altro modello rivisto e corretto in alcune parti 200x200x200 estrusore diretto stile M200 guide a ricircolo cloni Hiwin da 9 non mi fermerò qui ancora da migliorareby maralb - Progetti e nuove idee
Lo avevo preso in attesa di Alligator R3 SeeMeCNC lo monta sulle sue Delta serve una buona porta SPI per usarlo 35E speditoby maralb - Mercato
Pay close attention to the 5V limit switches and peripherals During the connection "One by one" if you see the LEDs bounce the light Means to be a short circuit. If you have a relay module and it happens a short one. After a few seconds cut off I use 2 cards with all original end enstop accessories etc. etc. Never any problemby maralb - Controllers
max 2 estrusori devi aggiungere un modulino di 8 euro la uso sulla Hbot con TMC2100 non mi lamento e mi accontento egreggiamente ne ho prese 2 se vuoi te ne spedisco una la provi e se ti piace mi regali 90 euri senza modulo secondo estrusore sto avendo qualche problema di stabilità temperatura, ma proprio oggi tramite Skype gli sviluppatori CINESI mi hanno detto di mettere a massa il negativoby maralb - Elettronica e meccanica
niente da toglier al grande Mago ma alla fine se non vuoi smadonnare troppo ce anche questa Lerdge.com tutto sta ad essere soddisfatti del funzionamento della macchina. se hai bisogno di giocare interfacciare parametri ecc. ecc. ci adeguiamo ai firmware per smanettatori e poi stiamo qui a riempire di domande e richieste qui sul forum. se ti accontenti della funzionalita basiche di una stampanteby maralb - Elettronica e meccanica
grazie Manu, ho risolto montanto questo semplice circuito collegandoci dirattamente il fungo oltre ad avere il pulsante on/off sull'alimentatoreby maralb - Elettronica e meccanica
Thanks you Even with printer stops 38/39 40 41 degrees. The tearing should not be stable and the fan always turns on / off I have installed and known led strips that pump light when and in print even if they are at 50% As if there was some disturbance on the lineby maralb - Controllers
All very strange When it stops, it seems to keep the temperature Installed again V 2.0 and verified with thermocouple tester Check the connectors on the board For bad weldsby maralb - Controllers
I started with a thermocouple, now I'm trying thermistor It seems that when printing and stops everything ok When it prints something the temperature fluctuates I'm doing a new video testby maralb - Controllers
Before I had version V1.01 and I did not remember these issues. Now mount V 1.02 with 2 fan connections I'm testing the firmware 1.17 beta 7 and I'm having the same problems. Cartridge inspection HE 12V 40w measured 3.8oHm. The cables are ok Activated pid tuning with Bed near Hend and cooling fan onby maralb - Controllers
I can not communicate with Tabao store, I hope someone can do it for me. I'm loading version 1.1.7by maralb - Controllers
Have many problems with HE v6 and temperature swing a lot. Tested with thermocouple and thermistor Always swing a lot Pid tuning many times Firmware 2.00 With 1.1.7 the temperature was always constant This and the result of the cube test with oscillating temperaturesby maralb - Controllers
Io sono un po Geloso ma con 400 ore di stampe ci guadagnate un po di eurini?? azz.. stampate tutto il giorno????by maralb - Estrusori, Hotends, Heated bed, Filamenti, etc.
accipicchia sembra un gioiello da regalareby maralb - Estrusori, Hotends, Heated bed, Filamenti, etc.
segui questo postby maralb - Estrusori, Hotends, Heated bed, Filamenti, etc.
On my Hbot I have X Y min NC all OK Z max NO all OK It does not work to set min temp. HotEnd My extruder motor also activates at low temperatures I seemed to have read running RGB LED on the new module 2 HotEnd 14. Modify the motor direction signal stabilization time (automatically set according to the mutation speed), to ensure that the correct operation of different external drives. 15. Optby maralb - Controllers
volendo collegare una Emergenza con fungo a 3 contatti C NC NO dove è meglio collegarlo?? TNXby maralb - Elettronica e meccanica
1.1.7 and also a BETA No bugs, but always Beta6 I use it with my HBot and also run bedlevel I'm waiting for the new Dual extruder module ........ See how it behavesby maralb - Controllers
Hello Friends, Warn firmware development It is possible to reverse the position of Touch X with Y Have some problem with the window exit from the screen. watch videosby maralb - Controllers
I use on my HBot With E3dv6 TMC2100 BLtouchby maralb - Controllers
To me pleasure lerdge Board I pay for what they like Possibility to remove the logo from the UI Better to payby maralb - Controllers
Now and for sale version 1.0.2 Output fan2 HotEnd controlled at 40 degrees I use it in my HBotby maralb - Controllers
forse voelva dire encoder dello schermo?? se usi il configuratore online ce una voce che ti permette di invertire il senso di rotazione "Reverse encoder direction" se cambi i parametri manualmente nel Configuration.h cerca (UI_REVERSE_ENCODER)by maralb - Elettronica e meccanica
ti consigli di attrezzarti con una squadra bella lunga e di alliniare le torri poi se possibile stampati 3 supportini tipo questi per tarare i carrelli con gli endstopby maralb - Stampa 3D per principianti
non sono convinto delle rotelle, io le monto sulla delta, ed ho visto stampati molto note che fanno scorrere testine di stampa su rotelle sono in nylon con cuscinetti all'interno e spessorate, se ben montate non fanno una piega. unica pecca devono essere sempre pulite e in una fresatrice non le vedo. anche per le cinghie in gomma il mio pensiero non cambia ottima riflessione sulla lavorazione dby maralb - Elettronica e meccanica
che hai costruito na torre di pisa?? mi sono sempre chiesto appunto come facciano tutte questa delta con endstop fissi senza regolazione il mio punto di riferimento è stata la Spiderbot (francese) che monta finecorsa di questo tipoby maralb - Stampa 3D per principianti
logicamente fornita di pulegge e cinghia pe X Y mancherebbero solo i motori, scheda di controllo, ali, e bed con vetro le foto sono quelle piu recenti che trovate nella presentazione stampa perfettamente dopo una bella taratura disponibile per qualsiasi chiarimento con aggiunta di 50E possibilità di aggiungere board Azteeg X3 Full con relativo Displayby maralb - Mercato
frame senza elettronica e motori monta Guide MG9 250 area utile 200x200x200 asse Z tipo ulktimaker con guide da 12 niente piatto riscaldato niente motore contattatemi per i particolari Quì trovate la presentazione 150euro spedita pagamento da concordareby maralb - Mercato