Is your configuration.h in Marlin setup right? type off motherboard, endstops, etc. Seeby gforce1 - General Mendel Topics
Die Schrauben von Motedis funktionieren ganz gut.by gforce1 - Projekte
Motors grinding: vref on your steppers not set right, max accelaration or speed in marlin too high. Extrudermotor not working: there is a prevention in marlin for cold extrusion set this temp lower than the roomtemp. Edit: do this only for testing.by gforce1 - General
Post your problems and question here on the forum, there is a lot off people out here who want to help you.by gforce1 - General Mendel Topics
I am not sure, i think it was about one week for my first order (1 set) and 2 week s for the second order (2 sets). here is a picture of the last one I made:by gforce1 - Allgemeines
Ok, good luck with the build. If you have any questions just ask.by gforce1 - Allgemeines
QuoteWurstnase Im englischen Forum hat gerade einer geschrieben, dass er schon 3 von den Dingern aufgebaut hat und damit zufrieden ist. Edit: Hier noch der Link dazu: That is correct. I bought three sets without the electronics. The electronics i bought on ebay search for seller fabster3d. He has every two days or so an auction. When you are lucky you have everything complete for just under €40by gforce1 - Allgemeines
This one is also very good. I have build three prusa's with this set. The hardware is complete and the printed parts are very good.by gforce1 - Reprappers
looks like the same problem. . Z axis artifactsby gforce1 - General Mendel Topics
Of zoals hier met een lcd en een sd-kaartjeby gforce1 - Software
What is your layerheight vs your z-axis pitch? See alsoby gforce1 - General Mendel Topics
QuoteNsverhagen Ik wil hem nog kunnen stopzetten, vertragen, versnellen en flow aanpassen Mvg, Natascha Dit kan allemaal via display met sd-kaart.by gforce1 - Software
Dan staat er iets niet goed in je slice programma, dit onderdeel moet gewoon kunnen met opvulling. Welk programma gebruik je?by gforce1 - Projecten
QuoteReplace As this is the new Flow-Rate thread, can anyone tell me if it is true that moving the flow rate bar during print, will only affect plastic throughput and no other stepper ? So actually it is to get more or less plastic than defined in the firmware and by the slicer , per mm travel for that object ? Thomas Heb je het toch ff aan de specialist gevraagd?by gforce1 - Software
QuoteOhmarinus Helaas, de activiteit van dit jaar was voor mij al de Dutch Design Week maar ik wens je veel plezier in Berlijn! Daar ga ik weleens heen om wat cultuur op- te snuiven. Mocht je tijd overhebben, boek een afspraak bij de Boros Sammlung, een aanrader! Beurs is in Eindhoven.by gforce1 - Algemeen
Balkje van verlaatsing gaat alles sneller dus de flow gaat evenredig mee met de snelheid. Balkje van flow verhoogd of verlaagd alleen de flow.by gforce1 - Software
swap theconnectors of the x and y-motors on the board and then print, if it is still in the y axis it is not your ramps.by gforce1 - General Mendel Topics
I think your accelaration or your speed or your yerk settings in marlin are to high. Lower them a lot and try again, if it is working then you can try set them higher. Sorry, i am from holland and can not write german.by gforce1 - Elektrik & Elektronik
Te koop: NIEUWE Prusa i3. Printklaar!!! De printer is compleet gebouwd en afgesteld. Alle bekabeling is netjes weggewerkt. Frame: - 6 mm dik aluminium. - 10 mm Y-draadstangen. - Aluminium Z-koppelingen. - GT2-timing belt met aluminium pulleys. Elektronica: - Arduino MEGA 2560. - RAMPS 1.4. 2 koelventilatoren. - Fan splitter. - LCD-scherm met 4GB SD-kaart voor printen zonder computer.by gforce1 - Marktplaats
if your hotend pushes the print from the glass bed, your steps/mm for your z-axis is set wrong.by gforce1 - General Mendel Topics
Check your endstop settings in marlin.by gforce1 - Controllers
these are mine settings: Prusa i3 //// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {50*60, 50*60, 4*60, 0} // set the homing speeds (mm/min) // default settings #define DEFAULT_AXIS_STEPS_PER_UNIT {80.00,80.00,3200/0.8,400} // default steps per unit for Ultimaker #define DEFAULT_MAX_FEEDRATE {200, 200, 2,by gforce1 - RAMPS Electronics
Accelaration on the z is to high. Set this about 1/10 of its value and try again.by gforce1 - RAMPS Electronics
Gewoon installeren, heb ik ook gedaan en alles werkt gewoon, alle instellingen worden mee overgenomen zelfs die van slicer. Ziet er mooier uit. Handmatig iedere as homen dmv knoppen. nieuwere slicer geintegreerd. mogelijkheid om prints te spiegelen.by gforce1 - Software
You can also use the max endstop, put it on the righthand side of your x-axis, and reconfig your marlin for this.by gforce1 - RAMPS Electronics
The most problems of not moving a motor are caused by a wrong setup of the endstops and the moving direction of the axis. Check this first.by gforce1 - RAMPS Electronics
Lcd scherm werkt ook als je met repetier host werkt, je kan dan zelfs nog dingen aanpassen via het scherm tijdens het printen. sd-kaartje hoef je niet voor te bereiden, gewoon je gcode erheen kopieren en je print via je schermpje vanaf sd-kaartje starten.by gforce1 - Electronica
Thanks guys. I ment the smooth rods. I was thinking, if i mount the heatbed on a corexy system also and reverse the direction of it. So it travels opposit the extruder corexy then the printspeed will be twice the normal speed. You only have to adjust your travelsteps because rhe distance will be double. Is this possible?by gforce1 - CoreXY Machines
you have to change the value "extrude mintemp 150". you have to set it lower as your temp for the hotend.by gforce1 - Reprappers