Show all posts by user
Discussioni sulle parti elettriche ed elettroniche, motori, endstop, etc. Parliamo di struttura della stampante, pulegge, madreviti, boccole, viti trapezoidali, etc.
Sanguinololu 1.3a fan - 12 years ago
Hi everyone, I'm trying to connect a fan on the heated bed pins (free for now...) I changed HEATER_1_PIN and TEMP_1_PIN to -1 and FAN_PIN to 12 Now i can start and stop the fan with the M106 M107 commands But i'm not able to change the speed with M106 Sx (with x a number between 0 and 255) With a multimeter i saw that the voltage is 0 (M107) or ~10 V (M106) but it doesn't change using M106 Sx Thaby Pacca - Sanguino(lolu)
Re: Choosing belts and pulleys - 12 years ago
now everything is clear, thanks nophead!by Pacca - Reprappers
Re: Choosing belts and pulleys - 12 years ago
Any opinion and advice is appreciated Just the last question: assuming that I want to go to T2.5 belt and pulley, if I use a 16 tooth pulley I don't have to change the firmware configuration, this means that steps/mm remain the same...so where is the improvement in quality?by Pacca - Reprappers
Re: Choosing belts and pulleys - 12 years ago
Yes thank, i already know this site...it doesn't sells GT2, my question was born from hereby Pacca - Reprappers
Re: Choosing belts and pulleys - 12 years ago
What a mess! Because I was thinking about changing belts and pulleys, having also read the post on prusa iteration 2...by Pacca - Reprappers
Re: Choosing belts and pulleys - 12 years ago
Thanks nophead! So T2.5 should be better than HTD 3M, because of the smaller pitch...by Pacca - Reprappers
Choosing belts and pulleys - 12 years ago
Hi everyone, Since i read this wiki page i'm looking for GT2 belts and pulleys, but this doesn't seems so simple (i'm in EU and i can't find good suppliers). So i was thinking if an HTD belt 3mm pitch could be the same...even if it as a greater pitch than T2.5 Thanks for the helpby Pacca - Reprappers
Re: full extruder kits $135 (AUS) 6 left - 13 years ago
What is the nozzle size?by Pacca - For Sale
Re: acquisto parti plastiche - 13 years ago
E' da un pò che sto seguendo RepRap e anche il forum RepRap italia. Sono intenzionato a costruirmi anche io una Mendel, solo che sono convinto che i prezzi siano ancora un pò altini... P.S. Pure io sono di Padova e non pensavo ce ne fossero altri di qui...inizio a pensare che anche in italia si stia espandendo questo progetto =)by Pacca - Discussioni generali - NO PROBLEMI DELLA STAMPANTE
Re: [UK] £299 Full 3d printer reprap kits April 2011 - 13 years ago
and i think that a standard kit will not include heated bed...by Pacca - For Sale
Re: [ Project ] 30$ reprap plastic parts kit - 13 years ago
yes, 300 is a big number if you want to sell only plastic parts. but you can use them for making full ready to assemble low costs kits...by Pacca - Plastic RepRap Parts for Sale
Re: [ Project ] 30$ reprap plastic parts kit - 13 years ago
But think that your project is slightly wider...by Pacca - Plastic RepRap Parts for Sale
Re: [ Project ] 30$ reprap plastic parts kit - 13 years ago
for people looking for moulded parts, i saw a new category at eMAKERshopby Pacca - Plastic RepRap Parts for Sale
Re: [UK] £299 Full 3d printer reprap kits April 2011 - 13 years ago
this is exactly what I think ... this project will not be able to expand between young people and future generations if a kit has these prices!by Pacca - For Sale
Re: [UK] £299 Full 3d printer reprap kits April 2011 - 13 years ago
so I was not the only one looking for a kit that doesn't cost too much ...by Pacca - For Sale
Re: [UK] £299 Full 3d printer reprap kits April 2011 - 13 years ago
it seems that this will become the best selling kit a little curiosity: there is the heated bed?by Pacca - For Sale