meccanica
Ho la sensazione che la mia stampa sia decisamente troppo compressa e richiederebbe piu' movimento verso l'alto dell'asse Z. Ho letto anche il seguente post: dove viene calcolato il valore Z il cui valore e' lo stesso che alla fine ho inserito io. I miei due assi Z hanno un diametro di 5mm ed entra perfettamente un dado M5. Motore 1.8° a driver pololu dovrebbero essere quelli che ho io. Sono iby marco1974 - Elettronica e meccanica
I've a prusa i3 rework with RAMPS 1.4 and Marlin firmware. Today I've completed the extruder and x-y-z axis calibrations. So I tried to print a 10mm cube and this is the result: X and Y axis both are 12mm (quite good). Instead the Z axis is too much compressed: 6mm . While it was printing the extruder seemed too pressed on the filament. I currently have the following define: #define DEFAULT_Aby marco1974 - General
Many thanks for your support. Yesterday I was able to correctly setup my 3D printer. I'm attaching again my file Configuration.hby marco1974 - General
Solo per aggiornarvi che sono riuscito in questi giorni a trovare la soluzione per la mia configurazione. Posto il mio file Configuration.hby marco1974 - Elettronica e meccanica
I think the movement is right and the M119 command says all the 3 endstops are OPEN. They work very well. I've triggered them and checked with that command. If I disconnect the motor (using pronterface I mean) and then I manually move the extruder to the left (few mm near the X_MIN endstop) I can move it without problem with pronterface commands: the problem begins when I press X home button. I'mby marco1974 - General
Grazie per la pronta risposta. Ma quel parametro non si limita ad invertire la posizione di marcia nel caso si fossero invertiti un paio di fili ? A me lato pronterface se clicco X+ l'estrusore si sposta come atteso a destra, se clicco X- si sposta come atteso a sinistra.by marco1974 - Elettronica e meccanica
Hi. I've just finished to build my first 3d printer, a Prusa i3 Rework. I'm trying to modify the Configuration.h file but I'm having problems configuring home position. My three endstops are positioned exactly like in the following picture: just because I still don't have understood how you have to place yourself when describing your 3d printer (just let me know) I usually describe my 3d printerby marco1974 - General
Ciao a tutti. Ho finito di montare la mia prima stampante, una Prusa i3 Rework. Sto provando a modificare il file Configuration.h ma ho problemi nella configurazione della posizione home. I miei 3 endstop sono posizionati esattamente come quelli in foto: poiche' ancora non ho capito da che parte ci si deve posizionare per descrivere la propria stampante (fatemelo sapere ) a me viene da farlo poby marco1974 - Elettronica e meccanica